Traxxas Revo 3.3 Turning the needles to basic factory setting Nitro Engine dont start
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- RC USA 201 and RC KING KONG. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RC KING KONG and RC USA 201
#revo3.3 #tningrevo3.3 #nitroengine #revo3.3nitroengine, #nitrorevodontstart #revo3.3basesetting #nitroenginebasicneedlesetting
Thank you sir I did exactly what you said it’s running like a champ. I got a Traxxas slayer off of one of my friends he sold it to me pretty cheap only 200 bucks. He said he havent ran it in two years. I replaced the spur gear. The slipper clutch after watching your video. She fired right up cant believe how good it’s running.
Nice job
Great video, only one I have seen where they tell the exact starting position for the Low Speed Needle! I used this video earlier today to reset my Revo settings and get it running again! Worked like a charm! I only had to do some minor adjustments to lower the idle a bit, and richen the High Speed Needle half a turn, due to my 25% nitro fuel
Nice job!!! It always worked for me
You are the man dude thank you so much couldn’t get mine to start and run properly to do the break in they say it’s rt r/break in out of the box and everything was all funky I appreciate it man! Now it runs good and I can finally break mine in.
Thanks I been looking to buy one of these for a long time but always felt like it would be hard to deal with. Saving this video for future reference.
Thank you boss! I got my jato back and running!
Nice job!
Thanks for the good tips on how to set the high and low speed needles only bought the traxxas slayer pro 4x4 yesterday and can't wait to get it out for a spin thanks to you bud big thanks and a big like from me bud 👍🤝
Great job, bro!! Came in handy!! 😎👍
Thx for the ni e video got one bearly used and is to rich and now i have a hood place to start
You saved me thanks man I taught adjusting the trottel linkage will fix my high idel and overheating overall but when I slapped this setting on my t maxx it was running really crisp and clean came un clutch thank
I blew my first plug barely running it still new finally got it to shift if this video and one other but now I think I'm a bit rich or lean not sure assuming to much fuel cuz I got alot of drips that come from exhaust drips not alot but not sure what's best
Video was so perfect I had to subscribe lol 👍🏾👍🏾👍🏾🤣🔥🔥🔥I have mines “lo
I have a 2.5r....it sat for over like 10 years. It will run but im thinking the rings are bad on the piston.. onky runs for about 10mins and than replace glow plug.. think its junk or need better tuning? Freaking glow plugs are to much for 10mins
I think this is junk
@rcusa201 agreed got a 3.3 otw
What is the throttle and brake servo you running I see there different ones in different revo's
Stock
This video will help me out when I get a 3.3 engine but I have a question can you please make a video on tuning a .15 and the .18 and .16 and I think there’s a .15 sh engine I bought a nitro stampede vintage four or five years ago and could never keep it running so it just sits on the shelf and I don’t know how to turn it but. If you could make them videos on tuning them engines that would help me a lot thanks
Sun have those
@@rcusa201 what do you mean
Boss man whats best glo plugs for 20 percent nitro for the revo 3.3
I still with stock
I though i.cooked my engine here the bearings lock up in the clutch bell burnt up 2 clutches
I got a new 3.3 engine the low speed was at 1.5 factory.
Ok I’ll try that
@@rcusa201had my high side at 3 turns out and it was gurgling to rich right now I'm at 2 out and still playing with it
What kind of rc is this i have the same model but cant find the parts manuel
Traxxas Revo 3.3
Where do the double a batteries go for the controller to control the wheels?
The what
@@rcusa201 I'm sorry. Never mind. I found out the model Revo I have, has a recharge port at the bottom of the frame. I have to order a charging cord to charge my Revo so that the receiver will control the wheels. If that makes any sense at all to you, I'm just getting into this hobby
@@rcusa201 thank you for responding
How do I know when the idle gap is .7- 1.0 mm gap
@@williedoit3381 I mean I thought it was right but my idle screw is all the way down to where it won’t go further but it looks like that
What are you showing other than your idle is WAY too high
Mine NEVER starts that easily 😢
Retune it
Good fuel, good glow plug, and a good carb setup (needle base settings to start, no air leaks, etc) it’ll start every time. Set idle gap and turn low speed to achieve idle.
assuming good compression @@gforce_117