"Windows Could Not Format a Partition on Disk 0" Error Code 0x80070057 ||Windows FIX 2020||
ฝัง
- เผยแพร่เมื่อ 24 ส.ค. 2024
- Hello guys thank u for watching ||Don't forget to SUBSCRIBE and hit the bell icon||........
As I have promised in the video i will be providing commands here....
1) Press Shift + F10 to launch the Command Prompt.
2) Diskpart
3) List Disk
4) Select Disk 0 (Select your required Hard Disk)
5) Clean
6) Create Partition Primary Size=200000 (In my case I will be creating 195GB for C drive)
7) List Partition
8) Select Partition 1
9) Active (Make the C Drive Partition Active)
10) Format FS=NTFS quick (Format the drive)
11) Exit (Exit from the Diskpart)
12) Exit (Exit from the Command Prompt)
13) Refresh the Windows Partition Wizard
To Join with me on Twitter||
/ himal_dangal
To join with me on Insta||
/ himal_dangal
Thank U for Watching Jay NEPAL .../\
![[TH] 2024 PMSL SEA W2D2 | Fall | เครื่องร้อน พร้อมลุย](http://i.ytimg.com/vi/JO2_bLow_1Y/mqdefault.jpg)
Hello folks Please help me to reach 1k subs. Im really close to that mark. Thank You and Stay Safe ❤️🏡
@Evil Gaming if it disk C the storage in disk C only deleted otherwise disk d or other will not be deleted
At 1:05 you say press shift + what???
F10
Hard disk dekhacche na keno????
@@HimalDangal24cmd doesn't appear while pressing that
May 25, 2023. Still works like a charm. No time wasted. +1 good sir.
2023 and still works! thank you very much, bro.
says. " Disk part has encontered an error ( Wrong parameters) Se the system event log for more info. Doesnt work for me.
This happened under the format fs part
Hello did you get any solution for this error?
My laptop was too slow to install anything and the CMD took some time to work, but eventually I was able to reinstall the Windows. Appreciate the instructions!! Keep up the good work!! 👍🏻
@sthembiso tshabalala BIOS, Boot Page or Partition Page - You have to press Shift + F10 to bring up the CMD window.
It doesn't appear while pressing those buttons
This one deserves a like and subscription, this method worked after I nearly threw this drive to the bin and firm handshake 🤝 sir
You're welcome!
Thank to you for helping me with your solution..
Your video is straight to the point 👊🏼
Not wasting my day
2:07 it says "DisskPart has encountered an error: A device which does not exist was specificied. See the System Event Log for more information." Even tho the device DOES exist
Bro whenever I type"format fs=NTFS quick" the error occurrs and the error is "the parameter is incorrect" so please can you help me out?
Hello did you get any solution for this?
Getting nearer to the 1k subs Need your help guys ❤️
Thank you Greetings From Nepal 🇳🇵
Thankyou brother you. More videos please to help others like me thankyou godbless
Welcome Mate
installing windows server 2022 in 2024 great tutorial!
Damn!! Thank you so much!! 2022 it's still working. God Bless you man.!
Gracias mate 🙌🏽
I went to many shops already but they can't fix it. You're a life saver man.
Yeah it happens….it is not a physical hard drive problem so, some of them may not know about this… or they just ignore it so, someone buys new hard drive through them
@@HimalDangal24 yeah right. They're just damn lazy. 😂. Well thank you again.
That DISK pronunciation caught me off guard.
When formatting it says; Diskpart has encountered an error: The parameter is incorrect. See System Event Log for more information.
Its same for me
Go to bios then select reset to default settings and then save now go as he commands and make sure u create 2 partition then active the first one and then format it ...it will work
bro when comand format fs=ntfs quick that is not sucses. “disk part has encountered an error :parameter is incorrect see the system event log for information. can help me?
Did you solve this issue
after quick format i get "dispart has encountered an error: the parameter is incorrect.
After clean I got also same Error which is "windows cannot be install on drive 0 ". Plz help me
Diskpart has encountered an error: The parameter is incorrect. See the system event log for more information
I'm having same problem
mine displays diskpart encountered an error and the settings are incorrect
When I type clean I keep getting "diskpart has encountered an error: a device which does not exist was specified. See the system event log for more information. "
Me too
Did you find the solution brother?
Just restart pc and then repeat steps again , Your welcome.
Help
Sir i have prblm after writing this command format fs=ntfs quick 0 percent completed and diskpart has encountered an error
Please give solution
This video was so help helpful, i finally i managed to install windows to my laptop. thank you so much
But you didn't have any windows before you did this tutorials?
Bro last format fs=ntfs only confirmly come don't use quick
This is the best man! I don't know but I think I'm having issues about my HDD. I'm having black screen of death a while a ago and now this, you saved me! Thanks man!
After hitting the format cmd promt
I got this error" diskpart has encountered an error: The Parameter is incorrect....& One more line
Plzzz help🙏
Finally done......after this error saw, i removed my sd card . And put it again in my mobile. It says that this card is not supported. We have to format. And finally card got formatted.....
while entering shift+F10 CMD doesnt open
Just disconnect your hard drive & connect it back. It worked for me
After cleaning it said “Diskpart has encountered an error: The system cannot find the file specified.”
same here. help us
Same
@@vikashsinghrajput2930 you might have more than one partition like c or d or f just keep 1 partition then try i did the same as i face same problem as you
remove quick when typing format fs=nfts
when i typed the clean comman it said diskpart has encountered an error: A device which does not exist was specified
@Marissa Ficarella Did you find a fix?
I failed 54 times with that error now I got it and changed to legacy mode
Diskpart has encountered an error while using command format fs=ntfs quick
Same
Same
Type the command without quick
@@technicalplanet1581 it sticks after zero percent
Thank you so much for this video
My laptop was down from last 2 month .finally ok just because of this video.
Thanks a lot again.
Welcome. Im really happy that this video helped you
when i clean, it says diskpart has encountered an error: a device which does not exist was specified
Tnx a lot.
2022 still works!!
Bro I finally fix it, what I recommend after all the process is done and click refresh just click x and go back to reinstall windows
bro you are genius ! my damn laptop waked up after 2 years , thank you so much
Cheers brother 👍🏽
I have a problem during forma
It shows disk partition encountered an error
just type format fs=ntfs
Thank you soooo much it's been 3 years to run this hdd❣️❣️❣️
Welcome mate
& please don't forget to help me by subscribing my channel CHEERS
🙏🏽
My disktop showing this problem
Diskpart has encountered an error : The parameter is incorrect.
See the system event log for more information.
You are great you saved my life and my computer. I was thinking that I have to buy a new hhd. Thanks again.
Nice bro. Welldone. Appreciate the help and the code typed on description
when is use Format fs=ntfs it said
0 percent completed
Virtual Disk Service error:
The device is in use.
The selected volume or partition is in use.
To continue with us operation use the OVERRIDE parameter.
Got an error "DiskPart has encountered an error: The parameter is incorrect. See the system Wvwnt log for more information" Please help...iv been struggling with my laptop for over a week now...
same
Windows could not format a partition
Same
Bro did you find where is the problem
@@makmo3gza I had also same problem , so I removed storage device from the machine and formatted from anather machine , it worked for me 👍🏻 ,let's hope it will work for you !
When I do clean it comes up with ‘diskpart has encountered an error: the request could not be performed because of an I/O device error. See the system event log for more information’ can you help me I don’t know what to do and I don’t know how to see the system event log.
Same
have you found a solution? i have same problem
The only solution I have which worked for me was getting a new SSD.
Sir, I am unable to format my partition in which I want to install new windows. When I went there it is showing "Windows could not format a partition on disk 0" , so Sir ,plz tell me how can I format that partition without loosing data of other partitions...
Plz answer as soon as possible..
This problem is "windows cannot be installed to this disk. The selected disk has an MBR partition table.On EFI system,windows can only be installed to GPT disks"
after creating a partition, i had an error, diskpart has encountered an error: data error(cyclic redundancy check)
There are so many videos about this error on YT, but only yours have figure formatting RAW to NTFS on your command prompt. Glad I followed yours! Thanks for your details explanations, even tech-dummy like me can follow!👍👍👍
Welcome And Please Don't forget to help me by subscribing my channel
If you don't see that Partition hit Refresh, then it will pop up. Thanks for the video also man
It says diskpart has encountered an error, the request could not be performed because of an I/O device error
Check if you have driver of hard disk installed
sir please reply .. what if is didn't want to clean my entire disk , i have some important data in disk .. I just want my data... and i just wanted to clean the c (system) drive
While doing format fs=ntfs ,it has stop at 0% for long time
same, did it completed or is it stuck at 0% forever?
Diskpart has encountered an error
bro this has came what shoudl i do pls help me
DiskPart has encountered an error: The parameter is incorrect.
See the System Event Log for more information.
Same, any solution?
@@rachidzogari6777 no man i looked for an solution for this problem and at last i threw away my hard disk
@@rachidzogari6777 anyone got solution i also have same problem
great job sir....its work i have fixed my issue with the help of you.
thanks again....
Welcome mate
I made it all the way to formating the partition and i typed in the command snd it says "diskpart has encountered an error: the parameter is incorrect. See the system event log for more information" please help!
Hlo sir ji setup cannot continue due to a corrupted installing files. Contact the vendor of your windows installation disc or your system administrator for assistance error
When I use the command format fs=NTFS...
Show diskpart has encountered an error
Same
@@tusharbartakke2797 bro I got the solution type the command without "quick"
Same
Hey it was working good up to DISKPART> clean. but after that it says, Diskpart has encountered an error: the request could not be performed because of an I/O device error. It doesn't even start from the first place. Any help here??
Am I supposed to format the Disk that holds the Windows??
Thanks 100 percent working
After I refresh, it won't let me click next. It says windows can't be installed on drive 0 partition 1 can u help me?
After format command
Its saying that 'the disk service error cammand deleted
Me too man
Thank you so much I tried so many things and this FINALLY worked..THANKS :)
Awesome.. bro thanks..
Thank you sir.. you saved me form a big issue😊.
Most welcome 😊
create partition size after that its * or =
You are really good person 🙏 thanks 💕 for your help brother 😘
while formatting it is showing diskpart encountered an error please help
Damn it not working... DISKPART HAS ENCOUNTERED AN ERROR: THE PARAMETER IS INCORRECT SEE THE SYSTEM EVENT LOG FOR MORE INFO...
NEED HELP!
Restart the pc and repeat the same steps
Mine too
same here
Its helpful for me with legacy mode thanks a lot
Not working for. Cannot proceed w/the setup
Format fs=ntfs quick dewar por error ashche. Parameter incorrect dekhay. Akn ki korte pari?
oh my oh why, i did you did but i still cant install windows coz it says MBR.. u have to convert it into GPT...
so convert it its all easy
Sir please help me sir after doing this my hard-drive is not showing during installation and also in bios and this pc.
Sir when I eneterd the format command it show that an error occurred
What partition do I make if it’s 119gb size but says 0b free
Thanks dude u helped a lot 🥰
Love from india !
Cheers mate
Love from Nepal 🇳🇵
disk part encountered an error because I/O device error, where can i find that repair
Hello did you get any solution for this?
If I type Clean and then press Enter then what will happen to my files inside my Harddisk?
We are force formatting the partition...... And everything inside will be deleted
@@HimalDangal24 is there any other method to get my all files from that Harddisk and I format it?
Use hard diskcase and plug it to another pc and save files.... You have to buy Hard diskcase
@@HimalDangal24 thanks
Still problem not solved 😕
Error shows again
But bro copying files stuck 0 percent fix plz 😢
I could not open cmd with shift+f10
Try shift+fn+f10
Hi,what’s the combination at 1:04? Shift+Alt?
Shift+F10
You saved me. And my time too. Thanks
I tried it but problem not solving. Again same error.
Awesome! Its really worked…tq Sir
mine displays encountered an error it is a dell latitude e6430 that I have
Thank you...this video helps me very much...💜
Thanks man you really are amazing,Thanks a lot I subs
Welcome brother
Bro I typing fs=ntfs but the Percent is 0 and the parameter is incorrect
Hello did you get any solution for this?
thank u very much, its really work, .. big help..
Glad To Hear Mate
my disk controller is not enable so iam going to bios but iam not find AHCI in my bio Iam only find ide plz help me bro
Sorry mate I don't have any idea.
As far as I know AHCI is not available in all bios system.
But bro iam used another hdd in my computer and it really work and faster
So i want ask you how it work
After commanding Clean will it delete all the files inside my Harddisk? I am Confused bro plz Help here
Yeap
this method does not work on my computer. Please help me.
It says parameter is incorect while formating help pls
Please help me
After 0 percent completed, it's saying
Diskpart has encountered an error: the parameter is incorrect. See the system event log for information.
Please help me out
Hello how you fixed that?
@@the_doctorstrange I didn't.. actually I encountered another issue that's what I'm asking
@@yougotitright4346 I'm facing the same parameter is incorrect error? What you did to fix this error?
@@the_doctorstrange I left it as it is 😂
But I'm sure if you leave it for more than a month these commands works easily that's what I have experienced from my recent problems
Thanks bro so so much!! VERY HELPFULL
Glad to Hear ❤️
Next hocche na PC on o hocche na eta Kore. Ekhon ki Korbo ? Please tell me.
Thanks brother ☺️☺️ awesome
Welcome And Please Don't forget to help me by subscribing my channel