How to Replace Window Regulator 01-03 Dodge Grand Caravan
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2024
- Buy Now!
New Power Window Motor & Regulator Assembly from 1AAuto.com 1aau.to/ia/1AWR...
1A Auto shows you how to repair, install, fix, change or replace a slow, stuck, cracked or damaged window regulator. This video is applicable to the 2001, 2002, 2003 Dodge Grand Caravan or Chrysler Town & Country
This process should be similar on the following vehicles:
2001 Dodge Grand Caravan
2002 Dodge Grand Caravan
2003 Dodge Grand Caravan
2004 Dodge Grand Caravan
2005 Dodge Grand Caravan
2006 Dodge Grand Caravan
2007 Dodge Grand Caravan
🔧 List of tools used:
• Phillips Head Screwdriver 1aau.to/oDF/1AX...
• 10mm Wrench 1aau.to/oiX/1AX...
• 10mm Socket 1aau.to/ozb/1AX...
• Needle nose pliers 1aau.to/oeY/1AX...
• Needle nose pliers 1aau.to/oeY/1AX...
• Wire Cutters
• T30 Driver 1aau.to/ogm/1AX...
• Ratchet 1aau.to/oGr/1AX...
Subscribe: / @1aauto
Check out our playlist:
Dodge Caravan 2001-2007 4th Gen: • Dodge Caravan 2001-200...
Dodge Auto Repair Videos: • Dodge Auto Repair Videos
For More Info visit us at 1aau.to/h/T5/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I cannot get over how much better this vid is than the one above it. This one includes all the critical & necessary steps the other one left out. Without them, you probably will not be able to do the repair.
Thank you SO much!!!
Rather than removing the glass from the door once it is released from the two clips, you can just pull the glass up to the top and use duck tape to hold window in place while reinstalling the track. This will save you 10+ minutes of struggle in an already PITA repair job.
Great tip! Thnx
One important tip: it is almost impossible to get out the 3 torx bolts that hold the motor to the door. you cannot grab behind there with pliers, you just cant get the torx bolts out. I managed to get one out then got a drill and drilled out the other two. After I did that , I read that you can just pry the old motor off the door - there is a rubber grommet that will put through the stamped hole in the door. doing this will save you tons of time in this repair. otherwise, the video made it very easy and logical to do. lastly, I bought a dorman motor and you had to cut the zip tie holding the window cable to the motor, they had it zip tied so you could not mount it on the door. give yourself 3 hours if your first time. Almost forgot - i did not take window entirely out of vehicle. after i got the clips off, i pulled window to the top and used tape to hold window in place. a lazy short cut that made it easier.
I do the same, I take the clip off, didn't need to move out the window because it is hard to put back.
Thank you for your tutoring. I checked the the tricky parts in your clip as I was replacing the passenger window regulator.
The right pin didn’t snap into the clip before you noted on tightening the rails after clipping the glass pins. That saved me every thing around the project. Thanks again 🤛
Toronto dealer wanted close to $600 . I bought a new unit on Amazon $75 and done it myself thanks to your video.
Thanks brother!!
Mike Boyd just replaced one on my Chrysler minivan. Cost me about $70.00 for the power window mechanism and did the installation myself.
Your video made changing mine out very easy! Videos like these are Very self empowering...
+Phoenix Rogers Thanks for watching. We are happy to here that we have helped you out. 1aauto.com
I used this video this morning to change out my busted window regulator in a 99 Dodge Grand Caravan took me less than 45 minutes it was perfect thanks for the help.
This is a model for auto repair instructional videos. Great video quality, stable image, good light, awesome miked audio, close-ups, stills, a complete, accurate set of instructions, and a list of tools. Well done!
+MJmcnult Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
Great video. Just did my regulator on my 2002 T&C. Step by step instructions were spot on. Very helpful to see the various challenges you had so when I experienced the same I knew to soldier on. Saved a ton doing it myself on my 250,000 mile beater.
Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +okiehokie pokie
i just put my new regulator,thanks to you man,God bless your job and thank you for this video.just save 150 bucks.awesome
+lonely boy Gv You're welcome! We're glad to hear that we were able to help you save some cash and get the job done yourself. That's exactly why we make these videos. For anyone else looking to do this job, we offer the parts on 1A Auto at the following link: www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA%20Comment&ATony
This guy makes it look so easy I just did mine yesterday took me about four hours it’s very hard to do there’s a lot of detailed stuff and very easy to mess but if you’ve done it before it’s easy
Thank you! Changed mine in around 20 minutes thanks to you and your great video.
The only issue I had was the rubber grommets being hard to grip with pliers but you can just slide a screw driver between the door panel and the motor, right by each screw, and lever it enough to create a little force so that the screws will undo without trying to hold the grommets with pliers. My new motor had 3 lock nuts on bolts which is way easier to get to with a ring spanner.
+Bindi E Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Hi
Just used this video to instal window regulator into 1999 Chrysler Grand Voyager. I must thank you for your help - took me just 50 minutes to change regulator. All working fine. - Good job with the video!!
Thank you for watching. Please let us know how the repair comes out! 1aauto.com 888-844-3393
This is a very good instructional video. I luckily found a new mopar replacement for cheap. (sorry guys ) The bolts holding the motor to the car didn't have torx, they were plastic push in posts. I promptly broke them removing the old motor! The new motor just snapped in place as it had the plastic posts too. Job went smoooooth. I probably would not have done this repair except for your guidance ! Thanks.
Intermittent loss of power to window motor. It started working after we took the door panel off, but we did not chase down the bad wire. It works today and that is good enough for me.
love your video, i just fixed my power window 2006 Dodge Grand Caravan it took me a lots of hour but i did it now my window is working and my ears wont hurt anymore. Thank you so much ur a great Teacher !!!!!
+Soledad Parent Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA+Comment&D_m8MM55BKk
Doing a door swap! Thank God for this video, you guys are awesome!!!
+Hank Holzman Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
gonna attempt this today with a 2001 town and country. already have dismantled the door fairly quickly to see the problem. so I'm pretty confident in doing this. thanks for the video.
Thank you for watching! Glad to be of help. Please let us know how the repair turns out. 1aauto.com 888-844-3393
repair was successful. had an issue with the rubber nuts on the old motor but got it off. dropped one of the screws to the regulator inside a space in the door and could not retrieve it, but found a similar screw in an old workout machine i have.
love the video because you didn't do a bunch of fast forwards except when boring tasks. letting video playout allows me to see more exact what to do and time it takes. thanks for effort
Thank You the Video! I watched it this morning and Changed the Power window Motor on My Daughters 2000 Grand Caravan with no Problems! Great Video Brother!
No problem. Glad to hear it helped you out. 1aauto.com?TH-cam&CTA%20Comment&ATony 866-403-3393
Just went and got chinese food in the Voyager. Wife was rolling up her window and BLAM. Welp, good thing it isn't too cold here... Great video, I have not seen a cable window regulator before (just scissor types) so pulling the door panel off was very confusing and had me worried I was gonna have to feed wire through those pullies and stuff. Seems like its a pretty simple bolt in.
Great video! Note that the electrical connectors on some models have locking clips that must be slid aside before the connector can be released. Also, order some replacement door panel retaining clips along with the new regulator. It’s common for old and brittle clips to break during disassembly.
+Michael Calkins thanks for checking us out, and we appreciate the extra tips!
Thanks Mike for the assist I was able to change my motor lift, BIG HELP...
+DJ KARIM FLORIDA Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA+Comment&D_m8MM55BKk
1A Auto Parts what i need do if my window glass tild a lit bit when i put down?
Thanks a lot
Once again, best repair videos on the internet. 1a auto videos got me back into trying serious auto repairs and maintenance. I think i have to buy my next used cars based on what 1a auto videos are available.
+Tom Covington Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
I've done about 200 of these over the years. Never once did I remove the glass out of the door. Just push the glass up and hold it in place by plastic clamps, tape, or a wooden wedge against the glass.
Well I hope you can help. My widow is stuck at the top, it's the plastic track follower. Any tricks to getting that out?
Clips are in the worst spot. thanks.
1A is the best step by step on TH-cam
Thank you for showing the trial and error of putting the window back in, I would have stopped there out of frustration. Very detailed and Informative.
+K C Thanks for the feedback!
just changed mine on a 2003 caravan went perfect thank you great video
Thank you for this video. It helped so much
Another great video from 1AAuto !!!!!
Who ever the engineer is SPECIAL
Thank you, so much, for sharing; great job and all was quite clear. Nevertheless, please tell me how I can determine the repair that is needed. My motor can be heard when trying to raise and lower the window, but the window doesn't move except when I pull it up, by hand.
I'm not an expert like video OP, but it sounds like there might be a broken cable in the regulator, or the window holders (4:53) have come disconnected from the window. In both cases the motor would run but the window would not move up or down properly.
When you pull it up, does it stay up, or does it easily slide (or fall) back down? On my 05 T&C (same design as this video), the nylon glides that run up and down the window rails broke, and the window just dropped down. You have to replace the entire assembly as shown here to fix it, you can't buy the glide separately. But at Rock Auto, it was only about $55 versus $194 (part only) at the dealer.
Thanks for the tips! I didn't have any trouble replacing the window regulator on the minivan! Peace.
+Scotts Contracting Thanks for checking us out. 1aauto.com
Tried and tried and tried, but couldn't get the old motor out. Nothing I did gave me enough grab on the rubber nuts to get things loose. Great video guide, and thanks for the information. Hopefully my next repair job will go better for me.
Great job! Thank you for making this easy, my install went smooth!
nice video now I can help my brother in law with his thanks
I'm a big fan
While your way worked with the window, that is not how it is done. I worked the line putting windows in on these vehicles and all FCA products are pretty much the same with regard to door windows. Stand behind the door with your arms reaching through the window frame and with the curved part of the glass pointing down insert it into the door halfway in, start turning the glass upright engaging the forward glass into the rubber glass guide and continue pulling it making sure the rear is now in the guide. Once it is in the track, from inside the door, lower the glass to the bottom, move the regulator to the halfway point and move the glass up with both hands and aline and snap in the pins, finished. You do not have to remove the glass for a regulator change. Pull the glass all the way up and using blue tape, tape it into place and change the regulator, then lower the glass, snap it in and finished. Great DIY video. Yea I know the doors when new at the assembly line are on a door swivel jig that lays the door flat, the process is still the same for a mounted door.
You helped me a lot and i thank you bro. 🎉
Your videos are great, thank you for doing them!
John Baumer You’re welcome! Thanks for watching 1aauto.com 866-403-3393
great video. having trouble getting the window to release from the regulator had the window to high in the track. Thanks.
I'm a mother of three on a fixed income, I tried to look around me to get my window fixed. They say between 350 and 450 to get it fixed. I'm just gonna do it myself. Thank you for this video
I just saved myself $120 in labor by watching your video. Thanks
Me too! Easy once you've seen it done.
thanks for the tutorial video, god bless you
+Noel Lopez Thank you for the positive feedback, we really appreciate it! If you have a minute, drop us a review on our Facebook page to let other people know about your experience with us. Here's a link: facebook.com/1AAuto/reviews/
P.S. Must be careful when buying replacement, because 2001 is different of 2002 and so on, I don't know which one is similar, I always go by the colour, the clip thing in 2001 is black and pink. One I didn't pay attention and had to take all apart again and take back to the store.
Great info thank you !
While watching this video, it looks very easy to do. However, I am in a wheelchair and I don’t have much help to do this kind of job. Am I able just to replace the motor and regulator without having to replace the window track and do all the extra steps?
Holy moly lookss like a pain in the rear . i think i ll be opening my door to fetch that drive thru burger from now on
Thank you!
This video was invaluable. Thanks.
+K. Chris Caldwell Thanks for checking us out!
Great Video... Just bought a 01' grand caravan that I got a great deal on. Problem is the window is out an door panel apart laying in backseat. I will use this video knowledge in installing a new regulator an getting it all put back together.
+TheTruckerRick Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA+Comment&D_m8MM55BKk
Cable wire slipped off somewhere,the end part& where does it connect too?it's from the passenger window motor regulator
I didn't see the step with the excessive cursing, sobbing, and drinking of alcohol... I thought those were essential rituals for Dodge owners.
On a 1998 Plymouth dodge caravan,,how does the wires that go around the spool inside the window motor go?we get them around& one side longer?we put the passenger side window motor in,then threaded wires around spool& put in middle where it goes,but one side of wire cable is longer
THANK YOU VERY MUCH FOR SHARING YOUR KNOWLEDGE
+RESIW WON Thanks for watching. We're glad you liked it. 1aauto.com?TH-cam&CTA%20Comment&ATony 866-403-3393
Thank you very much for your great video!
I've watched many of your videos and they have been very helpful. My 2001 Grand Caravan has one difference that is hangung me up. The regulator motor in the center of the door is being held up by three white plastic clips, similar to what the door panel is held on with instead of Torx screws. I can't find this in any book or video and have tried everything. Any ideas?
+Redheadryan Unfortunately this is the only video we have for this application, so we cannot further with those types of small hangups. www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA+Comment&D_m8MM55BKk
I did everything you showed in this video and after one year the problem is back, so I went to pick up parts to buy a used replacement, I tested there it worked, so I put in my husband's car it worked just on the first test, then I tried rolling down and it stopped halfway, I turned the car off removed the key count till 5 and turned on again, it worked on the first attempt to go up and down, but then stopped on halfway again, I am puzzled, I turned off and did the same procedure, counted till 5 and turned the car again, my husband wanted me to explain, I don't have idea what is wrong.
Thanks!
Great video
Very helpful
thanks
Thanks! Very helpful.
+Bradford Eaton Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Hello, I just watched this video today and replaced the window regulator on my 2001 dodge grand caravan. I was able to do everything with the window and it is now working better than ever. My new problem is that the rod that works the inner door handle came off the door and I now have no Idea where it goes and how to hook it back up. The outer door handle does work so I can open the door from the inside of the van if I reach out the window to do so. Please Please Please make a video on how to fix this problem?
Goodbye Haynes hello 1A. This was a ton of help. Good work and thank you for sharing your knowledge.
+jimbobgeorgejohn Thank you for watching. If any of our viewers need to make this repair, we carry the window regulator shown in this video on our website. Here's a link to them. We also offer free shipping on all orders in the lower 48 states. www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256
+1A Auto Parts this part couldn't wait but I just ordered some struts from you in appreciation. Thanks!
Anyone have a fix for the front window clip popping loose? Aside from removing it and modifying the angles of the front riser?
you are the bestmecanic
Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +josue 777
I live in Canada,t t try doing this on a cold day in Greely Ontario,Canada.❄️
I ran into a problem with removing the old window motor. The T30 torx screws were tightened too much into the rubber nuts, and so I can't remove them. I tried holding the nuts as firmly as I can with pliers, but the metal part of the nut just spins inside the rubber outer part. (3:15-4:00 in video)
I had the same problem. I just slid a flat screw driver between the door panel and the window motor, just near a screw, and levered it a little to create some force and then undid the screw. The lever force stops the rubber grommet from turning. Ditto for the next 2 screws. It made it easy.
please do a video on a 08 dodge avenger!!
I've got to repair my daughter's 2003 dodge caravan sport. So, do the motor and regulator need to be relpaced as a unit?
+patsguy369 We do carry just the power window motor for the 2003 Caravan. Here's a link to them on our website. Hope this helps you out www.1aauto.com/2003-dodge-caravan-power-window-motor/y-mo-c/2003-58-22?TH-cam&CTA%20Comment&ATony
Hello I have a Dodge Ram 1500 2002 and I want to have power windows power locks I have the electric doors with the switches and evening on them I just don't know how to wire them.. if you can help by guiding were do I get my power my ground.
+Julie Cruz We currently do not have that information available to us. You could try to post on a Dodge Ram forum to see if anyone has done this. Hope this helps out. 1aauto.com
No Crank No Spark... 1998 Dodge Caravan sport, 3.3 liter. I have power on the 10 amp starter fuse when the key is turned to start, I have constant power at the starter relay, my starter is Brand New and will crank when I connect power directly to the orange wire at the starter...My Starter will not crank when I try to jump the relay, my horn will not beep when I jump the horn relay...Also, I have no power at the Coil Pack when using a test light even when the key is in the start position. Any Thoughts where to go next?
Reply
+Knuckle Busters DIY We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Will a 2001 Chrysler town and country passenger side window motor would it fit a 2006 Chrysler town and country window motor?
+FREDDIE WILLIAMS It does not look like it would. There may be different designs. 1aauto.com
But good video
ok. i will
mine doesn't have t30 screws. it has some weird plastic thing that looks like a giant push clip. also the gear comes off of the motor with three screws.
+John Lord Yeah, there's little differences like that across model years, or maybe they were aftermarket parts someone used in a pinch. Glad you got the job done though, thanks for commenting! 1aauto.com?TH-cam&CTA%20Comment&ATony 866-403-3393
i think someone replaced the motor in my door at one time with one for a newer one. the 2008 model uses those pins. Do you guys sell those pins?
QUESTION CAN YOU JUST CHANGE THE MOTOR SO YOU DONT HAVE TO TAKE ALL THE EXTRA STUFF OFF OR WILL THIS NOT WORK I NOTICE THEY SELL JUST THE MOTOR BUT ITS USED
+Brian Hamm On this particular application the window motor is not serviceable. We carry the new window regulator with the motor shown in this video on our website. Here is a link to them. www.1aauto.com/2001-03-window-regulator-driver-side-front/i/1awrg00256?TH-cam&CTA+Comment&D_m8MM55BKk
close up on the rubber nuts
I was thinking... wouldn't it be easier to just tape the window in the up position, rather than remove it?
No, window and inner drip molding interfere with regulator track removal.
well, I did it with taping the window up from the top. worked like a charm.
You are correct, it's a lot easier to just tape the window up.
Hello, can you tell me the speaker size in the door? Thanks in advance.
At this time, we do not have the speaker size. Try contacting a local dealership or check online forums. +Haunter Mansion
I have a 1996 Chrysler Grand Voyager minivan. Do you have a link to replace the power windows on that vehicle?
+Frank Denardo We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application.
@@1AAuto thanks. I just got a job at AutoZone and I will be buying a new window track for the van. The video posted here will help. Mine has the power rear vent windows.
How much does it cost to buy the part and fix it at a garage?
How can I get my window in the down position since the motor is out? It is stuck almost all of the way up. (1988 GMC pickup)
+brenda horn You may have to reach inside of the door to see if one of the window regulator is caught on something which may be preventing the window from lowering. Hope this helps you out. Have a great day!
1A Auto Parts Thank you. I just taped up the window and was able to get everything off okay. Might be a bigger pain to do it this way but I tried everything to get it down (including "jumping" the switch and motor) and nothing worked at all. Lol
Didn't even show how to hook the glass to the tracks. That's the Cridical part ! Should have shown that on the work bench.
No one is struggling with the clips i see.... I'm so lost
Those harness tabs can be a real bear.
Am I the only one here who just wanna know how to install two regulators on one door for tint purposes only?
What?
✊🏾💯⭐
You sure know how to make it look so easy but it's not