How to Program ESP01 WiFi Module | Arduino IDE | DIY
ฝัง
- เผยแพร่เมื่อ 24 ธ.ค. 2020
- $2 for 2-Layer PCBs & $5 for 4-Layer PCBs: jlcpcb.com
More project information(Code,Schematic,etc):- nematicslab.com/how-to-progra...
Website,
NematicsLab.com
Patreon,
/ nematicslab
For Sponsorships or Endorsements ONLY!
Business@Nematicslab.com
For project-related questions use Facebook or Twitter @NematicsLab
Music used in the video:
1) Manhattan by Dyalla
2) Yellow Flamingo by Sarah, The Illstrumentalist
3) Stars and Constellations by Sarah, The Illstrumentalist
4) Space Navigator by Sarah, The Illstrumentalist
--------- Links For Parts Used in the Video---------
FTDI - www.banggood.in/custlink/mG3y...
ESP01 - www.banggood.in/custlink/K3Dy...
Jumper cables - www.banggood.in/custlink/3DDd...
Bread Board - www.banggood.in/custlink/mGmE...
--------- Affiliate ---------
Gearbest- bit.ly/2KD54KD
Banggod- bit.ly/2xgJIK5
LCSC - bit.ly/2KD0hJ0
--------- Social Media ---------
Facebook - bit.ly/2FC5lJz
Instagram - bit.ly/2XddQpe
Twitter - bit.ly/2IUhqMm
-------------------Electronics Starter kit Tools-------------------
Soldering Iron - www.banggood.in/custlink/DKGK...
Solder wire - www.banggood.in/custlink/mv3v...
Helping Hands - www.banggood.in/custlink/vmvm...
Hot Glue - www.banggood.in/custlink/D3GD...
---------------Little information about Video------------------
The ESP8266 is a low-cost Wi-Fi microchip, with a full TCP/IP stack and microcontroller capability, produced by Espressif Systems in Shanghai, China.
The chip first came to the attention of Western makers in August 2014 with the ESP-01 module, made by a third-party manufacturer Ai-Thinker. This small module allows microcontrollers to connect to a Wi-Fi network and make simple TCP/IP connections using Hayes-style commands. However, at first there was almost no English-language documentation on the chip and the commands it accepted. The very low price and the fact that there were very few external components on the module, which suggested that it could eventually be very inexpensive in volume, attracted many hackers to explore the module, the chip, and the software on it, as well as to translate the Chinese documentation.
The ESP8285 is an ESP8266 with 1 MiB of built-in flash, allowing the building of single-chip devices capable of connecting to Wi-Fi.
The successors to these microcontroller chips is the ESP32 family of chips, including the pin-compatible ESP32-C3. - วิทยาศาสตร์และเทคโนโลยี
Thanks, clear directions and info regarding the relationship of GPIO0.
You got a new subscriber :) why did I need this it helped me make a wifi hotspot to put in my car :)
Nice info, well done, thanks for sharing it:)
Hi, thanks for nice video. Can I connect to esp01 which is on home wifi from my smartphone which is on other network maybe in some other region?
wow, so good, but why dont you upload this circut in discription
part ?
Nice work ❤️
Hi sir can you provide the Gerber file of the designed pcb of led panal which you have uploaded the video for the led panal. please provide that file please.
Considering the cost of FTDI board and the custom PCB, I think ESP12 Node MCU is more cost effective and easy for a beginner. Plus more GPIO pins
Depends on if you want to buy only a single one of these boards or more. You don't need to put the FTDI and breakout boards into the final project and can reuse them. And when it's just about cost, a lot of people already have an FTDI board and you could make that breakout board on a breadboard.
Excellent
Can you share the pcb of easyeda
Thanks
perfect! tx!
i tried at least 50 hours on this, but no led blinks at all . what could be wrong?
Pwoli bro
Hii brother can you please make an automatic water level controller just like kiyani tech made. He used atmega ic instead of complete arduino board so circuit became quite difficult. I request you to please make same as he did by using complete arduino board
What was your board settings? The blue led does flash, but the arduino ide says an error, espcomm_upload_mem failed
Actually his connection is wrong.
Should connect TX to TX and RX to RX.
Then check. It definitely works
@@vamsikrishna-cr4xu 100% correct. It worked for me. Thanks. Used Arduino Uno R3 to program it.
@@BrinleyPavitt 👍 😊
How to drive Servo with ESP-01
i cannot get it to run any code :(
nice project... boleh tak buat video tentang touch some object, n music will play by Arduino. 😊😊
Good channel
Can you please advice how to make this using Arduino Uno ??
nice
Damn I spent last 4 days doing the same thing and now you drop this lol
Haha I hope it helps
So my Arduino IDE does now show the ESP board - how do I get those settings?
th-cam.com/video/W7AHNkxcrxs/w-d-xo.html
@@Nematics_Lab thank you! so now I am trying to test sending AT commands. I have the MakerFocus ESP8266 ESP-01 Serial Wireless WiFi Transceiver Receiver Module 1MB SPI Flash DC3.0-3.6V
Keep getting this, followed the wiring exactly. "Failed to connect to ESP8266: Timed out waiting for packet header
Failed uploading: uploading error: exit status 1" Happens when uploading the blink example... help?
i'm stuck on this error for weeks, feels like I tried everything. did you manage to solve this?
@@user-nq4vz3jq4o just for you to know I got tired of this error . Got a nodemcu with an esp8266. Works like a charm although I feel like wasting resources cause I don’t use half of the chip.
Accent 100%
😍😍😍
👍
ESP 01 programming with NodeMCU 8266
Made signal jammer for mobile phones with a 10-20m range pls
With less components
👍👍
❤️❤️❤️
i am noob but i like it
Why don't you start selling that board in your website
Due to COVID 19 as of now. but you can expect than from New year!
@@Nematics_Lab 👍🏻
Yo
Yo
@@Nematics_Lab one question how to calculate power output of a 775 motor
P = V*I will give you rough estimate
@@Nematics_Lab I found same formula on net but their will be less power output. Actually I am detail designing gear box for 775 on creo.
jlpcb is a shit company and very expensive. but for you its ok
i needed to know how to programmed so it connects to the WiFi, instead you are showing some code for making it blink. This module is for WiFi connectivity, not for Light Efects porposes
Do you know how to do this, or you are some pseudo-specialist, who does not know anything?????????????