How to Patch a Chipped Wood Floor | Ask This Old House
ฝัง
- เผยแพร่เมื่อ 6 ม.ค. 2018
- Ask This Old House general contractor Tom Silva patches a chipped wood floor using a Dutchman and hand tools.
SUBSCRIBE to This Old House: bit.ly/SubscribeThisOldHouse
Time: 4 hours
Cost: $50
Skill Level: Moderate
Tools List for Patching a Wood Floor:
Drill [amzn.to/2zjlmkc]
Block plane [amzn.to/2ZalrWB]
Hand saw [amzn.to/31Y2DGX]
Utility knife [amzn.to/31WhtOc]
Chisel [amzn.to/2L9TB2K]
Forstner bit [amzn.to/2TYz6dl] (optional)
Shopping List:
Polyurethane glue [amzn.to/2Zdno4G]
Wood glue [amzn.to/31X8DzN]
Rags [amzn.to/2HotVhR]
Floorboard [amzn.to/2ZncNiT] (same type as rest of floor)
Prestain [amzn.to/31WKCc6]
Stain [amzn.to/2NyJK9s]
Painters tape [amzn.to/2KUaKPn]
Polyurethane [amzn.to/2zjqche]
Steps:
1. Drill a hole through the chipped part of the floor using a countersink bit. Drop a little bit of water in the hole, then add some polyurethane glue.
2. Drive a screw through the hole, securing the floorboard back to the floor.
3. If you saved the chipped piece of the floor, you can glue it back on the floor with wood glue. Be sure to cover all the exposed wood with glue before re-securing the patch.
4. Wipe off any excess glue on the patch with a wet rag.
5. If you don’t have the chipped piece or it doesn’t fit back into the hole perfectly, you’ll need to make a Dutchman. Examine the floorboard and find a section of it that matches the grain around the rest of the floor boards near the chip.
6. True up the edge of the floorboard chosen for the patch using a block plane.
7. Cut the patch roughly to size using a hand saw. First, rip the patch to rough width. Then rip the patch in half so it’s half the thickness of the floorboard.
8. Square one end of the Dutchman using the block plane.
9. Hold the Dutchman up to the section of the floor requiring the patch. Mark the length just slightly past where the chip ends.
10. Cut the Dutchman to length based on the mark.
11. Hold the Dutchman over the chip. Trace around the outside of the patch using the utility knife.
12. Chisel out the outlined section of the floor roughly the thickness of the patch. To save time, you can use a drill with a forstner bit and then switch to the hand chisel for fine tuning.
13. Pitch the Dutchman at an angle and shave off a little bevel on each side with the block plane so the patch will fit easier in the floor.
14. Once the Dutchman fits the hole, prestain it with a rag. Let the stain sit for about five minutes.
15. Stain the Dutchman with a rag. Let it dry for a few minutes.
16. Apply wood glue to the hole in the floor. Make sure all the raw wood is covered with glue. Wipe off excess glue with a rag.
17. Tape around the patch and let it sit overnight. After about 24 hours, add a few coats of polyurethane until the patch blends in with the rest of the floor.
Resources:
Everything Tom used for this project, including the hand saw, block plane, utility knife, and stain, can be found at home centers.
Tom used flooring saved by the homeowner, but flooring can also be found at home centers, lumber yards, and flooring retailers. For a patch, use the same type of wood and look for a piece that has a similar grain to the floor being patched.
Tom secured the Dutchman to the floor using wood glue [amzn.to/31X8DzN] and polyurethane glue [amzn.to/33Wf203], both manufactured by Gorilla Glue (www.gorillatough.com/).
The workbench Tom made the Dutchman on is manufactured by Kreg (www.kregtool.com/).
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers-and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldHouseFB
Twitter: bit.ly/ThisOldHouseTwitter
bit.ly/AskTOHTwitter
Pinterest: bit.ly/ThisOldHousePinterest
Instagram: bit.ly/ThisOldHouseIG
bit.ly/AskTOHIG
Tumblr: bit.ly/ThisOldHouseTumblr
For more on This Old House and Ask This Old House, visit us at: bit.ly/ThisOldHouseWebsite
How to Patch a Chipped Wood Floor | Ask This Old House
/ thisoldhouse - แนวปฏิบัติและการใช้ชีวิต
Hold my beer while I rip a board with my handsaw on the perfectly straight line I drew free hand.
lmao
What a showoff
Watching Tom fixing houses is oddly satisfying. Like watching Bob Ross painting.
Good comparison
"Let's put a happy little 2 x 4 right about...there."
@@markh.6687😂
4:38 I'll just casually draw a perfect line . What a Boss!
Used his middle finger against the wood as a guide
4G64SicKShoT
Thanks Captain ...
Obviously wasnt that obvious. pretentious ....
Obviously wasnt that obvious if people are asking how he drew a straight line
Enchanter Tim and SCWfan06, you obviously failed at reading OPs post before commenting. Way to miss the context entirely.
i think i will trust Tom to even do my knee replacement.
I hope he can match the grain
YES I'M LOOKING AT TWO MYSELF I WAS THINKING OF GIVING TOMMY A CALL LOL.
Tommy is the boss.
Tom Silva is such a class act.
Growing up watching Saturday morning cartoons. After they were over I’ll watch this show. Tom is the only one that ever left an impression
Really? He seems like a bit of a hack to me.
@@randomuser778finally someone understands. Yes he's a TV hack.
“I’ll draw a straight line” RIGHT! I could never hope to do anything as well as Tommy. He is amazing. And this job was done almost entirely by hand! Truly a master.
I had to watch it 3 times just to make sure i saw it right
Was awesome to see Tommy doing much of this work with simple hand tools
It's good to see people on tv use hand tools, it's a good influence for the audience.
Oscar Yuan he barely used them?
Its to keep down dust. Power tools would make a nice dusty mess on everything
I agree. It's kind of funny in shows up in a 3/4 ton GMC pulling a trailer full of very expensive Festool Power equipment, and the only thing he gets out is a handsaw a chisel and a hammer
@@JimDean002I hope the Festool guy does a better job than Mr. Fix It there
I don't have a house nor projects to be done but all of a sudden I need a small hand plane, Gorilla Glue, and that pencil trick and my life will be complete. Thanks Tommy! Love watching these videos, I learn so much. 😀🎉😀
0:21 he was so happy they had the chip
Amazing, "gonna eyeball a straight line" then proceeds to make a perfectly straight line with just a finger and a pencil. If I tried that it would look like a sine wave
If you lock the pencil between your fingers then use another finger to creat the spacing against the board. It's a common carpenter trick and actually pretty easy once you've done it a couple of times.
If you can draw a sine wave freehand that's pretty dope too, tbh
Stop giving away our secrets bro! :D
Chuck Phillips ייחיבכןג
A sin wave would be just as impressive tbg
4:42 sneaks a peak ... shortly after 5:22 "That might be the BEST thing i see all day". We know Manny, we know.
What a workmanship display. Time after time Tommy shows us how it's done. Wish the workers who come and do things were more like him!!!
Tommy never ceases to amaze me.
Tom rips, cuts, trues, by hand. freaking magician.
The screw selection was critical, and they didn't mention a thing about it.
Long enough to go through the floor into the subfloor, but not through the subfloor. Also, threads stopped halfway up, allowing the screw to pull the flooring to the subfloor.
Probably would've used a trim screw myself.
good thing you were here.
people use drywall screws everywhere.
who cares
Anthony Marzella 99.9% of the people who watch these videos aren’t even doing it at home their just watching for entertainment
I'm impressed with the way you ripped the wood with a hand saw.
Tom Silva a true craftsman. You dont find many like him anymore!
She sounded increasingly happy when she saw how well it was coming out.
First I want to say he's an amazing Craftsman that I haven't even begun to match. But I'm a flooring contractor.
The way he fixed the splinter was perfect and spot on.
The Dutchman however in that application. I think would be better served by using a hard drying stainable wood filler.
First I would clean out the area a little bit so the filler is not too thin, and you have something to get roots with. Then lightly sand it smooth, stain to match, and use an artist's paintbrush to draw in grain lines to match the board. Then cover with polyurethane finish. The artist brush and drawing in grain lines has saved me in some really tight spots. That Dutchman would never fly . Looks like a domino in the middle of the floor
Drawling in grain lines with a sharpie or paint brush is only something that a real floor pro knows about or does, much respect bro
Agreed. The butt joint of the dutchman doesnt work visually.
Talks about tight grain needing to.be matched.
Shows tight grain portion that would match.
Flips it over to show the loose grain doesn't match.
Makes final patch with loose grain.
Patch stands out.
At least he is super amazingly skilled cause it still looks good.
i laught so hard when i saw that patch with loose grain after all that speech about grain match LOL
I noticed that too. he made a point of choosing the right end and then he installed the wrong end.
then he adds 'wipe marks' to add grain-look. wtf?
Always a joy to watch a Master at work, they make it look so easy.
Tom is a Legend!!! Thumbnail was him drilling into a hardwood floor with the title "How to Patch a Chipped Wood Floor" Just had to see how he was to pull that off.. Love it!!
Some others discussed that here: th-cam.com/video/DPGxCageub8/w-d-xo.html&lc=UgysxtPVg3Nclq-P4vh4AaABAg
John Wayne was always my hero next to my dad but now its Tom Silva. He is amazing to watch and I have learned so much from him.
this series of shows are some of my favorite and the best television ever produced.. . In my opinion..
Tommy is the man. So much experience, makes it look easy.
Wisdom is an amazing tool. Love watching this guy.
Incredible workmanship. Excellent job as always Tom
4:42 what you looking at 😏😂
Juan lol!
Also why does she need safety glasses?
@@j-bdekker4871 for safety.
Haha busted. She's loving it
Although she was happier with his resawing efforts.
His skill with the pencil is incredible!
Learned a few things...thanks for sharing!
Tom, you are one gifted individual.
Tommy...Saving the world, one Dutchman at a time!
Incredible, talent at its finest.
What a craftsman and really nice man.. give's me faith in America.
Great show, love to watch Tommy do his magic!
Literally before I'd even have a chance to open the stain, my wife would be handing me the divorce papers once she saw that I cut a piece out from her floor
TOM YOU THE MAN!!!
His hand saw work is really awesome!
Tommy is a master carpenter!
watching him draw that straight line on that board with no edge was awesome
I know that it’s for demonstration, but I wouldn’t have even bothered with the patch. Stands out more than before
Mute Stingray that’s because we didn’t the the poly she needs to add AFTER the fact, that makes it blind right in.
I bet it fits tight tommy.!! That glu will expand 🤣
Nice job! Today, I watched the "Dutch door" and "Dutchman floor repair" videos--way to go, Netherlands.
Amazing work! Great advise. I’ll be sure to use it in the future.
I love seeing these little snippets.
Tom loves to show off his perfect ✏️ pencil skills even at his age.
In this scenario, and obviously depending on what floor boards are being used, would it be much easier just taking the whole board out and replacing?
With a hand saw! I bow to thy superiority, my master.
Rolf Bjorn burn marks on the wood. He obviously used a circular saw before camera was rolling
The first patch job was great. The second one wasn't really needed, was a lot of effort for little reward, and only created more work, since it now needs to be stained and poly'd, And honestly that patch work was even more obvious than the last.
Great video.
I would buy a rug instead of the tools.
Or just some black putty and make it look like a natural knot
I’ve been using a sharpie. I have a gold and a black color that I can use to match different sections of the wood.
@@theblogofsingh wood filler and stain it
Such steady hands.
The fit like a glove!
If you had leftover boards at that home, wouldn't it be easier to remove an entire board where the chip is and just stain the new board to match?
On the finished close-up the patch was very noticeable. Personally, I would have simply used a colored filler pencil to fill the damage spot. If that couldn't be done, then I might have tried a mixture of glue, mixed with sawdust, then a light sanding, and finally some stain and urethane
It still needs the urethane finish, they didn't show it completely finished.
I think the lady was very impressed with our boy Tommy!
This Tommy is a true magician!
Just.... WOW!
Master tradesman(and woman) are worth their weight in gold!
"If i didn't know it was there i'd have to look really hard to find it" Hope she can find her glasses though
Yea.... 'bout that
Lets call it for what it is, it's a fixed floor, but it doesn't deceive anyone that havn't lost their eyesight.
It will blend in better after it's fully finished.
I would have to see it completed because with the camera upon it, I could tell it well. I would end up with a rug over that. The video changed at the very end. Very tricky move, but not to a perfectionist eye.
It's an eyesore because it's matt and hasn't had a polyurethane yet. It'll still be noticeable after the finish but not as bad as before.
This guy got madddd skillz. There is no way I would be able to do that without screwing up about 10 times first.
La verdad nadie como tom silva es un fregonazo para todos los trabajos
I love Tommy.
Tommy is an artist!
Loll Tom was so stoked.. he’s like “really?”
Tommy "eyeballs" and draws a straight line freehand better than I can with a straight-edged ruler.
first 2 mins my guy was casually laying game
This man is an artist
The patch does not match at all. The wood floor stain was easy but he did a lousy job on staining. Other than that it was a good demonstration for fixing wooden floor. Thank you.
Nice video on using hand tools. Old-school.
The hardest thing is to find the right stain color...even here we can see that the initial floor had more red color and the replacement is more brown.
proficional ..parabens muito bom seus videos ..
That trick only works under certain situations. I own rental property and some of the floors have no sub flooring. Quite common in my area on houses built between "39 and '47. The floors I've worked on are 2 inch wide, 5/16 thick Red Oak, non groove slats laid on joists. Vapor barrier was tar paper which of course rotted away after 70+ years. Depending on the size of the chip I've used very fine sawdust/glue and stained it... or colored epoxy. So far the repairs have held up for 20 years. Of course your miles may vary.
Wow! Craftsmanship at its best.
Pure professional!! I'd of ripped up the whole floor lol 😂
What's sad, people will look at this and think That's Easy. 10 minute vid, 2.5 hours of set up/clean up. He used old technology to cut his patch. I would have used a circular saw to cut the patch....only because it's easier....not better.
Nice work Tom!
Tom is a master!
Oh, Tom, with these hands tools you are spoiling us.
...add magician to his list of skills.
Really enjoyed this again.
Luckily you have the chip. Luckily you have a left over piece or the original hardwood... ask this old perfect repair situation house.
I keep the chips and have leftover flooring...
this video was an excellent opportunity to show both methods of repair. And most actual homeowners have some scrap flooring leftover even if it was professionally installed. I have a few boards in my garage
I have leftover tiles from both bathrooms and the kitchen as well as wood flooring spares. You never know😩
Perfect 1 inch free hand line crazy.
i wish I knew about that hand plane before I started repairing my table!
Amazing! I know I can't match Tom's skills, but I will try his techniques. I wonder if this will work with factory finished hardwood slats?
Toms just showing off now!!!
At first I thought he used magic to make that straight line but another look shows that he's using his finger to keep it steady but still impressive.
5:03 Now what I want to do is to make her thinner
Home owner: Ok? I need a flying dutchman.
Let me eyeball this perfect straight line😱😱😱
He’s such a man of chat up lines lol 😂
7:59 That's where I lose patience and whack it in there with the hammer. Honestly, I think it had better character before the fix.
cutting wood and installing it was wonderful but after stain mmmm it was obvious that different piece color
Will be better match after a couple coats of poly.
"I would have to look really hard to find it" uhh that patch looked wore than it did before
I would have sanded the cutout and floor together to fill the seams, then matched the stain. it was a good job, just unfinished to my taste.
At 5:36, how did he draw a perfectly straight line!? He is the straight edge. #KingTom
Tom is a damn woodworking magician...incredible talent and skill.
this guy is amazing
She was really excited. It showed on he face !
Great job !!!
Very good job
not really
ماهو قصدك ؟
Beautiful job very neatwork👍