I'm working out the connections at the tank. I used to have the 4x4 wood post, outlets and alarm box with the 3 cords (pump and 2 float switches). I have a new septic panel and disconnect to go on the wall like you have. The remaining issue is bringing the 3 cords from the tank (about 6ft from the wall) to the control box, there is no unground "box", just cords coming out of the tank. I bought a 10" round x 12"dp sprinkler box and I'm planning to run a conduit underground and glue a 4x4 sealed box on the end with 3 sealing cord connectors in the sprinkler box. If the float and pump cords aren't long enough, I'll put a sealed splice on them so they are continuous through the conduit with no connections underground. When it comes time to replace one, it can be fed through the conduit without having to dig up all the wiring again. What do you think? I don't see much if anything readily available for the actual tank connections or any videos.
Cindy - NO - A hoot panel uses low voltage to a Sensor Probe and does not use float sensors ... I would strongly recommend that you contact a certified HOOT service provider / installer to assist with replacing that control panel!
So, good information, however, I as a designer and an operator would say that the panel itself is "lacking" as it has No pump cycle counter, no pump elapsed time meter, all of which provide excellent diagnostic information for the service provider. I also prefer a panel that the Hand / Off / Automatic switch is INSIDE the box so it cannot be "accidentally" tripped to OFF or HAND without opening the box. AND Silicone filled wire Nuts !!! too many DIY's use regular wire nuts that are NOT designed to be used outdoors or in a wet environment!
@trapperdavis7706 You seem knowledgeable. A couple questions: 1) how do I learn what type septic system I have? 2) I’m needing to replace the alarm panel on my unit. I was interested in this panel as it couples the alarm and pump electrical in one (our current one is two separate panels); will this unit work? The current set up is an extension-cord-style female outlet that the pump plugs into. I would have figured that direct wiring would have been a more appropriate method. However, with all wires being jammed into a tiny box, I think there’s a link/break in the power. Thoughts?
Great in depth installation video. Thanks for taking the time!
I'm working out the connections at the tank. I used to have the 4x4 wood post, outlets and alarm box with the 3 cords (pump and 2 float switches). I have a new septic panel and disconnect to go on the wall like you have. The remaining issue is bringing the 3 cords from the tank (about 6ft from the wall) to the control box, there is no unground "box", just cords coming out of the tank. I bought a 10" round x 12"dp sprinkler box and I'm planning to run a conduit underground and glue a 4x4 sealed box on the end with 3 sealing cord connectors in the sprinkler box. If the float and pump cords aren't long enough, I'll put a sealed splice on them so they are continuous through the conduit with no connections underground. When it comes time to replace one, it can be fed through the conduit without having to dig up all the wiring again. What do you think? I don't see much if anything readily available for the actual tank connections or any videos.
Your videos are very useful and informative! Would you please consider making one with all the bells and whistles???
Great Information
Yay! Thank you!!🎉🎉🎉
I have an aerobic hoot system and the panel is falling apart…will this be the same install procedure?
This will be a little different same principle we will have more panel how to videos coming out as we see a need for them
Cindy - NO - A hoot panel uses low voltage to a Sensor Probe and does not use float sensors ... I would strongly recommend that you contact a certified HOOT service provider / installer to assist with replacing that control panel!
thanks for this, the installer didnt give me a walkthrough
So, good information, however, I as a designer and an operator would say that the panel itself is "lacking" as it has No pump cycle counter, no pump elapsed time meter, all of which provide excellent diagnostic information for the service provider. I also prefer a panel that the Hand / Off / Automatic switch is INSIDE the box so it cannot be "accidentally" tripped to OFF or HAND without opening the box. AND Silicone filled wire Nuts !!! too many DIY's use regular wire nuts that are NOT designed to be used outdoors or in a wet environment!
@trapperdavis7706 You seem knowledgeable. A couple questions: 1) how do I learn what type septic system I have? 2) I’m needing to replace the alarm panel on my unit. I was interested in this panel as it couples the alarm and pump electrical in one (our current one is two separate panels); will this unit work?
The current set up is an extension-cord-style female outlet that the pump plugs into. I would have figured that direct wiring would have been a more appropriate method. However, with all wires being jammed into a tiny box, I think there’s a link/break in the power. Thoughts?
1.5 hours to do it... 2 months to deal with the code people... (if your location allows a non-licensed electriction do it at all).