Jeep Wrangler Tj | Lj - Best Budget Winch & Mounting Plate Installation Guide (10k lbs Xbull Winch)
ฝัง
- เผยแพร่เมื่อ 9 ก.ค. 2024
- In this video I guide you through a quick winch and winch plate installation on this front bumper step by step! I hope this video helps and thanks for watching!
Shopping on Amazon?
10k winch here:
www.amazon.com/dp/B08RYV6DLW/...
winch plate here:
www.amazon.com/dp/B003CGEQ5E/...
dielectric silicon grease here:
www.amazon.com/dp/B000IID41G/...
winch cover here:
amzn.to/3j65kC8
Official ATEM OFFROAD’s Super Store
www.amazon.com/shop/atemoffroad
More content!
DIY Overland kitchen Tailgate table
• DIY Jeep Wrangler Tj ...
DIY Bolt On Hi-Lift J-Mount Install
• Video
DIY Front Stubby off-road bumper
• Jeep Wrangler TJ - DIY...
DIY Body Lift
• Jeep Wrangler TJ - DIY...
Jeep front and rear shock replacement
• DIY How To Replace All...
Sway bar quick disconnects
• $20 DIY Jeep Sway Bar ...
Overland Tool mounting Solutions
• DIY Overland Trail Car...
Jeep Tailgate table build
• DIY Jeep Wrangler TJ T...
DIY Jeep Rock sliders
• DIY Jeep Wrangler Rock...
How To Install cb radio in Jeep Wrangler
• How To Properly Instal...
32” tires I’m running
• 32” Tires On My Jeep W...
DIY On board air compressor build
• Jeep Wrangler Tj | Lj ...
Fuel and water cell mounting Solutions
• DIY Overland Jeep Wran...
DIY Rear Trail Cargo Rack build
• Jeep Wrangler- DIY Ove...
Hi jack hood mounts install
• Jeep Wrangler How To I...
Wireless winch controls
• How To Install An Opti...
DIY Jeep E Fan build
• DIY JEEP WRANGLER Elec...
#jeeptj #winch #install
DISCLAIMER
Due to the factors out of control by ATEM OFFROAD, we cannot guarantee against improper use or unauthorized modifications of this information ATEM OFFROAD assumes no liability or responsibility for property damages or injuries incurred as a result of any information contained in this video. Use this information at your own risk . ATEM OFFROAD recommends safe practices when working on vehicles and or with tools seen in this video, any injury damage or loss that may result from improper use of these tools equipment or from the information contained in this video
Is the sole responsibility of the user and not ATEM OFFROAD. Be Safe
This video and description contains affiliate links which means if you click on one of these product links, I’ll receive a small commission. - แนวปฏิบัติและการใช้ชีวิต
Heck yeah man, now you can pull out all those JKs and JLs when they get stuck. Sweet shirt design.
Haha 😂 lockers are next I swear ! Lol and for the comment on the shirt , Mrs shields gets all the credit on that one as she was the designer. Thanks for watching!
@@ATEMOFFROAD I think it’s fair to say that she can handle the advertising and merchandise, you can handle all the Jeep stuff 🤣
@@NotICON totally agree!
Perfect, I just came home with my apex 12x and was like hm let’s watch a video first! Good timing 😂🙌🏼
Very cool! Time will tell how well the xbull will hold up to the task , I’m going to give it a beating that’s for sure! Apex sounds like a good winch 💪🏼 👍🏼 thanks for watching!
Little trick, put wires on winch before laying it down on base plate.
Yeah man Grade 8 hardware isn’t cheap but it’s definitely worth the investment
Absolutely 🍻
Do you have an update on this?
Do you happened to know if a smittybilt stinger bumper will get in the way of this set up? Or can I install it just fine?
I’m not totally sure on that one , have to find out if a plate is needed or not! Do you have any more information on the bumper ? Thanks for watching
@@ATEMOFFROAD I’m using my stock bumper and I have the smittybilt stinger on it. I’m wondering if i can use this same winch you have and still keep my stinger bumper or do I have to remove it in order for the winch to fit?
@@eddyrivera7287 I would think it will all fit, but I’ve never seen those stingers that bolt to the factory bumper before! Good luck buddy
The small black wire.. where does it connect inside the control box?
The small black wire with the eyelet on the end goes on the motor on the bottom
@@ATEMOFFROAD correct, but where is the other end inside the control box?
@@derrickarchibeque8942 that black wires is the ground wire for the wireless controls , it goes with the black wire that comes out of the wireless control box and should land on a coil contact then lands on the ground contact of the motor same pole as the heave ground cable fork the battery
Great content,good job!!
Dielectric grease is an insulator… don’t use it on electrical connections themselves like how you rubbed it all over the connector before putting it on. Great idea to use the stuff since it helps prevent corrosion. However, use it on the outside of the connection only! Lol
Thanks for sharing 🍻 you are correct I should have mentioned this better , best to not put it on
the conductive side of the terminal and ok for the rest. It’s been fine so far no corrosion and winch still good as new, just checked it, that was lousy on my part.
Use a product called No-Ox-Id or just No ox. It prevents corrosion but also conducts. I used to put it on giant battery strings in telephone offices. Electricians use it on aluminum cable. You can usually find it in electrical sections of hardware stores.
I use CRC battery terminal protector spray.
What bumper are you running ?
This is the stock bumper I modified to a stubby bumper with some additional strength, thanks for watching 🍻
Spend some doll hairs and get rid of the hook. Factor55 prolink would be a great upgrade.
I’ve been eyeing those and they look pretty awesome! Might just get one . One day , thanks for watching 🍻
part number for the winch plate
amzn.to/3DyWw0G
What’s years your Jeep?
1997
@@ATEMOFFROAD looks awesome!
@@dad3562 thank you
How is it holding up?
It’s been holding great
@@ATEMOFFROAD any problems with corrosion or pulling issues?
@@danraymond1253 no pulling issues some of the hardware is starting to rust
@@ATEMOFFROAD okay cool. I just got one that's supposed to show up tomorrow. I can't wait to get my hands on it. We'll see how it treats me. Thanks for the info!