Thank you so much for the love and support on my channel! If there is anything you wish to see next, let me know here in the comments. If not, just comment your favorite emoji that comes to mind when you watch my vids. :)
Bought this, set it up and am enjoying it ..... one question or troubleshooting help item. My pump seems to be working well (plenty of flow into chiller when I disconnect the "in" tube to check).... but I am regularly having trouble getting the water from the chiller back into the ice barrel. I have "purged the line of air", sort of checked all, etc.....is there a setting on the chiller that could be causing this that I am missing? Any help or suggestions are appreciated. Keep up the good work promoting what I think is a good healthy habit! Thanks!
@@DavidMausJr well I forgot to add your code. Then they never answered me to add the code in. It’s been several weeks. Zero reply to emails. Don’t think i will be doing business with them again. Never heard of a company taking weeks to answer support emails.
Hi David - Excuse me if this was already addressed; why is there a need to have a separate water pump, aside from the chiller? I've seen other chillers without external water pumps. Secondly, how do you sink up the water pump and the chiller from a power perspective or are the pump and chiller always plugged in and turned on?
I tighten the screw that connects the barrel to the filter too tight and now the tube is cracked inside the barrel and leaking. Anyone know where I can order a new part?
Loved the video and the clear, concise instructions for adding the various components. Do you have a suggestion for a cheaper alternative to the IB300? The Ice Barrel is out of my budget range at the moment, but I would like to use your 1/4 HP cold plunge kit with a more affordable tub/pod. Keep up the great work with the channel!
I purchased the pump you link to but the inside female end is 5/8, not 3/4. I am struggling to find a 5/8 to 3/4 coupling to connect the pump to the filter.
@@DavidMausJr Have everything setup properly, as in the video, though using 3/4 barb for slightly smaller hose (which I had in my old DIY and worked fine). Small leaks under intake from filter to pump, even though I have plumbers tape on each end. But my biggest concern is there is very little suction. The pump is trickling water through the chiller. My last DIY used a small pool pump and had plenty of power, but this pool pond pump feels weaker than it should be. At a loss, as I used to use a pond pump on my last one to drain water whenever I cleaned it out and it seemed to have more power/suction. At a loss here.
You had two answers on how to add drain outlet to keep water from going on floor when draining. You recommended faucet splitter or a pvc tee. Not sure which one would be better and no clear about how to use the tee. The faucet splitter would have the pump and strainer at an angle when connecting. Possible to do a short video about this? Thanks
Just curious why you choose not to use a filter. I know the strainer sort of acts as a pre filter but every other set up I’ve seen has a filter as well. Thanks!
Glad you asked! The filters are just another monthly cost and they are going to get nasty. i use the Ice Barrel Stabilizer which works great plus i have a portable ozone machine i use in all my plunges about once a month. My water stays clean and clear without needing any extra stuff but people do go that route too and its great! I just like simple. The strainer keeps debris out of the pump and chiller and works just fine :)
Hey David, I got the 1/4 horsepower Amazon kit and 1 thing you would have to change is for the pump that was in the Amazon kit it’s afapate is 1/2 not a 3/4, everything else was right tho I just have to get a 1/2 to 3/4 adapter at lowes
Love your videos! I know in your other videos you mentioned that there's a possibility that the inline pumps can burn out, I was wondering if you experienced that with an Active Aqua water pump or was it a different brand? If so, how long did it take for it to burn out?
Switched to Danner pumps, they are little beasts. Yes they could all theoretically burn out if they were on for a while with no water in the line. That is the main concern
The male thread to male thread, where it connects to the pump keeps cracking and leaking water. Think it’s due to the weight of the pump not leaning on anything. This has been my second pump that’s cracked…
You got it! Super simple, all you need to do is fill the barrel up with water and look for water to enter into the strainer, if you dont see water, open up the hose to let teh air out. The goal is to make sure water is in the pump.
You said a “strainer.” Is that the filter? How long does the water stay clean? How often do I need to dump and refill with new water? Chlorine? I want to do this but I don’t know how long the water is going to stay clean and what to treat my water with.
The strainer filtered almost exactly what a 20 micron filter will, it doesn’t need replacing. Water will stay as clean as you keep it clean. People use chemicals but I tend to just use hydrogen peroxide and occasionally ozone. Water stays clean for Months.
I’m using Active Aqua submersible pump AAPW800 and I’m doing the 1/2 go chiller with 3/4 connections. But when I open the pump to attach the strainer the pump inner thread is slightly smaller than 3/4”. Any thoughts? Thanks!
That was my concern with offering options. You will need to get a converter, the tip might be a 1/2" so you might need to order a 1/2" to 3/4' inch adapter or run it to home depot. If you can, send me a pic on IG @dmausjr
Did you ever figure out a solution to this? I’m having the same problem. The 3/4 is slightly too big. And the included piece that does screw in perfectly has a barb that is too big for my 3/4” hose. Super frustrating.
thanks so much for all the help! I ended up buying the 800 gpm pumps and the front cover had a 5/8 thread rather than a 3/4. Did this change since the video was made or should I have gotten the 1000 gpm pump?
Hi David. Thanks for this video as this is very thorough indeed. However, I've run into an issue where my 3/4" male adapter is not able to connect to the pump. I've tried numerous times and 2 unique 3/4" male adapters but to no avail. These same adapters have no issues connecting to the strainer on either end so I'm a bit lost here. I'm curious but I just checked my pump and it is the Style: 800 GPH model. Is it mandated I purchase the 1000 GPH model instead?
Ok just following up here but the 800gph pump has a 5/8" thread after noticing another hose fitting I was able to connect. I've submitted a return to Amazon and hoping the 1000gph pump model will have 3/4" female threading to fit the 3/4" male adapter.
Yes, thanks again @@DavidMausJr all squared away so now just wait for the barrel arrival tomorrow and the pump on Wednesday. I should be good to start cold plunging this week, thanks to your reviews
@@DavidMausJr thanks. And last question then I swear I’ll leave you alone. Although I live in Texas, it’s supposed to be down in single digits and my chiller is out side. You think that will be an issue or should I dc it and bring the chiller inside
Let's say we have a week or 2 where the ambient temps outside are in the 40's. Can you use pump only to keep the water moving through the 'off chiller' Orr if we're plumbed through the chiller, it needs to be running? If it needs to be running, you would just shortcut the system with pump only flow during colder temps no through chiller, yeah?
I think me and 10,000+ other people who have had their active aqua chillers outside in the elements since day one would say you are absolutely fine with them outside as they are. Obviously do so at your own risk... but Plunge used active aqua for years before making their own new chiller and they are all doing great outside. Active Aqua needs to make some changes to their recommendations
Hi I just received my ice barrel three hundred, I bought a intex filter via Amazon. I’m a little confused with setting it up. I can be reached and I’m in south Florida. 😊
Thank you for putting this together, great setup. I have been running for the last two months without issues but recently the filter just stops pumping water after a while which I assume is due to air build up. I primed it by filling the tubes with water and that seems to work for about a day and then the same happens again. Am I doing something wrong and is there a good solution for this? Thank you
I appreciate you creating this video as it clarifies my questions before investing in a "Cold Plunge". Thank you for creating such informative videos. Your content is truly helpful, and I hope you will continue to produce more of it in the future.
David, I got the 800 pump and I'm using 3/4" tubing and everything. I got 2x 3/4" x 3/4" fittings to link the strainer and the pump together, but my 3/4" fitting won't fit in to the 800. It looks like I need 3/4" to 5/8"
Oh no! Yea the 800 might be a smaller hole. I use the 1100 and it comes with the right pieces. So sorry my friend. But you should be able to get that cheap on Amazon
so you found that you didn't need any Teflon tape or o-rings on any of the fittings that you screw in that are from leaking or slightly dripping? also all fittings that were PVC like this for just hand tighten you didn't need tools to stop them from leaking etc.. I imagine over-tightening is worth cuz you could crack the plastic? thanks so much for your help and and videos
Thanks for the support and question. I didn’t use any tape, but it could help if needed. I also hand tighten almost everything, but I used a wrench a few times but not to over tighten, just to make it easier.
Think a 1/2 HP paired with the 300 can hang for the stupid hot summers in Phoenix? Or is it best to go with more horses? It’ll be under the patio, but outside will still be a brisk 110°.
Thanks for the video. I ordered my Ice Barrel 300 back in August but haven't received mine yet. In fact, I've tried contacting Ice Barrel multiple times through multiple channels to get an ETA and they won't answer me.
Oh man i am sorry about that! I know when i was at the HQ they were slammed with emails about shipping and they are a small team (currently building and growing). They were like "man i want to respond to each and every email about the shipping, but that would take hours and in that time i could also just process the shipping... dont want to make people mad but im going to just ship them their barrels." not word for word but i agreed. Its coming soon and i hope it comes sooner my friend.
So that pump is a submersible pump, but you can use it out of the water, and it won't burn up? Also, does the 3/4 adapter come with the pump once you remove that filter cover on the pump? You went over that part kind of fast. Thanks brother :)
If there is any advice I can give to anyone wanting to do this DIY, please dont go with any less than the 1000 gph pump. The fittings are all different on the smaller ones.
My 300 came with a faucet and I'm having a hard time removing it so i can use the 3/4 adapter to connect to the rest of the setup. I'm hoping the faucet can be removed somehow
It should just unscrew. It might be on tight. Or yes you can use everything and just connect to that hose bib it will just angle down and might not work perfect. Play with it and let me know. Feel free to message me on IG @dmausjr and i will help you through it
I found your Amazon DIY list for 3/4” setup!! That’s awesome. You mentioned an ozonator in the video. I saw the green water killer on the Amazon page, but not sure that’s it. Hoping to locate something next to the pump and chiller setup which will be about 15’ from the Barrel. Any recommendations for some type of inline sanitizer? Thanks, David!
I put in a UV green killing machine light in my plunge use hydrogen peroxide and water barrel stabilizer, do I need like a marine land water filter in my ice barrel too? I have this exact setup with strainer and all
hi david , is i have the 1/2 hp chiller , will the 3/4 tubing will fit in the top part of the pump trough the chiller ? i think i heard you saying that the top tub attached to the pump is 1 inch ?
Hey David! Thanks for sharing your processes with us. I just followed the exact steps to install an active aqua chiller to my IB 300. Does the strainer get filled to the top when its facing up like that? Mine is only filling up just a little bit so I'm not sure if it's actually filtering the water. Thanks!
Love your videos! So I put together the kit and cracked the lower threaded plug. How do you order parts from IceBarrel? I put in a support ticket and tried to use their chat feature on the site but no luck.
add a quick connect adapter to the release valve part and just quickly disconnect the chiller /pump assembly and empty water to refill the designed way
What do you think about the cold plunge … I know it is pricey but I am looking at the best options to add to my routine … thank you for all the content
Will the 1/4hp chiller work fine for me? Trying to keep this as budget friendly as possible,I’m located in sw Florida so it gets hot but plan on setting it up in my garage
Does the chiller need to run constantly 24/7? I understand you can turn it off for the couple minutes you're in the tub. How long would something like a 1/4 hp chiller take to cool the water 20ish degrees? Thanks as always for the content!
I keep it on 24/7 but it only runs when it needs to chill the water back to set temp. Otherwise its just a pass through. That is a good test, from my experience in FL it doesnt take longer than about 5-6 hours. Basically I would fill up and turn on at night, by morning its cold. In 20 degrees it should take way less time, id leave the lid off in that temp and let it really cool down fast.
David, great video. Quick question. If I wanted to add a filter would that go in the place of the strainer? Or is that something that I would need to add to the system in addition to the strainer? If that is the case, where in the system would it be placed? Thanks for any guidance.
David, thanks so much for all the info you provide. Your videos are crystal clear and your Amazon kits make things so easy! I'm going with the Active Aqua 1HP chiller and I have decided to install it in a waterproof vented deck box. I would like to get the deck box before the chiller arrives but I need to confirm what the vertical dimension is from base of the chiller to the highest point of the hose nipples on top so I can get a box that will accommodate. Can you tell me what that dimension is? I've tried finding it on the Active Aqua website and also through their customer service but I get different responses. I trust you to give me the correct answer. Thanks!
I’m not sure if active aqua has changed their thread sizes since you posted this video, but the active aqua 800gph pump included in your 1/2HP kit does not have 3/4 inch threads inside of the pump, the are 5/8 inch threads. Just a heads up, I still appreciate your videos, but you may want to update that kit because I suspect the 1000GPH pump actually does have 3/4 inch threads but the 800GPH does not.
Hi David. I am terrible at DIY projects. I bought the ice barrel 300 tub and a Nuvio recovery chiller (1/3 HP). I am struggling to figure out how to connect it. Can you help?
Awesome! Not hard at all, you really wont need it permanantly, you could also get a unit to use only when needed. I have a link to the one i use in this video (my cleaning kits) if you want to check it out
Great video. Makes it really simple. I've seen in other videos that you thought 1/4hp chiller would be enough for the IB300. Anymore thoughts on that? I got my barrel and the chiller is next!
So I just purchased an Ice Barrel 300 using your code. Very nice. Question, I live in a four seasons climate and shortly it will be getting cold enough where I will not be having to chill my water much. I would like to filter and keep the water fresh to limit how often I'd have to drain it, especially as it gets colder out. Would it be possible to go from strainer to pump to whole house filter and then back to the plunge, until it starts to get warm out again and I can add the chiller like in this setup? Thanks again
Absolutely! You’d be surprised at how well the strainer does and you could just keep it all running and turn the chiller off in the winter. Did I understand your question correctly? I want to give you the best advice.
@@DavidMausJr I believe so. So same setup as you have here, just turn off the chiller? Water will flow through it but not be chilled by it since there is no need? Am I following? :)
Hey David, been waiting for Ice Barrel's chiller, got rhe email today, looks really nice, but yikes! The price. I'm now thinking about going with your set up here, but it's in my garage so I'm not sure about draining it. Can you explain the best way i would do so?
Important: All ports on the Ice Barrel 300 are 3/4 NPT (not GHT). Several of Dave’s kits include GHT threaded adapters that do not fit the Ice Barrel 300. Using those GHT adapters will result in damaging the threads on the Ice Barrel.
Thanks for the heads up. For reference, i agree with you however the pieces i have in the kits are exactly (after trial and error) what I am using and there are zero issues. I have updated all the kits for the 300 and they have both options. If you want to go with NPT to NPT exclusive, they are the brass options in the kits. Any questions, message me on IG: @dmausjr
Hi David, pinged you earlier on IG as well but speaking of 3/4 NPT to NPT, does Amazon have this in non-brass options? Thinking of removing the brass I've inserted now due to some leaking issues. Also, for the pump, I see a leak at the base of the barbed hose connector. This is the one that came with the pump. Should I purchase a different barbed hose connector for the pump that will fit my 3/4 inch hose? if so what is the thread connector size to the 1000gph pump @@DavidMausJr
Hi my friend your videos are the reason i purchased my ice barrel. I’m looking at the ice barrel chiller and thinking of preordering it. What are you thoughts i know you use the aqua chiller. I just wanted to make sure i made a smart choice before spending 2500$
Glad to help! I havent got a chance to play with the new chiller yet but i hear its going to be epic. I have never had an issue with my DIY setup, check it out here dmjr.co/500DIYkit
@@DavidMausJr I did i love your videos, just curious if you would recommend there’s vs the dyi setup. Dyi looks like it saves you close to 1000$ lol. I know they have no info on it yet. Just thinking dyi or splurge on there’s? Always hard questions.
The adapter you have in your 1" kit is 3/4 GHT to 1" NPT.... is the ice barrel 300 threaded with 3/4" Garden Hose Thread or is it 3/4" National Pipe Thread? If it is 3/4" NPT you have the wrong adapter on your amazon page.
I accidentally damaged the fittings supplied by Ice Barrell. I waiting for a reply from ice Barrell, but am willing to purchase on Amazon if you know of any solutions? I’m using a 1” tubing. Thx
I really like the ice barrel 300, but I would like it even more if it had 1 in threaded holes instead of the 3/4 in. It seems like you will be putting a strain on the chiller if you opt for a chiller that has 1 in intake outlet.
@@DavidMausJr hey thanks for replying. Even with the adapter, you're still shrinking the hole to 3/4-in. Still hoping they upgrade to a one inch hole and let people buy adapters to get it down to 3/4-in if they want, haha Thanks for the great work by the way on your channel. Excellent coverage of products from all angles.
![ค้าง (STILL) - GEMINI [ OFFICIAL MV ]](http://i.ytimg.com/vi/Ftxx3hk5vkU/mqdefault.jpg)
Thank you so much for the love and support on my channel! If there is anything you wish to see next, let me know here in the comments. If not, just comment your favorite emoji that comes to mind when you watch my vids. :)
Bought this, set it up and am enjoying it ..... one question or troubleshooting help item. My pump seems to be working well (plenty of flow into chiller when I disconnect the "in" tube to check).... but I am regularly having trouble getting the water from the chiller back into the ice barrel. I have "purged the line of air", sort of checked all, etc.....is there a setting on the chiller that could be causing this that I am missing? Any help or suggestions are appreciated. Keep up the good work promoting what I think is a good healthy habit! Thanks!
@davidMausJr or anyone else has the answer to this, let me know. Thanks!
Because of you and your videos, I bought an ice barrel 300 (and used the code MAUS)! Thank you for all your hard work and tutorials 🙌
You just made my whole day. That is why I do this. Thank you my friend.
Same but they never applied your affiliate code.
That makes me sad, i wonder why?@@AreshSaqib
@@DavidMausJr well I forgot to add your code. Then they never answered me to add the code in. It’s been several weeks. Zero reply to emails. Don’t think i will be doing business with them again. Never heard of a company taking weeks to answer support emails.
The most helpful video I have found so far,
Straightforward,to the point, easy to follow instructions, good product recommendation
Thank you
Awesome, thank you!
Do you get in the tub when the chiller and pumps are running ? Or do you unplug them?
Run at all times
Great Video! Have you worked on the 140 Gallon XL inflatable tubs?
Hi David - Excuse me if this was already addressed; why is there a need to have a separate water pump, aside from the chiller? I've seen other chillers without external water pumps. Secondly, how do you sink up the water pump and the chiller from a power perspective or are the pump and chiller always plugged in and turned on?
Got it
Thanks for responding
It was really tight and I didn’t want to break it.
Totally! Any time!
I tighten the screw that connects the barrel to the filter too tight and now the tube is cracked inside the barrel and leaking. Anyone know where I can order a new part?
Could u do this minus the chiller for the filter and circulation?
Loved the video and the clear, concise instructions for adding the various components. Do you have a suggestion for a cheaper alternative to the IB300? The Ice Barrel is out of my budget range at the moment, but I would like to use your 1/4 HP cold plunge kit with a more affordable tub/pod. Keep up the great work with the channel!
Thanks, ordered one last night hoping for that answer!
How do you clean out the barrel since your using the outlet for the chiller instead of the drain it comes with?
I purchased the pump you link to but the inside female end is 5/8, not 3/4. I am struggling to find a 5/8 to 3/4 coupling to connect the pump to the filter.
Oh no! That is my beef with teh amazon kits, they sometimes add options and you have to select the right one. Im sorry brother
@@DavidMausJr All good. I found a brass fitting that goes from 5/8 to 3/4 t Home Depot. Lowes and Ace didn't have one. Thanks
@@DavidMausJr Have everything setup properly, as in the video, though using 3/4 barb for slightly smaller hose (which I had in my old DIY and worked fine). Small leaks under intake from filter to pump, even though I have plumbers tape on each end. But my biggest concern is there is very little suction. The pump is trickling water through the chiller. My last DIY used a small pool pump and had plenty of power, but this pool pond pump feels weaker than it should be. At a loss, as I used to use a pond pump on my last one to drain water whenever I cleaned it out and it seemed to have more power/suction. At a loss here.
You had two answers on how to add drain outlet to keep water from going on floor when draining. You recommended faucet splitter or a pvc tee. Not sure which one would be better and no clear about how to use the tee. The faucet splitter would have the pump and strainer at an angle when connecting.
Possible to do a short video about this? Thanks
It’s very tricky and I have not found a great solution. I’m going to look for another option and post a follow up video
Thanks!
@@DavidMausJr
Just curious why you choose not to use a filter. I know the strainer sort of acts as a pre filter but every other set up I’ve seen has a filter as well. Thanks!
Same question here. No filter or ozone. Why? What do you do instead?
Glad you asked! The filters are just another monthly cost and they are going to get nasty. i use the Ice Barrel Stabilizer which works great plus i have a portable ozone machine i use in all my plunges about once a month. My water stays clean and clear without needing any extra stuff but people do go that route too and its great! I just like simple. The strainer keeps debris out of the pump and chiller and works just fine :)
@@DavidMausJr What ozone do you recommend?
@@DavidMausJrmuch appreciated my friend!
Thanks for the informative videos. I just ordered mine following your suggestions.
Awesome!!
Ok I have your list saved I wasn’t finding the black pvc type fittings. Thanks
You can use pvc or metal. Both should work. The original list kept going out of stock
Hey David, I got the 1/4 horsepower Amazon kit and 1 thing you would have to change is for the pump that was in the Amazon kit it’s afapate is 1/2 not a 3/4, everything else was right tho I just have to get a 1/2 to 3/4 adapter at lowes
Where can I find a plastic 3/4 x 3/4 Inch NPT Brass Hex Nipple Male Pipe Adapter? The brass seems to crack and ruin the plastic threads.
Search on Amazon. They are always going out of stock. Hard to keep on the DIY kit list.
Love your videos! I know in your other videos you mentioned that there's a possibility that the inline pumps can burn out, I was wondering if you experienced that with an Active Aqua water pump or was it a different brand? If so, how long did it take for it to burn out?
Switched to Danner pumps, they are little beasts. Yes they could all theoretically burn out if they were on for a while with no water in the line. That is the main concern
ActiveAqua says to set a deadband setting instead of turning it on and off. Do you do that? If so do you keep the pump running all the time?
Would you recommend using an ozone generator with air stone with the ice barrel?
Yes
The male thread to male thread, where it connects to the pump keeps cracking and leaking water. Think it’s due to the weight of the pump not leaning on anything. This has been my second pump that’s cracked…
Good morning David, awesome videos! Can you please help me understand "fill the tip" at 12:02? How do I accomplish this step? Stay blessed brother!
You got it! Super simple, all you need to do is fill the barrel up with water and look for water to enter into the strainer, if you dont see water, open up the hose to let teh air out. The goal is to make sure water is in the pump.
Just to clarify, the filling up and looking for water to enter the strainer occurs before turning on pump/chiller? TY for a quick reply! @@DavidMausJr
You said a “strainer.” Is that the filter?
How long does the water stay clean?
How often do I need to dump and refill with new water?
Chlorine?
I want to do this but I don’t know how long the water is going to stay clean and what to treat my water with.
The strainer filtered almost exactly what a 20 micron filter will, it doesn’t need replacing. Water will stay as clean as you keep it clean. People use chemicals but I tend to just use hydrogen peroxide and occasionally ozone. Water stays clean for
Months.
I’m using Active Aqua submersible pump AAPW800 and I’m doing the 1/2 go chiller with 3/4 connections. But when I open the pump to attach the strainer the pump inner thread is slightly smaller than 3/4”. Any thoughts? Thanks!
That was my concern with offering options. You will need to get a converter, the tip might be a 1/2" so you might need to order a 1/2" to 3/4' inch adapter or run it to home depot. If you can, send me a pic on IG @dmausjr
Did you ever figure out a solution to this? I’m having the same problem. The 3/4 is slightly too big. And the included piece that does screw in perfectly has a barb that is too big for my 3/4” hose. Super frustrating.
Same issue. Inner thread looks to be 5/8”
thanks so much for all the help! I ended up buying the 800 gpm pumps and the front cover had a 5/8 thread rather than a 3/4. Did this change since the video was made or should I have gotten the 1000 gpm pump?
So sorry that happened! Amazon changes it and adds options. The 1000 is what you need.
Awesome, thanks David 🙏
how do you remove the spigot from the ice barrel 300 prior to adding the in line filter
Simply unscrew it.
Hi David. Thanks for this video as this is very thorough indeed. However, I've run into an issue where my 3/4" male adapter is not able to connect to the pump. I've tried numerous times and 2 unique 3/4" male adapters but to no avail. These same adapters have no issues connecting to the strainer on either end so I'm a bit lost here. I'm curious but I just checked my pump and it is the Style: 800 GPH model. Is it mandated I purchase the 1000 GPH model instead?
Ok just following up here but the 800gph pump has a 5/8" thread after noticing another hose fitting I was able to connect. I've submitted a return to Amazon and hoping the 1000gph pump model will have 3/4" female threading to fit the 3/4" male adapter.
Did you also send me a message on IG just want to make sure I give you the help you need. Sounds like you got it figured out. 🤙🏽
Yes, thanks again @@DavidMausJr all squared away so now just wait for the barrel arrival tomorrow and the pump on Wednesday. I should be good to start cold plunging this week, thanks to your reviews
Does the strainer leak have you figured out how to set it up without leaks?
Where can I find a plastic homogeneous 3/4 x 3/4 Inch NPT Brass Hex Nipple Male Pipe Adapter? The brass
Search Amazon they are always in and out of stock.
Thanks for the video! Saved me some headaches setting up my system
Glad to help!
Finally got it set up. It works good. But it is leaking (dripping) from two of the connections. Does it do that on yours?
It can be a little finicky and when I change it up I can get slight drips, just have to tighten or losen a small amount usually.
@@DavidMausJr thanks. And last question then I swear I’ll leave you alone. Although I live in Texas, it’s supposed to be down in single digits and my chiller is out side. You think that will be an issue or should I dc it and bring the chiller inside
It works!!! Thank you. Only problem I see. Does anyone have a filter that drips water ? I’ve tried tightening it, but a little drip every 3 seconds
Nvm. I plunged the hole. Opened up the filter. Readjusted it and tightened it back up. Works perfect
Perfect!
Let's say we have a week or 2 where the ambient temps outside are in the 40's. Can you use pump only to keep the water moving through the 'off chiller' Orr if we're plumbed through the chiller, it needs to be running? If it needs to be running, you would just shortcut the system with pump only flow during colder temps no through chiller, yeah?
Totally you can run the pump with the chiller off, its basically just tubes running through the chilling unit and that is what you turn on.
@@DavidMausJr perfect. Thanks!
Active Aqua says they are for indoor use only, do you have any recommendations on a covering for it outside?
I think me and 10,000+ other people who have had their active aqua chillers outside in the elements since day one would say you are absolutely fine with them outside as they are. Obviously do so at your own risk... but Plunge used active aqua for years before making their own new chiller and they are all doing great outside. Active Aqua needs to make some changes to their recommendations
Can that chiller and the attachments survive outside in freezing elements?
As long as the water doesn’t stop flowing it should be fine, but if that’s a risk, bring it in and use it as an ice bath.
@@DavidMausJr much appreciated for the response
Hi I just received my ice barrel three hundred, I bought a intex filter via Amazon. I’m a little confused with setting it up. I can be reached and I’m in south Florida. 😊
Send me a DM on Instagram @dmausjr I can help you through it
Thank you for putting this together, great setup. I have been running for the last two months without issues but recently the filter just stops pumping water after a while which I assume is due to air build up. I primed it by filling the tubes with water and that seems to work for about a day and then the same happens again. Am I doing something wrong and is there a good solution for this? Thank you
Good chance the screen filter is clogged up, take that off and spray it out, that should work
I appreciate you creating this video as it clarifies my questions before investing in a "Cold Plunge". Thank you for creating such informative videos. Your content is truly helpful, and I hope you will continue to produce more of it in the future.
Very welcome!
David, I got the 800 pump and I'm using 3/4" tubing and everything. I got 2x 3/4" x 3/4" fittings to link the strainer and the pump together, but my 3/4" fitting won't fit in to the 800. It looks like I need 3/4" to 5/8"
Oh no! Yea the 800 might be a smaller hole. I use the 1100 and it comes with the right pieces. So sorry my friend. But you should be able to get that cheap on Amazon
The silicon tubing in the amazon kit is 3/4 inch inner diameter and you say the tube should be 1 inch, right? I dont understand
The sizing is different for each chiller. It depends on the chiller u pick
1/4 says 800gph but that does not have 3/4 holes. Any ideas if the the 1,000gph pump will be to much
so you found that you didn't need any Teflon tape or o-rings on any of the fittings that you screw in that are from leaking or slightly dripping? also all fittings that were PVC like this for just hand tighten you didn't need tools to stop them from leaking etc.. I imagine over-tightening is worth cuz you could crack the plastic? thanks so much for your help and and videos
Thanks for the support and question. I didn’t use any tape, but it could help if needed. I also hand tighten almost everything, but I used a wrench a few times but not to over tighten, just to make it easier.
Think a 1/2 HP paired with the 300 can hang for the stupid hot summers in Phoenix? Or is it best to go with more horses? It’ll be under the patio, but outside will still be a brisk 110°.
With the 300 it should be good to go but the 1hp is a complete beast and can handle any heat I’ve thrown at it
@@DavidMausJr thank you sir! Appreciate your work
Always! @@Eric-1776
@davidmausjr. Where did you purchase the active aqua chiller?
amazon. i have links in vid description
Thanks for the video. I ordered my Ice Barrel 300 back in August but haven't received mine yet. In fact, I've tried contacting Ice Barrel multiple times through multiple channels to get an ETA and they won't answer me.
Oh man i am sorry about that! I know when i was at the HQ they were slammed with emails about shipping and they are a small team (currently building and growing). They were like "man i want to respond to each and every email about the shipping, but that would take hours and in that time i could also just process the shipping... dont want to make people mad but im going to just ship them their barrels." not word for word but i agreed. Its coming soon and i hope it comes sooner my friend.
So that pump is a submersible pump, but you can use it out of the water, and it won't burn up? Also, does the 3/4 adapter come with the pump once you remove that filter cover on the pump? You went over that part kind of fast. Thanks brother :)
Can you use a pump with less power? I have a 400gph and I’m trying to decide if I need to buy the one in the video
If there is any advice I can give to anyone wanting to do this DIY, please dont go with any less than the 1000 gph pump. The fittings are all different on the smaller ones.
Can you run 1,000 on the 1/4 it recommends 500 to 800?
My 1HP is set up with 3/4 inch (connections, hose, etc) ... Any advantages to changing to 1 inch or disadvantages/issues staying with 3/4?
You should be good to go with it! It just helps with water flow rate but you are fine with 3/4"
@DavidMausJr do you recommend using plumbers tape on the thread of the adapters and whatnot?
You can but its not entirely needed.
Anyone know what pump and strainer that is? Can’t find it anywhere
It’s in the kit in the video description
My 300 came with a faucet and I'm having a hard time removing it so i can use the 3/4 adapter to connect to the rest of the setup. I'm hoping the faucet can be removed somehow
It should just unscrew. It might be on tight. Or yes you can use everything and just connect to that hose bib it will just angle down and might not work perfect. Play with it and let me know. Feel free to message me on IG @dmausjr and i will help you through it
I found your Amazon DIY list for 3/4” setup!! That’s awesome. You mentioned an ozonator in the video. I saw the green water killer on the Amazon page, but not sure that’s it. Hoping to locate something next to the pump and chiller setup which will be about 15’ from the Barrel. Any recommendations for some type of inline sanitizer? Thanks, David!
Could i use the all the parts with your 1/2hp kit with 1/4 hp chiller? I would rather have plastic then stainless fittings
For sure just adjust the size if needed
your submersable pump, what is the GPH.. if the rate of GPH is too high for your chiller, would it max out or overheat/overwhelm your chiller?
Could you leave that set up out in a cold garage or out building or would it freeze and break the chiller when it’s below 30 outside?
It should be fine as long as water is always moving through the chiller
I put in a UV green killing machine light in my plunge use hydrogen peroxide and water barrel stabilizer, do I need like a marine land water filter in my ice barrel too? I have this exact setup with strainer and all
hi david , is i have the 1/2 hp chiller , will the 3/4 tubing will fit in the top part of the pump trough the chiller ? i think i heard you saying that the top tub attached to the pump is 1 inch ?
Don’t have a link to the adapters?
They are in all the DIY kits in the description of the video
How often do you change water
About once a month or so
Hey David! Thanks for sharing your processes with us. I just followed the exact steps to install an active aqua chiller to my IB 300. Does the strainer get filled to the top when its facing up like that? Mine is only filling up just a little bit so I'm not sure if it's actually filtering the water. Thanks!
Awesome! It should still filter the water just fine. How’s your water flow?
Love your videos! So I put together the kit and cracked the lower threaded plug. How do you order parts from IceBarrel? I put in a support ticket and tried to use their chat feature on the site but no luck.
Oh no! That a thick plug how did you crack that. Send me a pic of instagram @dmausjr
Is it safe to have it running if you have a gfci plug?
I do, but others say to turn it off. Depends on your safety preferences and experiences
Dumb question, but how do you empty the water once the chiller is attached? Is there a seperate port? Asking for cleaning purposes.
add a quick connect adapter to the release valve part and just quickly disconnect the chiller /pump assembly and empty water to refill the designed way
Great suggestion. Where I have mine I can just open up the strainer canister and it will all drain out
What do you think about the cold plunge … I know it is pricey but I am looking at the best options to add to my routine … thank you for all the content
It's great! I have a deep dive on it too! th-cam.com/video/NsofB5vWSL4/w-d-xo.htmlsi=DKwJtD419Vam0IhG
Will the 1/4hp chiller work fine for me? Trying to keep this as budget friendly as possible,I’m located in sw Florida so it gets hot but plan on setting it up in my garage
I really think so!
Does the chiller need to run constantly 24/7? I understand you can turn it off for the couple minutes you're in the tub. How long would something like a 1/4 hp chiller take to cool the water 20ish degrees? Thanks as always for the content!
I keep it on 24/7 but it only runs when it needs to chill the water back to set temp. Otherwise its just a pass through. That is a good test, from my experience in FL it doesnt take longer than about 5-6 hours. Basically I would fill up and turn on at night, by morning its cold. In 20 degrees it should take way less time, id leave the lid off in that temp and let it really cool down fast.
Can you do a video on maintenance of The Plunge during the winter months, specifically in NJ
For sure!
Super helpful tutorial. I live in a Europe and wondering if you can recommend the pump/ filter and chiller options available in the EU?
Look up the equivalent to the Active Aqua. I don’t know the name there but the same manufacturer makes most around the world.
Is there a way to add the ports to the 400 to make this work
i am super confident there is a way to do that, i havent yet but thinking about doing it next
David, great video. Quick question. If I wanted to add a filter would that go in the place of the strainer? Or is that something that I would need to add to the system in addition to the strainer? If that is the case, where in the system would it be placed? Thanks for any guidance.
David, thanks so much for all the info you provide. Your videos are crystal clear and your Amazon kits make things so easy! I'm going with the Active Aqua 1HP chiller and I have decided to install it in a waterproof vented deck box. I would like to get the deck box before the chiller arrives but I need to confirm what the vertical dimension is from base of the chiller to the highest point of the hose nipples on top so I can get a box that will accommodate. Can you tell me what that dimension is? I've tried finding it on the Active Aqua website and also through their customer service but I get different responses. I trust you to give me the correct answer. Thanks!
Awesome and thanks for the love! I just measured it and you’ll need 24-26” from floor to accommodate the tips and hose. Send me pics on insta @dmausjr
@@DavidMausJr Perfect! Thank you for the response.
Love the video, where was the walkinginrain shut off valve mentioned in the video?
Does it matter if I were to use the Danner 1200 pump with a 1/4 hp chiller? I’d like to have a little more flow than the 950.
I’m not sure if active aqua has changed their thread sizes since you posted this video, but the active aqua 800gph pump included in your 1/2HP kit does not have 3/4 inch threads inside of the pump, the are 5/8 inch threads. Just a heads up, I still appreciate your videos, but you may want to update that kit because I suspect the 1000GPH pump actually does have 3/4 inch threads but the 800GPH does not.
yes it sucks ! difficult to find 5/8 to 3/4 ? I have been looking online and cannot find.
Came back to this video for this exact reason, anyone find a 5/8 to 3/4?
@@chesallen6806I had to solve for this yesterday. They have 5/8” to 3/4” male-male adapters at Lowe’s
Anyone ever figure this out? Does the 1000GHP have 3/4” threads or is there a 3/4 to 5/8” adapter?
Yeah I just ended up buying the 1000GPH pump and it does have 3/4inch threads.
With your Ice barrel 300 setup. How low can you get the temp during Florida’s summer ?
39 on the money, and you can always add ice to that to make it lower. The insulation does an incredible job.
@@DavidMausJr was this using the 1hp or 1/2 hp chiller? I believe you said you keep it outdoors?
Hi David. I am terrible at DIY projects. I bought the ice barrel 300 tub and a Nuvio recovery chiller (1/3 HP). I am struggling to figure out how to connect it. Can you help?
How often do you change your strainer? And does it keep your water clean? I seen others using a bigger filter and what not
I change the water and clean the strainer once a month. It does a great job. A lot of people went overkill but that is the beauty of a DIY
Can I put in garage without or will it sweat a lot ?
You can! The 300 itself wont sweat much at all, but the tubing from the chiller setup will, its not that crazy, but it will.
How hard would it cost to add ozone? I just ordered the Ice Barrel 300 - thank you for the code. I’m going to order the Penguin 3/4 horse chiller.
Awesome! Not hard at all, you really wont need it permanantly, you could also get a unit to use only when needed. I have a link to the one i use in this video (my cleaning kits) if you want to check it out
Great video. Makes it really simple. I've seen in other videos that you thought 1/4hp chiller would be enough for the IB300. Anymore thoughts on that? I got my barrel and the chiller is next!
Yes 1/4 is plenty with the insulation. 🤙🏽
So I just purchased an Ice Barrel 300 using your code. Very nice. Question, I live in a four seasons climate and shortly it will be getting cold enough where I will not be having to chill my water much. I would like to filter and keep the water fresh to limit how often I'd have to drain it, especially as it gets colder out. Would it be possible to go from strainer to pump to whole house filter and then back to the plunge, until it starts to get warm out again and I can add the chiller like in this setup? Thanks again
Absolutely! You’d be surprised at how well the strainer does and you could just keep it all running and turn the chiller off in the winter. Did I understand your question correctly? I want to give you the best advice.
@@DavidMausJr I believe so. So same setup as you have here, just turn off the chiller? Water will flow through it but not be chilled by it since there is no need? Am I following? :)
yep that should work perfectly for you!@@erikknapp5775
Hey David, been waiting for Ice Barrel's chiller, got rhe email today, looks really nice, but yikes! The price. I'm now thinking about going with your set up here, but it's in my garage so I'm not sure about draining it. Can you explain the best way i would do so?
Totally! I’m going to do a new video explaining it but there’s a way for sure.
Basically get everything in this kit. amzn.to/3RLFZx9 and it will make sense
looking forward to the video! I see the on off valve is something new in your Amazon list - interesting!
@@DavidMausJr
also, do you think the 25hp chiller is plenty inside a finished garage? I probably won't ever go below 40 degrees@@DavidMausJr
Hey David. Amazon has some 1/2 HP chillers in stock if you want to let people know.
Whoop whoop!!
Important: All ports on the Ice Barrel 300 are 3/4 NPT (not GHT). Several of Dave’s kits include GHT threaded adapters that do not fit the Ice Barrel 300. Using those GHT adapters will result in damaging the threads on the Ice Barrel.
Thanks for the heads up. For reference, i agree with you however the pieces i have in the kits are exactly (after trial and error) what I am using and there are zero issues. I have updated all the kits for the 300 and they have both options. If you want to go with NPT to NPT exclusive, they are the brass options in the kits.
Any questions, message me on IG: @dmausjr
Thank you @DavidMausJr Very appreciate of your helpful reviews.
Hi David, pinged you earlier on IG as well but speaking of 3/4 NPT to NPT, does Amazon have this in non-brass options? Thinking of removing the brass I've inserted now due to some leaking issues. Also, for the pump, I see a leak at the base of the barbed hose connector. This is the one that came with the pump. Should I purchase a different barbed hose connector for the pump that will fit my 3/4 inch hose? if so what is the thread connector size to the 1000gph pump @@DavidMausJr
Hi my friend your videos are the reason i purchased my ice barrel. I’m looking at the ice barrel chiller and thinking of preordering it. What are you thoughts i know you use the aqua chiller. I just wanted to make sure i made a smart choice before spending 2500$
Glad to help! I havent got a chance to play with the new chiller yet but i hear its going to be epic. I have never had an issue with my DIY setup, check it out here dmjr.co/500DIYkit
@@DavidMausJr I did i love your videos, just curious if you would recommend there’s vs the dyi setup. Dyi looks like it saves you close to 1000$ lol. I know they have no info on it yet. Just thinking dyi or splurge on there’s? Always hard questions.
The adapter you have in your 1" kit is 3/4 GHT to 1" NPT.... is the ice barrel
300 threaded with 3/4" Garden Hose Thread or is it 3/4" National Pipe Thread? If it is 3/4" NPT you have the wrong adapter on your amazon page.
SHOULD BE NPT. Amazon links keep changing it up, im sorry. Fixing now.
Just used your code brotha, looking forward to getting the 300
You rock! Enjoy it!
Do you have a kit/build with 1/4hp? I think that might be all I need with the 300 inside.
For sure! That is a good option for the 300
Thanks for all the helpful content brother! If you choose not to run the chiller 24/7 do you turn both the chiller and pump off?
Thanks!! You sure can, but it will also shut itself off when the desired temp is reached (the chiller)
Hey David, what is the lowest temp you are able to get down to on the 1/2HP or 1HP chillers when used with the ice barrel 300?
39
you said it runs 24/7 out side ?
is it uncovered? rained on?
mine is coming in today , excited thanks for all the great info
That is correct! Awesome!! Enjoy!
Have you tried, or have an opinion on the Penguin chiller?
I have not but i have also not heard many good things about it
Thanks for the response.
I accidentally damaged the fittings supplied by Ice Barrell. I waiting for a reply from ice Barrell, but am willing to purchase on Amazon if you know of any solutions? I’m using a 1” tubing. Thx
Oh no! DM me on Instagram @dmausjr a pic of what you damaged
David, I'm wondering about having the pump run only when the chiller runs. Do you have any thoughts on that?
You can absolutely put this on a timer and save some electricity cost.
Great video on this install!
Thank you!
I really like the ice barrel 300, but I would like it even more if it had 1 in threaded holes instead of the 3/4 in. It seems like you will be putting a strain on the chiller if you opt for a chiller that has 1 in intake outlet.
Totally agree. 1” would be epic. That’s why I recommend getting the 3/4 - 1 inch adapter.
@@DavidMausJr hey thanks for replying. Even with the adapter, you're still shrinking the hole to 3/4-in. Still hoping they upgrade to a one inch hole and let people buy adapters to get it down to 3/4-in if they want, haha
Thanks for the great work by the way on your channel. Excellent coverage of products from all angles.
I have a question can I use a 1/2 horsepower chiller with 2 pumps to cool and filtrate 2 ice barrel 300’s at same time?
That is an EXCELLENT question and i honestly dont see why not. however i would probably go with the 1HP for the amount of water you want to push.
Has anyone used the 1,000 pump with the 1/4 chiller. I see the recommend 500 to 800 but would like to use the 3/4 adapters. Smaller pumps use 5/8