How to Make a Cup Turner Cheap | DIY Double Tumbler Turner for less than $30
ฝัง
- เผยแพร่เมื่อ 27 ก.ค. 2024
- This DIY Tumbler Turner will cost you less than $30. It’s super easy to make and you could get it done in a couple of hours! I used ¾ inch plywood from the hardware store but any scraps you have could probably work! You can also adapt the sizes to meet your needs or even make a 3 or 4 cup turner! The PVC Pipe that I used was 3/4 inch and I glued it to the turner with E6000 glue.
I chose to go with the kit because at this moment in time it was the easiest thing I could do. You can find all the caps and screws to use 3/4 inch pvc pipe. Here are the motors without caps and arms: amzn.to/30jN527
WATCH NEXT!
-Epoxy Vs CrystaLac: • Epoxy vs Crystalac Tum...
-How to Glitter a Tumbler with Brite Tone: • How to Apply Glitter u...
-Smoke Method Tutorial: • How to make a Smoke St...
I participate in various affiliate programs. Some links that I share may provide me a small commission if you make a purchase. This is at zero cost to you. I only recommend products I use personally!
Make this cup yourself:
-¾ inch plywood cut into: 1 - 11 inch x 11 inch piece, 2 - 11 inch x 7 inch piece, 2 - 1 inch x 5 inch pieces
- Turner Kit: amzn.to/302FZ1L
- Wood Glue: amzn.to/3j73MEY
- Smart Plug: amzn.to/2RPDr2r
-Replacement Pipes: are currently unavailable, but this is the brand turner i have and bought the pipes from them amzn.to/3mJJi7H
-Motors without the arms (you can get caps and pvc at the store and screw it in yourself): amzn.to/30jN527
Other tools:
-Clamps: amzn.to/3cpbJTF
-Circular Saw: amzn.to/2RMVExH
-Drill Bits: amzn.to/35YfCh6
Click here to subscribe: / alisoncrafts
--------------------
Making Tumblers, keychains, pop sockets, and Starbucks cups are some of my favorite crafts! If you're interested in learning more and exactly how to make them yourself, you're in the right place!
Crystalac Introduction Series: • Playlist
Tumbler Basics: • Beginner Tumbler Tutor...
Keychain and Acrylic Blank Tutorials: • Epoxy Free Keychain Tu...
All tumbler tutorials: • Playlist
Silhouette Basics:
-------------------
Shop tools I use often for my crafts: craftingthegoodlife.com/amazo...
------------------
LET'S CONNECT!
Insta: Alison.crafts_
Blog: www.craftingthegoodlife.com
TH-cam: / alisoncrafts
TikTok: vm.tiktok.com/ZMJrVkFwL/
----------------- - แนวปฏิบัติและการใช้ชีวิต
![เปิดบ้านสุดหรู "เเจ็ค the ghost" ลั่นถ้าป๋องกพลลำบากผมเลี้ยงเอง!! l [Nickynachat]](http://i.ytimg.com/vi/1xbW4vULqGc/mqdefault.jpg)
Learn how to DIY your own Cup Turner! This one is for two cups but can easily be modified. I go through it pretty quickly, so comment or reach out on Instagram if you have questions! For Tumbler Tutorials click here: th-cam.com/play/PLY1xNd7MWi5sdm13LW0yWxefpH06iLiCR.html
Hey, the motor with the screw that keeps coming loose is turning the opposite direction of the other motor. If you change the orientation of the wires on the back of the motor, then it should turn the other way... which may stop the screw from loosening. Hope this helps!
Watching now, but you know what I really like about your tutorials ? They’re short, sweet, & to the point. I am subscribed. Thank you!!!!!
Thank you for subscribing! I'm so glad you like the videos 💕 no one has time to comb through and hour long tutorial lol!!!
You should be able to replace the pvc cap and pvc arms with standard size pvc. Also try a little loctite on that screw.
I agree with the other posters, I love your tutorials! It's nice to have someone who's concise, and straight to the point. Thank you.
Thank you
Thank you for sharing this tutorial. It’s been the most simplest I’ve ever seen on making a cup turner. Definitely something doable.
Totally doable!
You can use a cap of the size of pvc and drill a hole and use an M5 screw to attach the cap to the motor.
Great tutorial...I know you're in the U.S. and we have different amazon and stuff from you....but just linking stuff makes it easier for me to find it here. I've never done a tumbler turner but I'm interested to make my own.
Thank you so much! LOVED the entire video. Cheers :)
Thanks for sharing getting ready to order mines now 😊
Thank you so much for your tutorials, they are very easy to follow thank you 🙏🏼🇦🇺
THanks for watching
Thank you so much :) Happy new year :)
I like this idea. Thanks so much for doing this tutorial.
Thanks for watching!
Omg, you're teasing me with the HP book tumbler in the video. Need that tutorial yesterday! Haha
soon!!!
I changed mine to a 3/4 inch CPVC and just used the flat end caps.
Nice job
I figured out the cap problem not fitting 1/2” pvc pipe. I bought 1/2” caps from Home Depot. I drilled a hole in the center to fit in the end. Now I can use 1/2” pvc pipe.
The screw that keeps coming loose, I would recommend Threadlock. Cheap bottle of blue stuff that will hold the threads in place. its the reason that Store bought products are so difficult to take apart.
The blue caps that the wands connect into can probably be replaced with pvc caps that are threaded. I did that with the turner bought from amazon so I could make it extra wands to change out.
I'm deliberating making a 4 (or even 6!) Cup turner. I'm scared, but I may need to go for it. My one cup turner isn't enough
do it!! It will be so nice to have a lot of turners!
@@AlisonCrafts I'm nervous, but I think I'll try! A 4 cup one. Need to find decent lumber at a good price
What were the measurements you used to drill out the holes with the spade bits?
Does the screw you tightened with the wrench and screwdriver you said kept coming loose hold the piece that the tube slips into? If so you could use a piece of half inch or 3/4 inch PVC and end caps for replacement rods.. just drill a hole in the center of a cap and the PVC pipe will slide right into it.
I suggest you put a lock washer to prevent the screws from coming off.
Do both motors plug into the one side together? So in parallel?
Personal opinion…I watched the video on the globeous and was holding out to buy that…however I would like a mult spinner (I just planned on buying more globeous singles)….what do you think? I know there were several reasons you liked the globeous…space, 2 way direction spin, etc
You could put lock tight on screw and it would not keep coming loose
I used E6000 and it came loose. Ugh. I will try loctite!
Do these spend all the way around? Or stop and reverse?
Hi Alison, Hello from the UK , yours is not the first tumbler turner channel that have made this request ,that said, @4:09 , I have purchased this same motor ( AC 100 -127v ) I'm a wood turner and I need to make a motorized turntable , with said motor , wired it up left it running while I found the grub screws and Allen wrench got back it was over heating , it was rather hot , the problem maybe the voltage (UK mains electric runs on 240 volts ), any help would be appreciated,,. Stay safe,. Regards Alf
I'm pretty sure that motor can spin either way.. you may be able to grab the arm and switch the direction to keep the screw from unscrewing
It has been helping to only have it spin towards the right so the screw doesn't get loose while spinning!
darn the motor setup kit is no longer available on amazon
Use BLUE LOC TIGHT on any screws that come loose..it will keep them from coming loose but you can also take them off if needed
Thank you! I just got some to add !
Use blue loctite for the screw that keeps getting lose.
Thank you! I'm glad to hear you recommend it, i just bought some last week LOL!
Where your screw keeps loosening take it out and put some kind of glue or adhesives behind it.
Link for motor kit on amazon?
The link you provided for the motor kit is not correct.
Sorry if I missed it, but did you include a link for the tumbler turner you said you bought from Amazon?
amzn.to/3AV2sxt
Thank you!
The side that comes loose is reversed polarity .it spins the opposite direction so it comes off.simply switch the wires around on that motor....
Where is the link to the spinner you bought off Amazon. I am not able to make one myself right now
www.amazon.com/shop/alisoncrafts?listId=2692C777II1V8
I have a question... do you know how I could obtain a replacement for the hobby lobby's single cup tumbler maker Turner arm screw all I see is long screw, it don't even have a name all I see is "long screw"?
And also I would very much appreciate it if you could see about the other parts of the your DIY Tumbler Turner please. Thank you Kindly
How do you make this without purchasing the motors?... Like make the motors from something else like a clock or something?
I’m not sure, but they’re pretty cheap now to just grab on Amazon! amzn.to/42dHnxl
Try putting some thread lock on that screw that keeps working out.
What are you using to hold your cups, are you using footballs?
I use foam but going to transition to 3D printed inserts! The foam is listed here under tumbler tools www.amazon.com/shop/alisoncrafts
I’ve had the same question for a week with all kinds of search results with no leads or ends. The ones on Amazon are currently unavailable. Is there anyway to get the link to 3D print them? Please, thank you 😊
Less than $30? Amazon has several for that price.
add a little blue lock tite.
Where to buy this
Links to supplies are in the description
Change the direction of the one motor that’s unscrewing
Think I’m going to the dollar tree. For. A cup turner it’s 5 bucks 😊
This video is old, there weren't as many options as there are now! Definitely super easy to find one to buy, just read some reviews first :)