Yes! It worked! Followed your instructions to every detail... et voila! The image of my zino pro + is back again! Your my hero! Thanks a lot for the help. Couldn’t have done that without you.
Very valuable video!! Thank you! I had no connection and no FPV so I ordered an image cable as per your advice. Took a few weeks to come in but with your video it only took minutes to replace! Connects fine now!
Welcome back Chris. Thanks for another informative Zino repair video. I've had my Zino Y for about 10 months now and so far no problems but I still download all you videos (just in case) !!!!
Hi there! Thanks for all your zino videos. Very interesting stuff! Currently I am having a 0x0081 error on my gimbal. Do you have any idea what the problem would be?
I don't even own a Zino but I am here for you Chris...and the free beers! blessing brother from the Chiclotin, good vibes and appreciation for all you do, may the days treat one and all with kindness eh, see you all next video! 8^)
Great video! I have an issue with calibration failure (0x0080), video works fine but the gimbal control doesn't work and video is jittery. Do you think it needs a new motor cable? Thanks!
Did a calibration by hand just to see what it could be - managed to get the ‘angle tilt is too much’ now so I’ve ordered the proper gimbal calibration tool and hoping to do the calibration once that’s here. Thanks again!!
Hey Chris. Welcome back. Good to have you back on line. Can I ask a question please. Do you know if it's possible to disassemble the camera housing on the fimi x8 se 2020 in order to manually rotate the lens like you can do with the zino and zino Pro to fix a badly focused lens? Any thoughts? Thanks for any insight and God bless.
Hello! Hope you see this and can maybe lend some advice. I bought a Zino Pro Plus a bit back, but didn't fly it right away. When I did, I thought it was awesome. Took a break and then went to fly it again and while about 20 feet in front of me and about 15 feet up the motors just stopped and it dropped to the ground. I did hear something about usb connection right as it happened. Long story short, I found that the controller was bad (would charge but not turn on). I then bought a zino pro drone, controller, etc. hoping to use the controller and also get another drone out of it. What I found out was that the camera on the zino pro did not work. I also found out that the x-hubsan 2.0 app no longer worked and wanted to do an update but then threw out errors that it couldn't do anything. I am addressing one thing at a time. Any ideas about the 2.0 app? No matter where I get it from, it gives me the same error AND it also says that the app is not compatible with the device via usb. YET, no problem when using the x-hubsan app for the zino pro. As for the gimbal and camera - is there any way to test these to determine if the camera itself is bad or a ribbon or ???? Thanks!
Dear Chris! I have replaced te cable based on this excellent video but the problem is the same unfortunately. I have a solid red light at the side of the quad and no connection after refreshing, just timeout. Don't you have any other idea to solve the problem? Thank you! :)
A solid red light is no connection or leas transmitting a signal. The leas repeater under the main board in front of the fan could be fried or a connector issue there.
Hey Chris, the time and work you put into this and other DIY videos are extremely helpful, and I'm sure I'm not alone when I say, "thank you, we appreciate them." The drone in this video, do you recall the model? I have a Pro +, I just took it apart and it looks different than the model you used in this video. Improved design and some additional components, but it's not hard to recognize the design also serves another purpose...makes it easier for Hubsan to determine whether a DIY had been attempted on the drone. Just FYI, no pun intended.
Hello Chris ! Do you somehow know where I can find a Camera module(no Gimbal) for the Zino Pro ? Thank you and keep the good stuff going Greetings from Germany
My camera image does not want to display on my screen. The drone flies but I can't get an image on my phone. It just shows black on my screen. I have replaced the cable but it still looks has the same problem. Black screen. It was working fine until the gymbal cover got stuck and when I removed it that's when I lost the image. I'm getting frustrated with it all ready. Can you please tell me what to do to fix my problem. Thank you. Love your videos very helpful
Most likely it still is a result of the cable. If that was the original problem for sure then you could have made s mistake in installing the new one or you got a faulty one. Post in my group if you need further help. 👍🏻 facebook.com/groups/HubsanQC/
i would like to send you some footage from my Zino Pro. Please let me know if the video quality is good enough or do i need to replace my image cable or could it be something else
Good to see you back! Great tutorial video Chris! Hope I never have to do this to mine but it’s good to know that I can always come to this video for the step by step instructions on how to do it. 👍🏻👍🏻
Hello. Great video. My zino pro today gave me a problem. Whe. I tried to use it all worked properly, as usual, but no video was presented in the phone. I tried several things: another usb cable, reinstall the apk...but nothing. The gimbal seems to have a little vibration and no video is displayed. The drone has not crashed never and it has always the gimbal protector. Maybe is one of those cables? Thanks and regards
@@QCGUYthanks for the answer, can I put a fan in the zino "Y"? I saw that the board (other than zino1) has an unused connector (I think), logically it would make a different upper chassis
I assume you mean the image cable? Go to AliExpress and search zino image cable. I don't post the link for this because they have different sellers that come and go so the links die out. Search.....you'll find it.
Hello i have a hubsan zino pro. first there was no problem with flying the drone but now i cant start the drone he says the horisotal calibration is failed i have done the calibration a several themes but it wont help.
Hi, my zino pro show can't format sd card(sd card is notmal) , and have no fpv signal and image. Is it the image cabel damaged? or what happen for my aircraft? thanks.
@@jomngail original Zino (wifi) red flashing light can be a camera issue not the motor cable. If the camera image cable is bad then you won’t have wifi and you get a red flashing light. The cable can look perfectly fine but still be bad.
Thanks for your comments. I will try replacing the lmg cable. But it looks a daunting task. Hope I can do it. Will get back to you when it's done. Tqvm once again for your unselfish help
I do repairs everyday of the week and I do these in my sleep so absolutely. The part number is ZINO000-81 for the image cable and ZINO000-80 for the gimbal cable.
Yes! It worked! Followed your instructions to every detail... et voila! The image of my zino pro + is back again! Your my hero! Thanks a lot for the help. Couldn’t have done that without you.
That makes me happy 😊
This is why I put these videos out there 👍🏻
Very valuable video!! Thank you! I had no connection and no FPV so I ordered an image cable as per your advice. Took a few weeks to come in but with your video it only took minutes to replace! Connects fine now!
That's what I like to here...My efforts help some so this is nice to here. Thanks
Welcome back Chris. Thanks for another informative Zino repair video. I've had my Zino Y for about 10 months now and so far no problems but I still download all you videos (just in case) !!!!
Thanks a lot! Zino deserves to live again!))
Thanx a lot QC guy,
I have replaced image cable and wifi issu solved, 👍👍👍
🧡🧡🧡✌🏻
Hi there! Thanks for all your zino videos. Very interesting stuff! Currently I am having a 0x0081 error on my gimbal. Do you have any idea what the problem would be?
Is the gimbal twitching on start up or just dead?
Thanks to Chriss I have a picture on the camera again! You're very good.
🧡
I don't even own a Zino but I am here for you Chris...and the free beers!
blessing brother from the Chiclotin,
good vibes and appreciation for all you do,
may the days treat one and all with kindness eh,
see you all next video!
8^)
Great video! I have an issue with calibration failure (0x0080), video works fine but the gimbal control doesn't work and video is jittery. Do you think it needs a new motor cable? Thanks!
Try the gimbal tool computer calibration first. That is generally what 0080 means.
If that fails then yes do the cable. 👍🏻
Did a calibration by hand just to see what it could be - managed to get the ‘angle tilt is too much’ now so I’ve ordered the proper gimbal calibration tool and hoping to do the calibration once that’s here. Thanks again!!
If the gimbal is just floppy and image is gone do I need to replace both image and gimbal ribbons? Thanks for the video.
Often yes that’s the case or a bad board.
good morning friend
Would you know where I can buy only the hubsan zino pro plus guimbal camera plate?
Please send me the link if you know, ok.
Never seen the back plate for sale sorry...
Hey Chris. Welcome back. Good to have you back on line.
Can I ask a question please. Do you know if it's possible to disassemble the camera housing on the fimi x8 se 2020 in order to manually rotate the lens like you can do with the zino and zino Pro to fix a badly focused lens? Any thoughts?
Thanks for any insight and God bless.
I don't know for certain but most do so as a guess I would say yes.
@@QCGUY Thanks for the reply. Welcome back again.
Not easy at all ! Good job !! 👍👍
Hello! Hope you see this and can maybe lend some advice. I bought a Zino Pro Plus a bit back, but didn't fly it right away. When I did, I thought it was awesome. Took a break and then went to fly it again and while about 20 feet in front of me and about 15 feet up the motors just stopped and it dropped to the ground. I did hear something about usb connection right as it happened. Long story short, I found that the controller was bad (would charge but not turn on). I then bought a zino pro drone, controller, etc. hoping to use the controller and also get another drone out of it. What I found out was that the camera on the zino pro did not work. I also found out that the x-hubsan 2.0 app no longer worked and wanted to do an update but then threw out errors that it couldn't do anything.
I am addressing one thing at a time. Any ideas about the 2.0 app? No matter where I get it from, it gives me the same error AND it also says that the app is not compatible with the device via usb. YET, no problem when using the x-hubsan app for the zino pro. As for the gimbal and camera - is there any way to test these to determine if the camera itself is bad or a ribbon or ???? Thanks!
Hello, I want to say great video and you got skills. I was wondering how to have you fix my zino pro? I know you mentioned it in the video.
Thanks…I fix them regularly and have most parts on hand. You can email me @ qcguy.chris@gmail.com
I emailed you. I was wondering if you received it?
@@haydenphox326 Yes I’ll respond after work 👍🏻
Dear Chris! I have replaced te cable based on this excellent video but the problem is the same unfortunately. I have a solid red light at the side of the quad and no connection after refreshing, just timeout. Don't you have any other idea to solve the problem? Thank you! :)
A solid red light is no connection or leas transmitting a signal. The leas repeater under the main board in front of the fan could be fried or a connector issue there.
@@QCGUY Thx! Can you show me the part on a picture?
@@groffelfoldi a.aliexpress.com/_mLL0vXl
Great video! It is hard for our sausage fingers to do what those small Chinese fingers do!
Hey Chris, the time and work you put into this and other DIY videos are extremely helpful, and I'm sure I'm not alone when I say, "thank you, we appreciate them." The drone in this video, do you recall the model? I have a Pro +, I just took it apart and it looks different than the model you used in this video. Improved design and some additional components, but it's not hard to recognize the design also serves another purpose...makes it easier for Hubsan to determine whether a DIY had been attempted on the drone. Just FYI, no pun intended.
This one is a pro. The pro plus isn’t much different just very slight change in hardware.
thaank you very much . i do it and zino still live
Hello Chris ! Do you somehow know where I can find a Camera module(no Gimbal) for the Zino Pro ?
Thank you and keep the good stuff going
Greetings from Germany
I have one left but it's best to message me on facebook under QC Guy or my listed email on this channel. Thanks
which drone do you work on the least?
Out of the Hubsan Zino models it would be the Zino pro. I work on others as well but most everyone comes to me with Zino’s.
Where can you get the back cover plate that goes over the image/motor cables (3:50 in video) ?
Can’t
My camera image does not want to display on my screen. The drone flies but I can't get an image on my phone. It just shows black on my screen. I have replaced the cable but it still looks has the same problem. Black screen. It was working fine until the gymbal cover got stuck and when I removed it that's when I lost the image. I'm getting frustrated with it all ready. Can you please tell me what to do to fix my problem. Thank you. Love your videos very helpful
Most likely it still is a result of the cable. If that was the original problem for sure then you could have made s mistake in installing the new one or you got a faulty one.
Post in my group if you need further help. 👍🏻
facebook.com/groups/HubsanQC/
i would like to send you some footage from my Zino Pro. Please let me know if the video quality is good enough or do i need to replace my image cable or could it be something else
Upload something on your channel 👍🏻
Send me the link...
Good to see you back! Great tutorial video Chris! Hope I never have to do this to mine but it’s good to know that I can always come to this video for the step by step instructions on how to do it. 👍🏻👍🏻
Hello. Great video. My zino pro today gave me a problem. Whe. I tried to use it all worked properly, as usual, but no video was presented in the phone. I tried several things: another usb cable, reinstall the apk...but nothing. The gimbal seems to have a little vibration and no video is displayed. The drone has not crashed never and it has always the gimbal protector. Maybe is one of those cables? Thanks and regards
Yes its most likely the image cable. They are my most common repair when people send me their hubsans to fix.
Hi Chris, the ESC of zino "1" is the same as that of zino "Y" apart from the color of the cables, I want to change arm the zino 1 at zino Y
Yes it’s the same esc’s 👍
@@QCGUYthanks for the answer, can I put a fan in the zino "Y"? I saw that the board (other than zino1) has an unused connector (I think), logically it would make a different upper chassis
@@franp.3824 sure you could simply by putting it in the same location as it is on the pro and tapping into a safe 5V location.
Hi bro...
I have problem with my hubsan zino pro.
Aircraft dissconnecting.
Can you help me what's problem with this?
Share it in my group and we'll see if we can sort it out. Thanks
facebook.com/groups/HubsanQC
Hi how can I buy this product
I assume you mean the image cable? Go to AliExpress and search zino image cable. I don't post the link for this because they have different sellers that come and go so the links die out. Search.....you'll find it.
Hey I have a zino pro + that fell out the sky due to bad battery connection I was wonder could we link up and maybe u could fix it for me please
Sure you can email me and I’ll give you my shipping address.
qcguy.chris@gmail.com
Where abouts are u located
@@robbieyerly6448 PA
Hello i have a hubsan zino pro. first there was no problem with flying the drone but now i cant start the drone he says the horisotal calibration is failed i have done the calibration a several themes but it wont help.
Sorry, I can't troubleshoot your problem here which is why I have a group. Thanks
facebook.com/groups/HubsanQC
Hi, my zino pro show can't format sd card(sd card is notmal) , and have no fpv signal and image. Is it the image cabel damaged? or what happen for my aircraft? thanks.
Most likely the image cable yes. It can effect both the issues you have.
@@QCGUY thanks.
I have wifi connection problem. Checked the motor cable. No defect. Please advise. Tqvm
On which model and when you have everything on what color is the light on the side by the sd card slot?
Sorry. It's zino. Red colour, blinking
@@jomngail
original Zino (wifi) red flashing light can be a camera issue not the motor cable.
If the camera image cable is bad then you won’t have wifi and you get a red flashing light.
The cable can look perfectly fine but still be bad.
Thanks for your comments. I will try replacing the lmg cable. But it looks a daunting task. Hope I can do it. Will get back to you when it's done. Tqvm once again for your unselfish help
@@jomngail I have a video if you didn’t know… 👍🏻
im getting an error code 0X2000 on my zino pro plus. can ya help me?
It’s not always the same exact situation with codes. It’s best to show what the gimbal is doing or not doing.
facebook.com/groups/HubsanQC/
Why no camera image on my zino pro cable?
Broken…buy a new cable
What are the part #’s for the cables? can I ship you mine and you repair it, please? lol I have a pro +
I do repairs everyday of the week and I do these in my sleep so absolutely.
The part number is ZINO000-81 for the image cable and ZINO000-80 for the gimbal cable.
@@QCGUY where are you? i’m serious about shipping mine to you. what is your repair rate?
@@travelingtrainers8372 I’m in Pennsylvania..
Email me: qcguy.chris@gmail.com
link