Shimano Hydraulic Road Disc Brake Alternative Bleed Method
ฝัง
- เผยแพร่เมื่อ 8 พ.ค. 2021
- Shimano Hydraulic Road Disc Brake Alternative Bleed Method If you find the videos helpful and would like to make a small donation to help support the channel you can do so here www.paypal.com/paypalme/freet...
Buy me a coffee
www.buymeacoffee.com/Freetocycle
Support the channel via the Patreon Page
/ freetocycle
Follow me on Instagram
freetocycle...
info@freetocycle.co.uk
Thanks for watching. - กีฬา
About to start my first bike build and your instructions are clear and concise. I've saved them in a 'how to build' file - thanks for sharing your knowledge.
Best video I have seen to bleed the rear caliper, congrats !
Awesome! I literally only just posted on your other video asking for this! Thanks!
Brilliant! Much easier than the full method. Thanks!
Awesome video, thanks. People say leave it to the professionals - well you’re a professional and your instructions are very clear 👍
Great instructions, well made.
These videos are amazing!
Giving it my first go tonight, great to have this guide to hand. Thanks.
Done. So simple. Built it up to be more in my head. Fantastic guidance, many thanks
A top tip if you have GRX with cross levers fitted too - don’t forget to give them a squeeze at the same time as the brake levers to get any air out of that area too. They’re easily overlooked as I found out the hard way 😏
Do you mean at the point of sucking it through with the syringe?
Could you do a video on Hope RX4 caliper alignment? I have the rear flatmount and it is a nightmare to get aligned.
will try on my Ultegra brakes, wish my luck and patience
Will this work on grx800 shifters and grx calipers I thought they only bleed one way?
Is it normal that a bleed (after two years or riding) has a lot of blackened mineral oil coming out from the system?
How do you flush it out completely and only have "clean" oil? And should I be concerned that maybe something is contaminated if the stuff got black? Brakes are still braking fine by the way, I'm just curious as to why it's very black.
Question - what is the problem if it feels hard to pull brakes (hydaulic brakes)?
Could you have done it the other way? Bleeding by pushing new brake fluid from the caliper using a syringe into the bleed cup...will that work too?
i think this method its easier to suck any bubbles out the calliper where they tend to get stuck.
great video very helpful like all your videos, I have astrange issue with my 105 rear that when I pull the lever the pressure fades after about ten seconds and the lever creeps fully to the bar . if i pull it again it holds pressure again but fades. When I bleed and i ve tried it loads it seems to always have air however much i bleed it. I checked the lever changed the little bladder and inspected for leaks but cant see anything leaking to cause pressure loss. It all started after the lever was forced back after driving into a high barrier with the bike on my roof rack. Any ideas befofore I buy a new brake lever and caliper?
Don't buy new levers. I have the same issue and it simply isn't being bled thoroughly. Get all the air out and you'll be fine. A new lever will do the same.
I will try that with my GRXs because nothing worked at 100% so far even when following Shimano instructions step by step.
How did it go
hey Johny, did you manage it after a year? ;)
Hahaha I didn't die and my brakes are properly working now. The reservoir caps were loose on both of my brifters so a little bit of air was getting in. Took me a couple months to figure it out because I assumed Shimano's QC would have catch that!
What fluid did you use for GRX?
@@wanderingsofalanandcaz Shimano mineral oil. Don't use anything else!