MechWares - Foldable Support Bracket-Self-Locking Hinge
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- Click and Buy: www.amazon.com/...
Find More Information About This Hinge On: www.mechwares.com
When you enter a home, an office, or even a garage where organization reigns, you simply feel better. MechWare support bracket is ideal for where limitations and/or flexibility in space are critical, apply it on DIY homemade table, folding partition frame, folding door, or anywhere that requires to be folded when not in use.
The spring-activated lock assures stability by locking in the open positions. Folds easily when not in use. To unlock, simply push the latch and fold down.
Specification
Composition and Materials: 12-gauge steel plate
Sizes: see picture
Color: dark bronze
Package Include: 2 brackets
Load Rating: 225kg(500lbs.)/pair *
* These load limits are intended to be used as general guidelines only, and no warranty-expressed or implied. These brackets works better when applied on furniture legs or narrow and simple working surfaces. Wider spacing without supporting of legs will result in reduced load capacity. Actual use conditions will typically result in lower load capacity than laboratory conditions.
Environmental Considerations:
-Environment: Excessive humidity, salts, or other chemical agents can corrode the finish and attack metal or plastic components.
-Fastening: Inadequate or incorrect fasteners can result in the brackets pulling loose and causing damage.
-Alignment: Improper bracket alignment can result in an installation that is ineffective and unsafe.
Nice looking hinges. However, method # 2 is a complete FUBAR. Do NOT install legs using Method #2. The legs wont lock, and screwing into the end grain of the legs is all but guaranteed to fail.
Finally I found it thanks to you..!!!
As far as I can tell, only method one actually locks the legs in place once the table is set up. Method 2, the legs would swing in if you picked it up to move it. Or am I not seeing this right?
This would be genius for a collapsible wall table.
Thank you for this, just what I am looking for
just what I am looking for, to make a small table for me camper van :)
yes, was looking for this too
Yipeeeeee I've finally found the little locking thingy ma giggy I needed... Thank you 😊🎉🎉🎉🎉🎉🎉🎉🎉🎉
Where did you got this pls share the link
@@gargipatilganjare3312 go into the video discription he's added the amazon link
Contact no send
Super helpful. Thanks.
Thanks! I need these on my project :)
is it possible to bend this outwards 180°?
good solution
Great Video , I just ordered 4
Awesome product!
Exactly what I need. Much thanks!
Where to buy from
@@gargipatilganjare3312 Amazon
These are NOT 90 degree locking hinges. While they open and lock at 90 degrees, when you closed them the will not lock in the closed position. The supplier said "just raise the hinge on a block". I tried adding a 1/2" block and that did not make it lock. I then went to a 1" block and that didn't work either. Even after adding a block height of 1.5", the hinge would not lock down.
It appears that the hinge may have to get closed to a 115 degrees or more before it will lock in the closed position. That being the case I would have to add upwards of 2.5" of block to raise the hinge enough to make it fold and lock. In turn, it your looking to get a flat leg fold, that does NOT work.
When shown both the video and raise block pic, the response from the supplier was "Just send them back". TOTAL WASTE OF TIME WOR THESE HINGES.
I'm looking for a similar hinge that has 2" offset built into it. I'm wanting a hinge that will work for a 2" slab drop leaf table. I want the leaf to flush out under the edge of the table. Do you have anything that would work for that?
Would those be good to hold up a 12-inch wide shelf?
Can this be used on a thick perspex?
if I use these for bench press workbench would it be safe?
For weight lifting!!! Absolutely not I hope you are still alive and did not attempt this.
@@codys7591 ha I'm still here. didn't use them after all but almost did a few times.
anyone knows how much weight it can support?
I'm concerned about this as well.. Not shure if I should use those for a ramp
Site claims 500Lbs...however it is a bracket and I assume this is based off a vertical load factor
Why would anyone want to make a table with legs that are locked in the folded position but not when the table are erected?
where can I order it from in India, need it asap????
where can I get the CAD file for this
Please tell me name of this hinge👈
Does anybody know how strong these are? Could they work as a bracket to support a shelf?
These are strong but really too short for a shelf. Look for folding shelf brackets 😁
Amazon ad says 500# but thats downward pressure. Not sure if suitable for a shelf.
where can i have this?how much is this?
lock in one direction
your website is not working
Ye clip kha milege
He is using pliers to make the product seem stiff :D
THE QUALITY OF HING SAME AS SHOWN IN VIDEO IS I RECEIVED IS VERY BAD AND NOT VERY FRIENDLY USER. FIXING OF SCREWS AND OPERATING HINGES IS VERY CUMBERSOME. I INSTALL 4 HINGES IN U SHAPE U SHAPE OF MY FOLDING TABLE AND CANNOT OPERATE ALL 4 HINGES SIMULTANEOUSLY. AND HAD DIFFICULTLY IN INSTALLING SCREWS BECAUSE THE LOCATION OF SCREW HOLES ARE NOT PROVIDED AT CONVENIENT LOCATION. OVER ALL DESIGN OF HINGE REQUIRE PROPER DESIGNING AND GOOD FINISHING. CAN YOU MAKE VIDEO SHOWING INSTALLING 4 HINES ON U SHAPE LEG AND SHOW OPERATING METHOD.?
Name and prise of this bracket in india ?
Amazon
(i think there is something wrong with the person in this video)
Too much shaking of the camera. Poor quality of instructions with all that shaking.....
My adventure with woodworking started with Woodglut.