ฝัง
- เผยแพร่เมื่อ 10 มี.ค. 2017
- A customer wanted to have a servo move to two adjustable positions for a cosplay helmet he was making. I made a modification to my standard "Toggle Switch Servo Positioner" so that it would have a speed control. This way the servo could move the part at a rate that made more sense for the helmet.
This is the link to the part in my web store:
www.freewebstore.org/heyok-pe... - ยานยนต์และพาหนะ
I have one of these 2 pot versions for my kylo cosplay helmet. works a treat. Just ordered this new speed adjustable version too
Interesting video. Since you are knowledgeable in this area, I have a question. I have an, on-off-on toggle switch that I need to control with a typical servo. Currently I am operating it with a 2-56 threaded rod and a clevis, is there something made for this that I'm not aware of. Thanks for any information you may have.
Hi, I can try and help. Please email me about this and I will see what I can do. mostlyal@gmail.com
Hi can you tell me if you could post this to the UK? Also could you tell me once the servo meets it's end point. Is it still consuming power i.e. is there still a signal being sent?
Jon Wright Hi Jon, please write me at mostlyal@gmail.com and I can be more helpful. Yes I can post to the UK. The servo still uses some power when it reaches the end point. The more a force is trying to move the arm, the more power it will use even if it isn't moving.
Hey buddy, is there any way you can show how you have the pots wired up? I'm looking to duplicate the exact same thing.
The pots are wired between positive and negative of the power supply. The wiper is connected to an analog input on the micro controller.
What is the part called that you was using to control the speed ect? Thanks
Hi. It's a part I make and sell in my web store. You can find it here: www.freewebstore.org/heyok-performance/Servo_Positioner/p1742582_18227999.aspx
I am not very experienced in this area. Could put a different on/off switch on it. Or does it have to be that one?
Hi Nathan. Yes, you can use a different switch. I make a few versions of the controller. I can make it respond to a momentary switch closure or a latching switch closure. Email me if I can be more help. mostlyal@gmail.com
Hi. Can i replace the switch you are using with a simple on/off switch ? If not, what is the type of switch needed ? I bought your product but i need to change the switch and i'm lost, there is so many type of switch available on Aliexpress. I don't understand why you are using a 3 pin switch. One last question: Does the battery drain while the motor is not moving ?
That should be fine. Please email me and I can be of more help. mostlyal@gmail.com
Is there anyway to hook up two servos to a single controller? I need to have two servos to move in the same way, same time, and this configuration is perfect for what I need.
Sure, just use a Y cable or I can build you a controller with two outputs connectors. Contact me at mostlyal@gmail.com and we can get this going.
@@heyok thank you! This helps a lot, I will use a Y cable.
Is there anyway you could show a set up, where you press a tactile and have it spin 180, then when you release it, it spins back?
Sure. Just replace the toggle switch with your tactile switch. For 180, you would probably need the end point adjustments set to their max positions. I don't have one of these controllers built up at the moment so I can't really make your video right now. Contact me at mostlyal@gmail.com if you need me to make one of these. Thanks, Al
heyok Thank you for the help, I’m pretty crafty, so I’m sure I’ll find a way to make it work.
It servo driver i was looking for. Can you pleaseshare me the schematic of that driver my friend. Or even share me the link if it available on internet. Thx
Hi Dian, I'm sorry, but these are things that I manufacture so I can help feed my family. If you want to contact me via email, I might be able to make you something: mostlyal@gmail.com
can you send circuit diagram of position controller use in this video
I build these parts to help put food on the table, so I won't send you a circuit diagram. I would be happy to build one for you.
Hi, anyway of using a 3 position toggle switch so that it goes left and right and back to neutral?
Yes! I also make a three position version: www.freewebstore.org/heyok-performance/Servo_Positioner/p1742582_18227999.aspx
@@heyok thanks for the quick reply. Can I use this with an existing transmitter and receiver setup so that the toggle switch overrides the transmitter when I need it to?
@@Garfoid Welcome! It only works from the toggle switch. Maybe email me if I can make you what you are describing. mostlyal@gmail.com
Can you make this servo speed controller use at Rc receiver,?
I'm not sure I understand your question. Why wouldn't you just plug the servo into the RC receiver? If it is easier, send me an email: mostlyal@gmail.com
Can you link all the supplies these are exactly what I needed and I cant seem to find them
This is a part that I sell. If you would like one, you can find it here: www.freewebstore.org/heyok-performance/Servo_Control/cat1742583_1590422.aspx Also, feel free to contact me at mostlyal@gmail.com
@@heyok so the servi toggle switch on your website the 15 dollar one you can connect to servos to it
@@samanthap1227 I think I describe it pretty well in the web store, but it is like this: You can connect two servos to one servo signal. The toggle switch lets you choose which servo connects to the servo signal. Email me if it isn't clear as it easier to include pictures to help explain.
Hi good afternoon could you tell me how much it cost me if I wanted you to produce 20 of these exactly like you do have it in the video above electronics
Hi Bradley, Please send me an email and I will help. mostlyal@gmail.com
Or, you can find that part here: www.freewebstore.org/heyok-performance/Servo_Positioner/p1742582_18227999.aspx
I would like to purchase one of these.
Lucky me!
it be possible to hook it up to a 12 volt model railway controller
Does it supply from 5vdc to 9vdc?
To the best of my knowledge it is the standard Hornby train pack controller that you get in any standard Hornby set from the earlier Generations when it was the old black Style
Also I just looked at the link you sent me do I get all parts seen in the photo or is it just the component in the middle
@@brickleyyard4966 The controller only. Any questions, please email me: mostlyal@gmail.com
@@brickleyyard4966 Like I said, please contact me via email and I will help all I can. In case it didn't come through in my last reply, email is mostlyal@gmail.com
how do you make it
Carefully! This is a product that I build and sell. I program a micro controller with software that I created and I build the hardware. Can I get you one?
Do you have an online store for these?
I have an online store but this part isn't in it. Send me a note to mostlyal@gmail.com and I will help you.
I need to change my answer. The part is in my store: www.freewebstore.org/heyok-performance/Servo_Positioner/p1742582_18227999.aspx
hi im from ph how can i buy?
Hi Jaycee. Either email me at mostlyal@gmail.com or buy from my web store: www.freewebstore.org/heyok-performance/Servo_Positioner/p1742582_18227999.aspx Thanks!
Do you still make these?
You know I do !! For others, this is the link to the store: www.heyokperformance.com/Servo_Positioner/p1742582_18227999.aspx
Are you selling these
Yes. Find them here: www.heyokperformance.com/Servo_Positioner/p1742582_18227999.aspx
just send some question to your facebook messenger. Please reply thank you
Sorry - I don't see anything from you. Please use email: mostlyal@gmail.com
just send yo a email to above