Good stuff! I don’t care what anyone says, better than a pressure pot sandblaster in so many ways, provided the pressure washer is decent. I done a whole engine bay if you haven’t already seen. Works great! Thanks for watching!
Really great results! This is the best I have seen. I noticed that these particular blasters need 4gpm to work. I was all excited until I found out my pressure washer only does 2.5gpm. So, a high volume pressure washer is a must. The extra water flow you added from your source made all the difference because your pressure washer can handle the volume needed. Great video!
Great video which I watched after total frustration with my $50 amazon purchase.of a water blaster attachment - it seems my professional Karcher 5/12C. You definitely made the right decision investing in professional grade equipment to avoid pitfalls. Looks like you need to spend a grand to achieve top grade professional results. (as usual). My Karcher apparently hasn't got the guts to create enough suction to transport the media. from the bag (80 Grit Garnet purchased from H&F) to combine with the jet stream....... Based on your set up the karcher flow rate is probably too low at about 10l/min and 2200psi. Your thoughts?
That’s a beefy Karcher, however you’re right, definitely the more flow the better. I think you usually need to look for around the 13L mark and over 3000psi. I wouldn’t call my particular Pressure Unit professional, it’s a knock off Honda unit that’s imported by a local machinery joint in my state. The attachment itself is great due to its quality cast and long lasting carbide tipped nozzle. The golden Amazon cheapies are a glorified suction feed squirty bottle.
Hi there, US, Aust or elsewhere? I have a couple of links in the video description. eBay link is for Australia (cheapest) and I have filtered through Amazon US for the right one. Cheers
Hi guys, new to this so dont go too hard on me! I have updated the description with a couple of Amazon links for the exact product I bought. Hope this helps and sorry for the inconvenience.
Hello..how can you assist me to get this product to me in Cape town south Africa...ebay and Amazon dont ship to this country...I have ask my son in new Zealand also. But no shipping there too.thank you.
They both have their pros and cons. This setup is also messy, loud and the flash rust is a problem. Wet sand lodged in crevices can be problematic also.
If it works as good on larger subjects than it does smaller parts, then blasting most of a car could be a possibility! By the way, is a KE17 SL those fastback Corollas?
you said yours sandblaster was for 3000psi but the ones you have listed are for 5000psi are these the exact same as what you used or are they different
I think you will find the nozzle is rated to a maximum of 5000 psi. My pressure washer is 3000psi or so. But it’s the gallon/ liters per minute flow which is most important to make the nozzle work best
is this the exact one you used and NOT THE BRASS ONE Premium Tungsten Carbide Nozzle Cone, Stainless Steel Nozzle Tip 4.0 and Steel Head for Durability and Excellent Performance
Nice job but if you did not name the product it doesnt do us any good , Just put up a link and we can purchase. I have a 4400 psi 4 gpm pressure washer and would like to do my car hauler. Send us a link. Thank You
A traditional review yes, this is just me showcasing a new toy. I’m not affiliated or sponsored by anyone, nor did I get permission from the company to name them/ provide links. Simply there are 2 types that are found, brass cheap version and this style. I went for the latter. Cheers for the feedback and in the future if I ever do proper reviews I will link the item.
@@PangazShed Nice display of what you found, and always ignore the Muppets that seem to be everywhere on youtube wanting a "Hollywood production" and all the info. for no cost or effort from them, if they have google they can find it if they tried.
Rust after blasting can be easily dealt with.. Better than hours grinding or brushing just to end with a mediocre job. Not counting that there are additives for rust prevention in wet blasting.
@@PangazShed REALLY? You sound perfectly Aussie when you speak! Welcome! I was wondering why you seemed so good natured and humble. Because your mind is still resisting our indoctrination. Do not resist, Panga. Join us. "Give Way" means "Look out d*ckhead", "Sick Day" or "Personal Day" means "CBF Day".. "Written Warning" means "Stress Leave", you'll get the hang of it.
![ALLY - OH MY! [ REACTION ] 'Amarin Nitibhon' #ALLY_OHMY #ALLY #allynitibhon #แอลลี่](http://i.ytimg.com/vi/nX9qpHjVfbQ/mqdefault.jpg)
Nice, does an amazing job.. That ke10 Bay is going to turn out sweet!!!
Thank god, finally someone who uses the bloody thing and gives some decent footage and feedback.
I can finally buy it.
Good stuff! I don’t care what anyone says, better than a pressure pot sandblaster in so many ways, provided the pressure washer is decent. I done a whole engine bay if you haven’t already seen. Works great! Thanks for watching!
Really great results! This is the best I have seen. I noticed that these particular blasters need 4gpm to work. I was all excited until I found out my pressure washer only does 2.5gpm. So, a high volume pressure washer is a must. The extra water flow you added from your source made all the difference because your pressure washer can handle the volume needed. Great video!
Just picked one up today at northern tool . i hope it works half that great. enjoyed your video great job
Cheers mate!
Well? How did it turn out?
Awesome work, that cleaned up very nice , thank you for your time and effort.
That works awesome!
Thanks for sharing.
Great video which I watched after total frustration with my $50 amazon purchase.of a water blaster attachment - it seems my professional Karcher 5/12C. You definitely made the right decision investing in professional grade equipment to avoid pitfalls.
Looks like you need to spend a grand to achieve top grade professional results. (as usual).
My Karcher apparently hasn't got the guts to create enough suction to transport the media. from the bag (80 Grit Garnet purchased from H&F) to combine with the jet stream.......
Based on your set up the karcher flow rate is probably too low at about 10l/min and 2200psi.
Your thoughts?
That’s a beefy Karcher, however you’re right, definitely the more flow the better. I think you usually need to look for around the 13L mark and over 3000psi. I wouldn’t call my particular Pressure Unit professional, it’s a knock off Honda unit that’s imported by a local machinery joint in my state. The attachment itself is great due to its quality cast and long lasting carbide tipped nozzle. The golden Amazon cheapies are a glorified suction feed squirty bottle.
Where can you get this setup of all the videos i watched this setup worked the best and i do believe a lot had to do with the bigger gun thsnks
Hi there, US, Aust or elsewhere? I have a couple of links in the video description. eBay link is for Australia (cheapest) and I have filtered through Amazon US for the right one. Cheers
Hi guys, new to this so dont go too hard on me! I have updated the description with a couple of Amazon links for the exact product I bought. Hope this helps and sorry for the inconvenience.
Hello..how can you assist me to get this product to me in Cape town south Africa...ebay and Amazon dont ship to this country...I have ask my son in new Zealand also. But no shipping there too.thank you.
Great video !!! That worked bloody good !
Great tool no doubt. Better than using an air compressor and dry blasting.
They both have their pros and cons. This setup is also messy, loud and the flash rust is a problem. Wet sand lodged in crevices can be problematic also.
hello, do you also have a link for Europe where to buy? thanks!
Excellent video
It did seem to be losing water you could tell the flow started good and droped
OATH! does a great job.
Can you use soda thru it instead of sand?
I'm going to be doing engine parts and don't want to chance sand particles getting lodged.
Thanks
Not sure to be honest! If the soda can be pulled via suction feed and the attachments nozzle is fit for purpose then I don’t see why not. Cheers
Thanks my friend! Take care
Mad purchase. So handy to have. I want one now
Get on it!! Problem is, running out of things to blast!
@@PangazShed come and blast my KE17SL.
If it works as good on larger subjects than it does smaller parts, then blasting most of a car could be a possibility! By the way, is a KE17 SL those fastback Corollas?
@@PangazShed yes. 35mm lower roofline, 2 door, full Japanese import.
Awesome, remind me of a TX Gemini coupe! Very nice 👍🏻
you said yours sandblaster was for 3000psi but the ones you have listed are for 5000psi are these the exact same as what you used or are they different
I think you will find the nozzle is rated to a maximum of 5000 psi. My pressure washer is 3000psi or so. But it’s the gallon/ liters per minute flow which is most important to make the nozzle work best
Any links to see if I can buy exactly the same attachments you used in this video
Please
Please check the description for the links, Thanks!
Where can I buy
From What website did you buy it and what is the name of the product???
Please check the description for the links, Thanks!
Morning from South Africa.
Could you please forward me the make or link from amazon for the adaptor.
Please check the description for the links, Thanks!
How much sand did you go through just on that part?
Not much, maybe a couple of kg’s. I did a whole engine bay with about 1 and a half bags. Hope that helps.
is this the exact one you used and NOT THE BRASS ONE
Premium Tungsten Carbide Nozzle Cone, Stainless Steel Nozzle Tip 4.0 and Steel Head for Durability and Excellent Performance
You haven’t put up a link, but going by the description, yes that’s the one.
@@PangazShed thanks mate appreciate your help
be nice, to have a link to it bro
Please check the description for the links, Thanks!
Nice job but if you did not name the product it doesnt do us any good , Just put up a link and we can purchase. I have a 4400 psi 4 gpm pressure washer and would like to do my car hauler. Send us a link. Thank You
Please check the description for the links, Thanks!
If your going to review a product you should atleast put a link to the product
A traditional review yes, this is just me showcasing a new toy. I’m not affiliated or sponsored by anyone, nor did I get permission from the company to name them/ provide links. Simply there are 2 types that are found, brass cheap version and this style. I went for the latter.
Cheers for the feedback and in the future if I ever do proper reviews I will link the item.
@@PangazShed liked your video.. Don't worry. Talking about entitlement! 🙄
@@PangazShed Nice display of what you found, and always ignore the Muppets that seem to be everywhere on youtube wanting a "Hollywood production" and all the info. for no cost or effort from them, if they have google they can find it if they tried.
Perge the line before you start
that looks fucking awesome. unfortunately i dont think my K2 karcher is strong enough lol.
Sandblasting better to use without water cuz water levels rust after
“Dustless Blasting” is a thing. It uses water mixed with blasting media. There are products to overcome the “flash rust” issue, no problems! Thanks
@@PangazShed what is the kit called
Pressure Washer Santblasting Attachment (or Nozzle)
Rust after blasting can be easily dealt with.. Better than hours grinding or brushing just to end with a mediocre job. Not counting that there are additives for rust prevention in wet blasting.
Only ones I can find come from America with a $400 postage bill .. I'm not going to pay that .
Have you tried my link in the description? It’s $130 plus postage, if you are in Australia. They might ship elsewhere but you would have to ask.
Good and thank you, however could you get to the point straight away.
Chewing for that long that simple stuff just doesn't make sense.
Thanks for the feedback. It seems some people like lots of detail some people like none. In the future I’ll make 2 versions
its AND OR.. Don't muck with the system mate. We don't need more OR AND separatists trying to start a civil war here.
I take it you’re talking about Australian English? I’ve only been in this country a couple years, my apologies
@@PangazShed REALLY? You sound perfectly Aussie when you speak! Welcome! I was wondering why you seemed so good natured and humble. Because your mind is still resisting our indoctrination. Do not resist, Panga. Join us. "Give Way" means "Look out d*ckhead", "Sick Day" or "Personal Day" means "CBF Day".. "Written Warning" means "Stress Leave", you'll get the hang of it.
Strewth!
Blah blah blah, get on with it..