Mitsubishi MR-J2-CT Commissioning. STEP 1 of 4. Parameters upload

Part 1: • Mitsubishi MR-J2-CT Co... (This video)
Part 2: • Mitsubishi MR-J2-CT Co...
Part 3: • Mitsubishi MR-J2-CT Co...
Part 4: • Mitsubishi MR-J2-CT Co...
​​​​​​​​​1) From the position page press the “far right” button and press “TURRET UNCLAMP”.
VERY IMPORTANT: UNCLAMP the TURRET before proceed
​​​​​​​2) Move mouse cursor to lower left corner of screen, left click to get Windows start bar up.
3) Go to “Programs”
4) GO TO MR-J2-CT Setup Software
​​​​​​​5) Click on MR-J2-CT Setup Software when it comes up the second time
6) Left click on SETUP AXIS
7) Left click on AXIS SELECT
8) Select axis “TURRET”
9) Check in blue margin at top of screen to make sure correct axis was selected.
10) Open TEST OPERATION
11) Click OK to warning screen.
12) You must be in “Jog” in “Operation mode (R)”
13) Check the box “ABSOLUTE POSITON INITIAL SET (A)”
14) Left click on ORIGIN-SET(S)
15) Left click on NORMAL ROT, axis jumps to Z phase. Use REVERSE ROT. if linear axis
16) Numbers in MACHINE EDGE and POSITION should match
17) Close software and POWER CYCLE the machine (turn off control, turn off main breaker for 15 seconds)
18) After machine has rebooted, UNCLAMP the turret again
19) Go back to MR-J2-CT Setup Software​​​​​​​
20) Change operation mode to REF.RETURN.
21) Press STOP (O)
22) Press REVERSE ROT(R)
23) Position window should show all zero
24) Initial set state window should show “Completion”
25) Close software, you are done.
If you need to step axis to position:
a) In TEST OPERATION under OPERATION MODE, select “Step”
b) Select increment you wish to move axis, ie; .001mm/deg,.01mm/deg, .1mm/deg,1mm/deg.
c) Left click stop to clear commands or when you change direction.
d) Left click either NORM. ROTATION or REV. ROTATION to move axis into position.
f) NOTE: Make sure turret is unclamped

[@saravanansaru668]

Very useful massage

[@FabianAchaval]

Thank you

[@douglasrodriguez5530]

Gracias valiosa informacion

[@maciejkuzma8186]

Hello, can you help me set the magazine, is the battery dead?

[@grr1mhmt]

Hello Mr Fabian, I have a problem about uploading parameters from pc. Software is giving Data protection alert. Do I need NC machine or can I solve it without NC ?

[@FabianAchaval]

Hi there. To upload parameters to a Mitsubishi MR-J2 drive from a PC, you can use the MR Configurator software. This software allows you to easily tune, monitor, read/write parameters, and test operations from your personal computer. Here are the general steps you would follow:
Install the MR Configurator software on your PC. You can download it from the Mitsubishi Electric website.
Connect your PC to the MR-J2 drive using the appropriate RS-232-C communication cable.
Launch the MR Configurator software and select the MR-J2 drive you wish to configure.
Navigate to the parameter settings within the software to view and modify the parameters.
Upload the parameters to the drive by writing them from the software.

[@xcyong89]

Hi, could u share the MR-J2-CT Setup Software?

[@FabianAchaval]

s3.amazonaws.com/MEAU/Free+Software/MR-J2-CT+Setup/A0/MR-J2_SET_UP_S_W.zip

[@FabianAchaval]

If you cannot access, you might have to create an account with Mitsubishi at us.mitsubishielectric.com/fa/en

[@xcyong89]

@@FabianAchaval Hi, thank you for the software, it works

[@fumingjeh]

Thanks a lot Bro!!! I'm a CNC technician too from 🇲🇾 Malaysia. Been looking for this a long time a go