Oof, preparing those nails, adding yellow bushings and gluing balls probably was a TREMENDOUS amount of work 😲 Still, thank you for this video, really inspiring and well-executed! 🌟👍
It's more of a simple concept than much of your other devices. But setting up all those nails look far more tedious than anything else you've done! You have the patience of a saint to do all of those! You have my eternal respect.
I don't know how this video appears here in eastern Europe, but thank you, it was a huge satisfaction. Female engineers are rare, and I have huge respect for that.
If you design the nail-cutting jig to be taller, you wouldn't need to shim each one before cutting. You could make the uppermost section of each hole looser to make it easier to push in and pull out, too. You could even incorporate the final grid into this cutting jig to save you from taking them all out and reinserting.
Pretty cool looking. I think I would have printed the yellow tubes with an internal wall a few mm from the ball bearing end. Make them easier to position the same height. I did something like that for holding dremmel tools. I printed a case from filament with threaded holes and then threaded inserts that held the shafts from tough resin with a little bit of spring grip.
I believe that beveling the sharp back edge of the windmill "blades" to a steep slope, would reduce the noise a bit. The pins would slide down that quickly, instead of slamming down from a small freefall.
ziet er echt prachtig uit. Ben vooral onder de indruk van het gebruik van standaard onderdelen die iedereen wel kan kopen. geweldige video, ga vooral zo door 👍
Если между штырьками и подвижной платформой проложить рамку с эластичной и скользкой тканью типа капрона или фатина, на штырьки не будет приходить трение от вращающейся платформы, что снизит боковой перекос...
凹みバージョンが1番不思議な動きに見えて好き
それな
11:40
True, from Spain
True, from Japan
Thank you for adding English subtitles! I love your work, and am happy that I can follow along better now 😁 Looking forward to your next project!
just read your comment as i finished the video with subtitles turned off
恐ろしく地道な作業で尊敬しかない
別バージョンのカムが出てきたときニッコリした
It looks like magic when it's the indentation plate, but the positive indent plate is mesmerizing. Very cool project, very well executed.
凹みバージョンは、ほかのバージョンと違い、何もないところを勝手にボールが進んでいるという、不思議な感じを楽しむことができるので、へこみバージョンが一番よかったです。
いつの間にかアイコンが変わっててびっくりした!
今回のも不思議とずっと見ていたくなるからくりだなぁ
偶に引っかかって元通り沈みきらない問題児の釘すき
The things you come up with are always so fascinating. Love your work.
な に こ れ w
作業量がエグくて笑いましたわw
発想、設計力すべてが天才過ぎる
凹みバージョンが特に良かった。いつもながら良いですね
Oof, preparing those nails, adding yellow bushings and gluing balls probably was a TREMENDOUS amount of work 😲
Still, thank you for this video, really inspiring and well-executed! 🌟👍
なんと素晴らしい……
羽バージョンがASMRっぽさもあってずっと見てられる
Art meets engineering, I love it!!! It would also be really cool to reuse this idea for a clock.
動きが滑らかで気持ち良いですね
釘カットは最初から丁度良い長さの治具を作った方が良いような…
いつにもまして地獄みたいな工程だ…
It's more of a simple concept than much of your other devices. But setting up all those nails look far more tedious than anything else you've done! You have the patience of a saint to do all of those! You have my eternal respect.
異常に多い単純作業で指怪我してるし…
すげえよ…
これが重力波ちゃんですか
作業量がエグい!お疲れさまでした✋⚡⚡
CPUの裏側かな?😂
ピン折れ不可避で草
Socket478かな?
びっしり並んでるからAMDのAM2とかかもしれん
I absolutely love your videos! They're a great source of inspiration for my own making, and btw thank you much for including subtitles! :)
That's insane! What a crazy amount of work for such a pretty effect.
Wow, that is fantastic, I could watch it all day! Great work!
This is such a simple but smart design. Looks great! Keep it up!
As always this is incredible. I was impressed with the time and efforts involved on the making of this one.
一生見てられるやつ
You are such a brilliant designer and fabricator. It as an absolute delight and pleasure to watch your work. Thank you so very much 🙏🏾
Beautiful. The reflection of the nails on the ball is neat!
Great idea! Love it!
アイコンいつの間にか可愛くなってた
好き
The windmill version sounds good 👍
Thank you for the English subtitles! That's a really cool project.
This looked very time consuming and beautiful. Good job!
Interesting little desk toy, great work
This is some fine engineering right here.
釘の作業が苦行すぎる……。すげえ。
''くぎ''の作業が苦行(''くぎ''ょう)すぎる…ねぇ
You have great patience and the end result was worth it. Amazing.
とてもかっこいい
In awe at your talent
これ地面とか廊下に張り巡らすように設置して、立ってるだけで移動できるようになったら凄いよなぁ
I absolutely love this desktop toy! Great job! Love the design!!! You should sell these
This is so cool, very mesmerizing to see built as well as see functioning! Excellent work!
Incredible dedication
Amazing work
Brilliant! Nice work!
羽バージョン、気持ちよく動いてて好きだなあ
玉を転がさなくても波とか再現できると視覚効果で癒されそう
Pretty ingenious!
最後の羽バージョン時計みたいで好き
11:10 マッサージチェアの腰あたりの挙動だ
ところで、これ工夫すれば歩行者用信号機出来るかも
ちょっとやってみる
これが置物としてあったらロマンしかない
それな!
I don't know how this video appears here in eastern Europe, but thank you, it was a huge satisfaction. Female engineers are rare, and I have huge respect for that.
That looked so mesmerizing! The concave version looks the best with the marble, but without the marble, the two version is incredibly interesting
凹みバージョンの玉乗せる前、視えざるものが転がってる感じがして好き
Cool idea for a clock
😮 I'm inspired by your work!
左手人差し指の傷から大変な作業だったことがわかる
(っ´ω`c)はやくよくなれーッ
This is so cool!
If you design the nail-cutting jig to be taller, you wouldn't need to shim each one before cutting. You could make the uppermost section of each hole looser to make it easier to push in and pull out, too. You could even incorporate the final grid into this cutting jig to save you from taking them all out and reinserting.
The windmill is so trippy!
Wow. This is wonderful.
すげぇぇぇ
this made me happy. thank you.
これは私を幸せにしました。 ありがとう。
(グーグル翻訳)
Pretty cool looking. I think I would have printed the yellow tubes with an internal wall a few mm from the ball bearing end. Make them easier to position the same height.
I did something like that for holding dremmel tools. I printed a case from filament with threaded holes and then threaded inserts that held the shafts from tough resin with a little bit of spring grip.
Really cool!
めちゃ欲しい‼️
Windmill looks trippy
Nice creation
ウルヴァリンの富豪の爺さんが寝てたベッド
駆け出し設計者として尊敬します
羽バージョンの音が好き
Thats really cool.
Real commitment!
Che figata !
Super cool! My favorite one is the concave version, it looks like the balls are moving by themselves
Thank you for the subtitles!!
気の遠くなる作業だあ
looks great. my clumsy hand would never able to do half of those "nailing"
あれはすばらしい!
ええすご
You are awesomely creative I love you 🥰
今までの機構とは比べ物にならんくらい地道な作業で見てるだけのこっちが狂いそうになった
Omg the glueing step i cant. Id lose my mind.
売られたら買うわこんな凄いの
imagine a nail wave machine the size of a room
I believe that beveling the sharp back edge of the windmill "blades" to a steep slope, would reduce the noise a bit. The pins would slide down that quickly, instead of slamming down from a small freefall.
アイコン変わっていいですね😊
今回のカラクリも面白いですね
a nice little machine :) just be careful not to get a repetitive strain injury
ziet er echt prachtig uit.
Ben vooral onder de indruk van het gebruik van standaard onderdelen die iedereen wel kan kopen.
geweldige video, ga vooral zo door
👍
Love the concave because it is impossible to perceive what is happening. :D
Excellent, I'd like to make one.
凄い!
Excellent
very neat
この機構を上手く使って、玉を針に見立てた時計があったらめちゃくちゃカッコイイしインテリアになりそう😊
So cool!
Love this 😊🖤
すごい、、、、
Если между штырьками и подвижной платформой проложить рамку с эластичной и скользкой тканью типа капрона или фатина, на штырьки не будет приходить трение от вращающейся платформы, что снизит боковой перекос...