Thank you so much for the video. With the help of the video and a friend, my acuator now has a new motor. However, the gears still do not grab sometimes (usually when slowing down or in a traffic jam) it wether takes a few seconds to find the gear OR - the worse case - it slips into Neutral and stays there - the control light comes on and I cannot shift at all until I turn off the engine for at least 2 minutes. So, actuator motor was replaced, but problem occured again (even though not as frequent as before) gears still slip just as often. From my understanding - the new motor was not "learnt" as we do not own this device shown in the picture. Getting it done at a dealership costs more than the motor for the actuator did and I am afraid that it still will not work properly afterwards. The dealer wants to change everything, actuator, clutch and what not, which will be more expensive than the car was ;) Somebody else suggested to change the transmission oil. What do you think I should try next? Thank you
Hi, hard to say without see the car, important is do the correct diagnostic, check the resistance of the shift motors, clutch aktuator motor, re-lern "ECU replace mode" hold car battery in good condition, check clutch steps.
Hello . What faulty can stopped the intialization and learning at 50% when trying this , the clutch and the clutch actuator are replaced are new ? What can make this happen ? The service told me to replace the MMT ECU of the transmision
Hello. If I move the actuator to clutch clamp position manually following N E M+M+M+M+M E N ( not with electronic tester), sounds need to be heard from clutch or actuator? How do I know the actuator is in clutch clamp position? Thank you!
Hi there! I changed the clutch but forgot to reset the m/t ecu. now the car is in Neutral, and won't change gears. when I put it in drive the N will flash in the dashboard. can you help me out?
Saif Taweel hi, If you have fitted a special clutch kit to MMT system , lern mmt system like after replaced MMT ECU, Everything should return to normal.
hi mate i replaceeee clatch for toyota aygo 1.0 i mark actuator befor i replacee i put bk evrything car was drive 3 days aftar stop on road i bring in gargae i put 3 scanner not commncatoin ,i open clutch actuator looking in side everything fine work can u help me plz??
After replacing clutch, clutch actuator, gear actuator, You have to learn mmt system if not, the mmt system will be lost. You fitted orginal clutch kit?
Aurangzeb B ...this is the Toyota specification 75W90 universal syntetyk gear oil , 99% of the damage comes from the electric motor , especially from damaged brushes. that's why these electric motors work up to about 60k km
Hi i desperatelly need help please. N dissapeared and no gears no nothing.
Thank you so much for the video. With the help of the video and a friend, my acuator now has a new motor. However, the gears still do not grab sometimes (usually when slowing down or in a traffic jam) it wether takes a few seconds to find the gear OR - the worse case - it slips into Neutral and stays there - the control light comes on and I cannot shift at all until I turn off the engine for at least 2 minutes. So, actuator motor was replaced, but problem occured again (even though not as frequent as before) gears still slip just as often.
From my understanding - the new motor was not "learnt" as we do not own this device shown in the picture. Getting it done at a dealership costs more than the motor for the actuator did and I am afraid that it still will not work properly afterwards. The dealer wants to change everything, actuator, clutch and what not, which will be more expensive than the car was ;)
Somebody else suggested to change the transmission oil. What do you think I should try next?
Thank you
Hi, hard to say without see the car, important is do the correct diagnostic, check the resistance of the shift motors, clutch aktuator motor, re-lern "ECU replace mode" hold car battery in good condition, check clutch steps.
Hi again I need ur help I’m confused. I have Toyota Auris 1.8. I replace Cultch motor. Now I’m dash not N display why ?
Hi, before replaced it you used tester for adjusting replace position ? ...if not now you have to calibrate it...
@@FixYOURride13 hi thanks for reply. I test out side motor work with 12 volt I put bk now work There is not fault code. Not N. On dash
@@sara78130 ok but if you lost calibration, must be calibrated
@@FixYOURride13 I did which my scan tool same. I did with 13 pin and 4 pin same
@@sara78130 try making the gaer box ECU replacement / re-lerning procedure, should fix it
Hello . What faulty can stopped the intialization and learning at 50% when trying this , the clutch and the clutch actuator are replaced are new ? What can make this happen ? The service told me to replace the MMT ECU of the transmision
Do you have to tune in the new actuator or is just the replacement.
Video is ok and well done.
But that horrible Sound. Omfg
Pls how do I get the new Toyota corolla mmt clutch actuator in Nigeria ans how much
MaureenIrish Hi, Only from Toyota Dealer. Substitutes do not exist, sorry.
Estimate Cost..? What was the diagnosis till you decided to change it ..? How was the vehicle behaving ..?
I can get it for you
@@edwinagbasi7426 if you can get it in nigeria kindly drop your contact so i can call you. +2348030687111
Hello. If I move the actuator to clutch clamp position manually following N E M+M+M+M+M E N ( not with electronic tester), sounds need to be heard from clutch or actuator? How do I know the actuator is in clutch clamp position? Thank you!
Hi, good question...I newer try without tester.... maybe some one let you know , sorry
@@FixYOURride13 Thank you.
@@ersinali4152 Mine work outside. With 12 volte in side nothing 😑
Select Sensor must be with reverse pins.
hi ,you can expand ?
What does the learning do please? Thanks
Hi, the learning process cleared previous settings and records new parameters for smooth movement. Important ...car battery must be good condition.
is it possible to replace the SMT transmission on MRS 2005 to MMT Transmission?the engine is a 1ZZ
Sorry I never try camper the gearboxs so I haven't clue :(
Hi there!
I changed the clutch but forgot to reset the m/t ecu. now the car is in Neutral, and won't change gears. when I put it in drive the N will flash in the dashboard. can you help me out?
Saif Taweel hi, If you have fitted a special clutch kit to MMT system , lern mmt system like after replaced MMT ECU, Everything should return to normal.
hi mate i replaceeee clatch for toyota aygo 1.0 i mark actuator befor i replacee i put bk evrything car was drive 3 days aftar stop on road i bring in gargae i put 3 scanner not commncatoin ,i open clutch actuator looking in side everything fine work can u help me plz??
auto uk hi, You've tried
're-learning MMT system ?
hi thanks not?
After replacing clutch, clutch actuator, gear actuator, You have to learn mmt system if not, the mmt system will be lost. You fitted orginal clutch kit?
hi yeah today i rest ecu so now its work :)) thanks so much
What oil goes in mate ? ATF or manual ?
Aurangzeb B hi, standart manual gerbox oil, Toyota has a 75w90
FixYOURride13 r u sure not ATF ?
Aurangzeb B 100% it is manual gerbox and we us 75w90
FixYOURride13 ok i. Going to use ATF becouse i think that thik oil will kill actuator !!
Aurangzeb B ...this is the Toyota specification 75W90 universal syntetyk gear oil , 99% of the damage comes from the electric motor , especially from damaged brushes. that's why these electric motors work up to about 60k km
is it possible to change the mmt for full auto
Hi, tooooo expensive.... 🤔
@@FixYOURride13 and the mmt to mechanical ? Is it possible?
Where do you putting oil?
24mm oil cap, oil aut and in is same size .check my onother videos about Toyota gearbox.
@@FixYOURride13 tnx man
Se bon
Great job, skilled mechanic. Thank you for video. Please upload clutch actuator video but this time step by step video. Ok?