Fixing a leaking Swing Arm Clicker Press (Most makes and models)

Tips for diagnosing and fixing leaks on most common makes and models of Swing Arm Clicker Presses. Similar brands of machine include:
Atom (Manufacturer's Supplies Co)
Hudson
CJRTec
Associated Pacific Machine Corp
Many Chinese brands that use a similar construction.
Swing Arm Clicker Presses put downward pressure on either single or multiple layers of material. This function together with the use of a steel rule die will cut predictable and highly repeatable patterns out of fabric, rubber, foam, nonwovens, leather, and many other non-metal substrates.
Products commonly cut on Swing Arm Clicker Presses include shoes, accessories, clothing, gaskets, paper-boxes, upholstery, abrasives, leather goods, insulation, vinyl stickers, paper goods, and much more.
Clicker Presses are popular because of the versatility offered by the “swing away” design of the arm and intuitive operational controls.
Email us at [e-mail] for more information and pricing.
To learn more about Hammerhead Cutting Systems and how we can help you with your manufacturing and equipment needs, check us out at:
www.americancl...

[@saleemkermashan9291]

Hi my press is smells like gas when I used it could this be a leaking or what you think please it is ATON CLICKER PRESS

[@cutelife7701]

If there is a leak from the front side of the motor, well, what can be done, how can it be solved, can the leak be stopped?

[@HammerheadMachinery]

At this point, the tank will need to be drained, the entire motor and flywheel will need to be removed and the pump will have to be detached to remove the plate that separates the two chamber and it will need to be resealed with a silicone sealant. The area will need to be cleaned well with acetone or mineral spirits to ensure the sealant properly bonds.

[@husainkhan8924]

Pluz help me how to pressur up down

[@HammerheadMachinery]

Pressure is normally controlled through a daylight adjuster or wheel (macro-adjustment) and a potentiometer or timer on the face of the head (micro adjustment). If you need any more information please call our service department. 801-613-7997. Thanks!

[@amrithMilW]

I was using one such machine.. cutting fabric. all of a sudden the head was not coming full down..later it was not moving down. what could be the issue??

[@mannyfernandez6860]

make sure there is power comimg in.

[@HammerheadMachinery]

Hi Amrithraj, there could be a few different reason this could happen.
If you are just hooking up the machine, the first most obvious step it to check the oil level and insure that the oil covers the intake filter properly.
If the machine was just hooked up, it is common for customers to have the polarity of the machine wrong (the motor will be spinning against the direction of the indicator arrow), and the frequently causes the head not to raise on first startup. You'll also see bubbles being blown in the oil if the polarity is wrong. To resolve, simply switch two legs of the incoming power supply.
It could be a bad pressure sensor (if you are in the pressure based cutting mode), which may cause inconsistent cutting results. This just needs to switched out for a good pressure sensor.
It could also be a bad potentiometer or timer dial, causing inconsistent results for resistance. Again, this would just need to be switched for a new potentiometer or dial.
There is also a cable attached via a pulley in the head to the solenoid block to close the solenoid valve at the set rising height. If this comes loose, sometime this causes issues with rising height, then also cutting depth because it is not cutting from the same, consistent origin point (If it is in a time-based cutting mode).
The last common problem is a bad PCB board where burned capacitors, fuses, or circuits are often the cause. For this- same thing applies, just swap it for a new one or send it to a PCB repair shop.
If you have any other questions, please reach out to our service team at [e-mail].
Thanks!

[@amrithMilW]

@@HammerheadMachinery
The issue was lose connection. 2 pin in the electronic board was connected with a cap connector. When the machine was working..due to vibration the connection got removed. 😀

[@ybyebrahim3579]

We using atom s.p.a facing oil leakage in machine we can't control this issue give a suggestion

[@HammerheadMachinery]

If there are leaking problems that don't seem to be resolved by the tips in this video, please contact our service department by calling 801-8613-7997 or emailing [e-mail]. Thanks!

[@rezarezae5800]

Sir dear .i thank you so please explain about inside machine i mean about it,s electricite of machine .hope that you will explain insid of hammarhead press machin

[@HammerheadMachinery]

Hi there thanks for reaching out. We will be releasing some more videos within a year for a more in-depth training on these machines. If you need help in the meantime, please send any specific questions to [e-mail]. Thanks for watching!

[@maazbutt9672]

Which Model is this , Head size ?

[@HammerheadMachinery]

This is a 30 Ton Swing Arm. The head size is 24" x 24" but the depth is limited by the table depth. So overall, your maximum die size would be approximately 24" wide by 19.5" deep. Thanks!

[@jennaparsons7612]

Alot of the excuses for leaking oil is ridiculous. All of the reasons for a leak are not the root cause. Seriously terrible.

[@HammerheadMachinery]

I'm not sure if I understand the feedback. This video just addresses the most common reasons (based on a catalogued 5+ years of service calls) why oil most often ends up leaking onto the floor, from what should be a sealed oil chamber. There is no "root cause" as I believe you are defining it is this case, because nothing is malfunctioning. The oil chamber just isn't properly sealed in most cases. There are reasons that a machine can leak due to actual malfunction, but those are not the topic of this video. If you need help addressing a leak caused by malfunction, feel free to reach out to our service department, they'd be happy to help: [e-mail].