HOW TO CONNECT INNOVV K2 TO CANSMART OR HEX EZCAN. + NEW R1250GSA FRONT MOUNTING POSITION.

แชร์
ฝัง
  • เผยแพร่เมื่อ 6 พ.ย. 2024

ความคิดเห็น • 83

  • @sedulousdabbler5468
    @sedulousdabbler5468 2 ปีที่แล้ว +1

    The only full explanation on the internet. Thank you.

  • @simoncarrier2411
    @simoncarrier2411 3 ปีที่แล้ว +2

    Without even seeing the video yet.... I’m preying that this will work for the K5 cause that’s where I’m at 🙏🏻🙏🏻🙏🏻🙏🏻🤷🏻‍♂️🤘🏻👌🏼

  • @markrichardson8329
    @markrichardson8329 3 ปีที่แล้ว +1

    The grill idea is brilliant. If my bike wasn’t going back to BMW, I’d get this done. I’ll have to wait for the new bike.

    • @davrac2008
      @davrac2008 3 ปีที่แล้ว +1

      HI Mark, why is the bike going back? curious i have a 2020 1250 GSA with some issues, and would like to know if im alone or in company?

    • @markrichardson8329
      @markrichardson8329 3 ปีที่แล้ว

      @@davrac2008 No issues with the bike. It has performed faultless. It’s just coming to the end of the finance agreement and I’m getting the new version.

  • @bigdog44b4u
    @bigdog44b4u 2 ปีที่แล้ว

    Wish there was a way for US customers to drop our bike for a few days. Thinking that might be a bit costly ha. Great channel and love the professionalism of the installs. Love discreet.

  • @robertyork4041
    @robertyork4041 3 ปีที่แล้ว +1

    Really nice, tidy installation. I am looking forward to the K5/K2 comparison and to see how you deal with the K5 mounting and access to it.

  • @pault4513
    @pault4513 ปีที่แล้ว

    Again I say I like the way you are doing things i am planning on buying my new 23 gs in the morning cross our fingers

  • @davrac2008
    @davrac2008 3 ปีที่แล้ว

    Hi Steve, love the AIRBNB idea, might look at that for future purchases and installs. make a weekend of it

  • @WoodNotts
    @WoodNotts 3 ปีที่แล้ว

    Hi Steve. Enjoyed the install vid and agree that the front and rear cameras are well suited to the central position. With your first hand knowledge do you think it feasible to mount the K5 on a steel bracket behind the grille such that it sits further forward than where your K2 lens was to get around seeing the sides of the beak. The grille could then be replaced with a 3D printed version that had a clearance hole with inbuilt bezel to sit around the lens but not touching and the whole grille front brought further forward to make it look standard. This could then be mounted either by screws or rubber push on type panel mountings making it easier to get access when needed. I’ve been toying with this for a while with my C5 (I needed audio as the memory isn’t that sharp these days😂😂) but I’m now looking to upgrade to the K5.
    Cheers and keep up the good work👍

  • @davidfieldhouse7722
    @davidfieldhouse7722 2 ปีที่แล้ว +2

    What size holesaw did you use, is it 25mm and 25mm electrical grommets

  • @pwestjr
    @pwestjr 3 ปีที่แล้ว

    Thanks for the shipping tip on the Skylift if sent to Colorado, U.S. I so want the Skylift but I guess it was not meant to be.
    I loved this video! You do brilliant work. Wish I could find someone here in Colorado that does as good of work, that you do.

  • @philc7135
    @philc7135 3 ปีที่แล้ว

    Brilliant video. Loving the position of that front camera. The fact you make the part for the customers is awesome 😎 it looks the DB.

  • @simonlloyd3936
    @simonlloyd3936 3 ปีที่แล้ว +1

    Bloody love it clean and tidy, best place for it, will be ordering my k2 soon, 👍

  • @magnusedwards5661
    @magnusedwards5661 3 ปีที่แล้ว +1

    Great install, think I’ll be moving my cameras as soon as i get a chance.

  • @brawlski
    @brawlski 3 ปีที่แล้ว

    Great use of the existing fixture. Belt n braces

  • @paullyddiard7429
    @paullyddiard7429 2 ปีที่แล้ว +1

    Hi, I am new to the BMW GS and I am wondering if that front camera grill fits the 2022 gs?

  • @최우기-h7j
    @최우기-h7j 3 ปีที่แล้ว

    I ordered so exciting ~ wait for the arrival to South Korea !!

  • @cvejarsaez
    @cvejarsaez 2 ปีที่แล้ว

    Hi Steve…just great !!!…. I love the profesional job. It looks coming out of factory. Look forward to the K5 mounting…. Cheers from Chile !!!

  • @julito_a
    @julito_a 3 ปีที่แล้ว

    Phenomenal job on the install and really appreciate your diligence in the tidiness of the install, use of braiding, crimping, etc. I can easily get away with those holes in the front/rear here int he US. Keep it up!

  • @sm3shg
    @sm3shg 3 ปีที่แล้ว +1

    Nice... take my money! Getting my R1250GSA tomorrow :)

  • @NJWMOTO
    @NJWMOTO ปีที่แล้ว +1

    Will this grill fit th e standard GS or is it just for the ADV ?

  • @simoncarrier2411
    @simoncarrier2411 3 ปีที่แล้ว +2

    Love the placements. I think the rear camera may need a peak from the number plate light above. The front camera is in a perfect position however I want the K5 and nothing to obscure the view so may have to go upside down under the beak. Loss of height but nothing to obscure the left and right. BUT HOW DO YOU PLACE IT THERE? 🤷🏻‍♂️ Till I figure it out I’m waiting to buy it. Excellent video has really helped me. 😳🙄👌🏼🤘🏻🙏🏻

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว +1

      Lots of though going into this......Good. I suggest a fork mount. www.abikething.com/product/denali-50mm-60mm-tube-mount-kit-for-mounting-auxiliary-lights-to-inverted-fork-tubes/

    • @simoncarrier2411
      @simoncarrier2411 3 ปีที่แล้ว

      @@ABIKETHING Thanks for replying... with all due respect I’m just not a fan of having the camera side mounted to the left or right. Also as the K5 camera has a side entrance to access the SD card you need access to the right hand side. The rear camera in the reflector centered BANG ON.... it’s just the front to figure out 😩🤷🏻‍♂️😳

  • @cantonakias
    @cantonakias 3 ปีที่แล้ว +1

    Nice install Steve! Why do you still recommend installing the DC converter directly to battery? Do we have any limitations or malfunctions if we go with the cansmart?
    I have this pigtail connector from you, and I would prefer to connect my K3 directly to cansmart!

  • @robinwilson7804
    @robinwilson7804 2 ปีที่แล้ว +1

    Hi Steve enjoyed the install vid, one daft question, when it comes time to change the bike is the reflector lens a replaceable item or does it come with the mud guard?

  • @mitchhoneysett7674
    @mitchhoneysett7674 3 ปีที่แล้ว

    Link to wiring guide not working.
    great video.
    Can wait to install on HD

  • @colinclugston4757
    @colinclugston4757 3 ปีที่แล้ว

    The grill is a fantastic idea.

  • @ogyedanjuma7413
    @ogyedanjuma7413 3 ปีที่แล้ว

    I think 'HEX' should incorporate a lean-sensitive function into its array of control-options in both the EZ-Can and CAN-Smart platforms.
    Since the lean-sensitive signal is already present in the CANBUS systems of these bikes, the 'cansmart' may piggyback off this opportunity to light-up/intensify corresponding pods on each side of the bike as the rider leans in (of course, provided that two circuits are set up as a light pair).
    I feel this can be done probably via a software update or a totally new firmware,
    This idea struck me because the cansmart and EZcan are currently able to utilize the ambient light sensors on these bikes to alter the pods' performance under different light conditions.
    Your thoughts Steve!?

  • @islanddreaming8591
    @islanddreaming8591 หลายเดือนก่อน

    @A Bike Thing, but what about Parking Mode on the Innovv? Q: Is parking mode / crash detection still functional when wired into the Hex/CanSmart when the motorcycle is turned off and unattended?

  • @andrewgordon9597
    @andrewgordon9597 3 ปีที่แล้ว

    Hi. Superb video covering lots of the interesting aspects of your work. Liked the direct connection to the Cansmart. Everything very positive. What is the crackling noise on the camera video? Finally, does the grill mount work on an F750GS?

  • @GeorgeNikolaidis
    @GeorgeNikolaidis 7 หลายเดือนก่อน

    Do you have a link please for the 3-pin canbus connector. I would like to use it for the chigee, which also have the yellow wire.

  • @williamginocchio1586
    @williamginocchio1586 3 ปีที่แล้ว +1

    Steve, I read in the K2 manual that wired this way may cause videos to not save on SD card? Have you seen this issue?
    Great install!

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว +1

      Yes, and I should have covered this.......This is why it's important to set the delay to 30 seconds on the programming.

  • @EmsillCazm
    @EmsillCazm 3 ปีที่แล้ว

    Hi Steve .... Could you not apply the same method of holding the camera on the rear as you did on the front grill by using a clamp ?

  • @FarhanKapadia
    @FarhanKapadia ปีที่แล้ว

    Thanks for your videos Steve. My 4 hex can circuits are taken up by 2x s4s, a B6 and a SoundBomb, if i want to add a k3, should i swap anything out or have it connected directly to the battery? Thanks!

  • @Gallagher2112
    @Gallagher2112 3 ปีที่แล้ว

    Bloody brilliant that is. Super clean look!

  • @krish4507
    @krish4507 3 ปีที่แล้ว +1

    It would be great if rear camera has thermal or night mode

  • @63chalkie
    @63chalkie 3 ปีที่แล้ว +1

    Nice install, one question is, does the Innov have a motion sensor that activates it if the bike is parked and the ignition is off. If so would this feature work with this set up?

    • @DaveBarnes1
      @DaveBarnes1 3 ปีที่แล้ว

      It might be a bit late, but it does indeed have a motion sensor. However, it needs the permanent 12v supply so that it can activate it, so I think you would have to connect it directly to the battery to make it work. But you could still connect the ezCan to the switched signal, and use that as the third wire on the Innovv supply, that way you have permanent power and a switched controllable signal.

  • @steveroberts8183
    @steveroberts8183 3 ปีที่แล้ว

    Hi Steve Awesome Idea!! Did you use a 24mm holesaw?

  • @stuartmcgifford3286
    @stuartmcgifford3286 3 ปีที่แล้ว +1

    Hi Steve
    Love the K2 and the idea of a grill mount. You fitted my K2 system back in November (just before you moved). How easy would it be to move the front camera to the grill system?

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว

      All depends on how much slack there is on the camera wire and whether it was coiled up ear front. Otherwise relatively easy

  • @toothl3ss91
    @toothl3ss91 3 ปีที่แล้ว

    I wish I still had my 2018 GSA Rallye (getting too old for dirt)! I am now buying 2021 R1250RT and want to install Innovv K2/3 on it. Have you done an install on an RT (especially the one with the ACC pod on the front)? That would be a great video...just saying.

  • @nickkennedy9604
    @nickkennedy9604 3 ปีที่แล้ว

    Does the motion detection still work if not connected to battery.
    I do prefer K2 rather than the K5

  • @iponsoinage2010
    @iponsoinage2010 2 ปีที่แล้ว

    Super mam tak samo zrobione .
    Super filmiki masz .
    W Polsce tylko by ciebie hejtowali.
    Super👍

  • @MikeGilroyAK
    @MikeGilroyAK 8 หลายเดือนก่อน

    Wonder if that front camera mount you sell will work with the chigee setup?

    • @ABIKETHING
      @ABIKETHING  8 หลายเดือนก่อน

      You just need to compare the diameters between the 2 cameras. I’m sure it’ll be very similar and will fit

  • @dhigh7426
    @dhigh7426 2 ปีที่แล้ว

    hello,
    So i had a question. I wired everything the way you did, but I am running into a problem. when ever I turn the bike on to accessory mode the innovv will not turn on, even if I turn the engine on. I have to manually push the silver button for it to come on and start recording. I made sure to wait plenty of time before hitting the silver button. Ive also played around with the setting on the cansmart app on my computer. I have the innovv k2 and denali lights (cansmart).

  • @richardthelionheart5072
    @richardthelionheart5072 3 ปีที่แล้ว

    What is the cost of putting cameras on I'm interested for my bike thanks

  • @tomassolnicky8967
    @tomassolnicky8967 2 ปีที่แล้ว

    Hi, Thank you for another best video .... Could you please explain difference between connecting K2 to cansmart or directly to battery ? Is there any advantage or disadvantage in each connections ? Thank you very much

    • @ABIKETHING
      @ABIKETHING  2 ปีที่แล้ว

      Doesn’t the video explain this?

  • @Trond_Karlsen
    @Trond_Karlsen 3 ปีที่แล้ว

    Sweet install of the K2, wondering if the K5 front mounts just as nice? BTW, just found your shop, channel and Facebook page so I have a ton of questions ;)

  • @susu198215
    @susu198215 ปีที่แล้ว

    Hi I have s1000xr 2017 , wanted to install K5 , but BMW dealer said it will give lot of error codes if I try to do it and try to tap on to Tail light cable for the K5 yellow cable .
    Is it true ? They said they will charge me 1500 $ in Sydney to do this job.
    I am confused. I don’t have hex easy can in my bike . So I have to tap on tail light cable . Is better to do it or 😢

  • @CO2W
    @CO2W 3 ปีที่แล้ว

    Excellent, nice clean install.

  • @stevescherer6704
    @stevescherer6704 3 ปีที่แล้ว

    Awesome installation and advice 😊

  • @marklloyd9472
    @marklloyd9472 3 ปีที่แล้ว

    Tidy tidy , both great positions just need the GSA in my garage ..

  • @Tijn1972
    @Tijn1972 3 ปีที่แล้ว

    All well and good, but this doesn't work all the time. My K2 power supply oveloads the Hex Excan/Denali smartcan on start up and ik flashes red. It once started and when on it operates at 0.6A, but on start up it might spike from 5A to 29A. So straight to the bettery still seems to be the best way although I would like to do it this way......

  • @2wheelzarebetter
    @2wheelzarebetter 3 ปีที่แล้ว +1

    I dont think the rear reflector would be an issue, it doesnt state what size it has to be? On my srad they stuck a small round one to my numberplate for mot alot smaller than the gs one.

    • @robzz9002
      @robzz9002 3 ปีที่แล้ว +1

      Same on my bike. I’ve got the smallest legal plate I can have with one of those little round reflectors stuck in the corner. Didn’t have one when the bike went for it’s first mot and the tester said it would fail without it. Sold me a reflector for £1 and stuck it on then and there. Apparently that’s completely acceptable, so I don’t see how effectively having a reflector on either side of the camera would be any different.

  • @annagorska527
    @annagorska527 3 ปีที่แล้ว

    Hi Steve,
    Good video....
    What is the size of the grommet?
    That’s Rgds

    • @_ChrisOnTour_
      @_ChrisOnTour_ ปีที่แล้ว

      Hi Anna, maybe you know now which size do you need? I am also trying to figure it out.

  • @ogyedanjuma7413
    @ogyedanjuma7413 3 ปีที่แล้ว

    Beautiful install 👍🏾✌🏽

  • @markadempsey1
    @markadempsey1 3 ปีที่แล้ว

    I like it, nice clean install.

  • @theworldsbonkers
    @theworldsbonkers 7 หลายเดือนก่อน

    Hi Steve will this work with the Chigee front camera?

    • @ABIKETHING
      @ABIKETHING  7 หลายเดือนก่อน +1

      It should do. Waiting to get my hands on our first delivery next week

  • @krish4507
    @krish4507 3 ปีที่แล้ว

    Marvellous job

  • @joaofreches852
    @joaofreches852 3 ปีที่แล้ว +1

    Do you sell only the grill?
    The grill fits in the R1250gs?

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว +1

      Yes, I’ll Update the site later. It’ll fit a Gs but might look a little strange

    • @joaofreches852
      @joaofreches852 3 ปีที่แล้ว

      @@ABIKETHING The rubber rings you sell them to

  • @randomcrap763
    @randomcrap763 2 ปีที่แล้ว

    Wonder if we can mod that grille to fit on a GS :)

    • @ABIKETHING
      @ABIKETHING  2 ปีที่แล้ว

      It will on an older GS but not the 1250

  • @drfox100
    @drfox100 3 ปีที่แล้ว

    do these front grills fit a 2014 te edition

  • @bshortt4244
    @bshortt4244 3 ปีที่แล้ว

    looks really nice....

  • @ONAtubes
    @ONAtubes 3 ปีที่แล้ว +1

    can you shipping to Turkey ?

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว

      Sure, the website displays the prices in the shopping basket area.

  • @war3zuk
    @war3zuk 2 ปีที่แล้ว

    CB1000R 2021 Innov k5 install please lol

  • @kenny4k
    @kenny4k ปีที่แล้ว

    Stick one of those stupid 10p shape reflectors on the number plate if your worried. All sports bikes use them when they do a tail tidy 😂

  • @ogyedanjuma7413
    @ogyedanjuma7413 3 ปีที่แล้ว

    I could come work for you, if you don’t mind 😁

    • @ABIKETHING
      @ABIKETHING  3 ปีที่แล้ว

      I am looking for a new member of staff

    • @ogyedanjuma7413
      @ogyedanjuma7413 3 ปีที่แล้ว

      @@ABIKETHING I'm the man for the job.

  • @eddale5557
    @eddale5557 2 ปีที่แล้ว

    Why do any need all this cameraes is beyond me it dont make me who loook at the camera's on all the bloggers any good it is distraction, i have no interest in what is going on back of a mc when driving all i wanna se is what is in front and that's it! No damn 360 either it is annoying to watch so a normale Gopro on the helmet is more than enough!