please do a clear wiring build for this F722 SE and show it is working..i dont want wiring schematic on their website. video is easier to understand.
6 ปีที่แล้ว +1
I think something like "real pit" we can manage to work with buzzer pin too on other boards (and limited to 5V output). Buzzer (negative) pad already has transistor what we can control via pinio. Of cource we sacrifice (piezo) buzzer function , fortunately we have dshot beacon ;)
are you saying we've had real pit all along! mind=blown ;)
6 ปีที่แล้ว +1
@@drdrechronik Something like that. But pinio came with bf3.3 (2018. march) and the buzzer pin has some limitation: 5v and (possible) very low current.
Hey, how can I tell if the FC supports the functionality or if it is the "vbat powered and camera pads switching" mode only supported? And if only the latter, can is there a way to remap the function to power something or do I need the additional little realpit board?
Hey pawel, I wondering if matek thought to add a slight delay between vbatt and vtx power, so that you can connect the battery to the quad without powering the vtx and blowing someone out of the air... That would be the cherry on the cake!
That's pretty fantastic, dude. And the camera switcher should be great for wings, because you can have one looking forward and the other looking backward. 😃
Hi Iam struggling to configure the matek F722SE board properly. When the board is connected to iNav, everything is working well (servos are working, motor is running with the iNav Master switch, Pre-arming check all green, (no GPS)everything fine) but when I disconnect the board from my computer and try to arm it, it’s beep ones,with the blue led flashing and the motor doesn’t want to run . I have flashed the board with the latest firmware inav 3.0 but it doesn’t resolve the problem. I don’t know what is wrong, does any body have an idea please
Nice video! Can you also use "normal" pit mode in inav? Im unable to find how to set it up was expecting to be as simple as in betaflight but the option is not there. Than i tried programming tab but also not able to do it there. I also asked chatGPT but he is wrong😂 Do you have any advice for me? Kind regards
Hello I've just subbed to your channel for this is about the fifth video I've watched of yours you seem to do or use everything I do haha!! This board being one of them will be here tomorrow, I am using it on a 7" long range bird and I am using R9M module the new one 2019 for the Taranis X9D plus and thank you much for THOSE vids!! The FPORT and R9M and R9MM ones for YOURS were only ones really that helped me much except for Cyclonefpv his vid was awesome as well on the subject and shows clearly and why he is doing what he is doing as you do, I LIKE TO KNOW THAT IF I AM GOING TO DO IT YA KNOW??!! hahaha I don't want someone to say connect this here and say go and not have a clue what I just did there's no sense in that to me....SO sorry...my question is could you PLEASE do a vid on how to do FPORT for anything I spose but in my case R9M and R9MM especially but should be same for whatever I'm thinking....I know how to do serial links and think on this board unfortunatly at least from what I am gathering from the manual is it does do FPORT and SPORT but you have to serial link RX or TX 2 is it I believe? and I am really not fully knowledgable in doing this and I want to do it but want to do it right and know what and why I am doin what I'm doin haha get me?? I would love to see a vid on this or you shoot me a PM and "SPLAIN" it to me haha....Like I said I get it and you go into CLI and tell it this pad is this now but I have only done it ONE Time and was a while back so if may be some diff in newer BF or F7's? I do not know? Thanks if you can help!! Great video!! L8r-Turbo.
Pawel....I have gone round and round with this all over the place...i really enjoy your vids, and I am almost exclusively an INAV user....wouldn't care if Betaflight dropped off of the face of the earth.....NOW...with that being said, I am aware of the 722SE...I have 2 of them sitting in their packages...I dont care about them right now....I am using a Kakute F4 AIO V2...with a BICKS camera switcher.... INAV configurator 2.1.1, and 2.1.0 on the Kakute......I NEED PINIO to work....it apparently does not...and if so Where in INAV?? there is no "user1 in modes....there is no "set pinio box" or otherwise.....where oh where is this mythical beast???
please do a clear wiring build for this F722 SE and show it is working..i dont want wiring schematic on their website. video is easier to understand.
I think something like "real pit" we can manage to work with buzzer pin too on other boards (and limited to 5V output). Buzzer (negative) pad already has transistor what we can control via pinio. Of cource we sacrifice (piezo) buzzer function , fortunately we have dshot beacon ;)
are you saying we've had real pit all along! mind=blown ;)
@@drdrechronik Something like that. But pinio came with bf3.3 (2018. march) and the buzzer pin has some limitation: 5v and (possible) very low current.
Hey, how can I tell if the FC supports the functionality or if it is the "vbat powered and camera pads switching" mode only supported?
And if only the latter, can is there a way to remap the function to power something or do I need the additional little realpit board?
Hey pawel, I wondering if matek thought to add a slight delay between vbatt and vtx power, so that you can connect the battery to the quad without powering the vtx and blowing someone out of the air... That would be the cherry on the cake!
Also nice to be used to reboot HD cameras in flight in the case they hang
would love to see the build, want to do another long range
That's pretty fantastic, dude. And the camera switcher should be great for wings, because you can have one looking forward and the other looking backward. 😃
Hi Iam struggling to configure the matek F722SE board properly. When the board is connected to iNav, everything is working well (servos are working, motor is running with the iNav Master switch, Pre-arming check all green, (no GPS)everything fine) but when I disconnect the board from my computer and try to arm it, it’s beep ones,with the blue led flashing and the motor doesn’t want to run . I have flashed the board with the latest firmware inav 3.0 but it doesn’t resolve the problem. I don’t know what is wrong, does any body have an idea please
great video! is same thing possible in inav?
yes
Hi! I would know how work the Transmitter with the external antenna? You know how much grow up the signal? Thanks!
I'm actually not using this radio very much, so it's really hard to tell
@@FPVUniversity Thanks anyway! 😜I love it's firm similar to the ps3's joypad that is very comfortable!
This is very cool. They need to make one on 20x20 format for my acroBrat.
they do. It's called F722-Mini
Nice video!
Can you also use "normal" pit mode in inav? Im unable to find how to set it up was expecting to be as simple as in betaflight but the option is not there. Than i tried programming tab but also not able to do it there.
I also asked chatGPT but he is wrong😂
Do you have any advice for me?
Kind regards
MATEK F722-Mini is the best FC of the world !
Hello I've just subbed to your channel for this is about the fifth video I've watched of yours you seem to do or use everything I do haha!! This board being one of them will be here tomorrow, I am using it on a 7" long range bird and I am using R9M module the new one 2019 for the Taranis X9D plus and thank you much for THOSE vids!! The FPORT and R9M and R9MM ones for YOURS were only ones really that helped me much except for Cyclonefpv his vid was awesome as well on the subject and shows clearly and why he is doing what he is doing as you do, I LIKE TO KNOW THAT IF I AM GOING TO DO IT YA KNOW??!! hahaha I don't want someone to say connect this here and say go and not have a clue what I just did there's no sense in that to me....SO sorry...my question is could you PLEASE do a vid on how to do FPORT for anything I spose but in my case R9M and R9MM especially but should be same for whatever I'm thinking....I know how to do serial links and think on this board unfortunatly at least from what I am gathering from the manual is it does do FPORT and SPORT but you have to serial link RX or TX 2 is it I believe? and I am really not fully knowledgable in doing this and I want to do it but want to do it right and know what and why I am doin what I'm doin haha get me?? I would love to see a vid on this or you shoot me a PM and "SPLAIN" it to me haha....Like I said I get it and you go into CLI and tell it this pad is this now but I have only done it ONE Time and was a while back so if may be some diff in newer BF or F7's? I do not know? Thanks if you can help!! Great video!! L8r-Turbo.
Pawel....I have gone round and round with this all over the place...i really enjoy your vids, and I am almost exclusively an INAV user....wouldn't care if Betaflight dropped off of the face of the earth.....NOW...with that being said, I am aware of the 722SE...I have 2 of them sitting in their packages...I dont care about them right now....I am using a Kakute F4 AIO V2...with a BICKS camera switcher.... INAV configurator 2.1.1, and 2.1.0 on the Kakute......I NEED PINIO to work....it apparently does not...and if so Where in INAV?? there is no "user1 in modes....there is no "set pinio box" or otherwise.....where oh where is this mythical beast???
I'm running iNav 2.3RC3 and I also see no support for PINIO, USER1, USER2 etc. PINIO doesn't even show up in resources. Was this feature removed?