Sadly I slung the chain on my gsxr at the end of last summer and is slapped a small hole in the engine case and since replacement engine cases are so expensive I believe high temp jb weld epoxy will be the way I fix it
Hi bro ...in the area of engine oil drain bolt .. there is a crack due to over tighten ... Now it started leaking ... No I am using mseal to fix it .. but not satisfies ... Want a permanent solution ... Can you the share the link of this ... Do yu think this will help my case ... Pls share ur idea
I am having the same problem talked to a few people said drain the oil put it on her it on watch the oil leak and see if it leaks be aware and see if it leaks to top off I am doing it tomorrow
@@jeffbezos4746 yep. And I’ll weld it every time before I JB weld anything ever again. And if you happen to use JB weld before having it properly fixed good luck. Because you have only made it worse by using it.
@@nicholaskominski3746Until you know how to etch the surface of the damaged area, then most likely you would feel that way. Take a Dremel and grind out the damaged area and clean it with PVC primer and the JB beats having to split the cases to weld it.
@@about2mounti have a cracked engine just infront of the front sprocket. I used jb weld and it still leaks. How do i get it off the best way to weld it properly.
Did it hold high pressure, did it work
Sadly I slung the chain on my gsxr at the end of last summer and is slapped a small hole in the engine case and since replacement engine cases are so expensive I believe high temp jb weld epoxy will be the way I fix it
Did it work for you
Did it work?? Same thing Just happened to me today on my R6
@@LangeLS4 it did but I also warped my front sprocket output shaft. Jb weld steel stick and rtv sealant worked
@@pmm4177 so you mixed those two together and slap it on.?
Hi bro ...in the area of engine oil drain bolt .. there is a crack due to over tighten ... Now it started leaking ... No I am using mseal to fix it .. but not satisfies ... Want a permanent solution ... Can you the share the link of this ... Do yu think this will help my case ... Pls share ur idea
Same problem
Same problem
Hi I’ve the same problem did you manage to fix it if so how ?
I am having the same problem talked to a few people said drain the oil put it on her it on watch the oil leak and see if it leaks be aware and see if it leaks to top off I am doing it tomorrow
Same problem, a little hole next to the drain hole
Awesome vid and edits and filming and motor
Wher we will get this ... Link please to buy
Will this work on my kia sorento engine
no it is temperature sensitive will not work
Apa nama gam tu abg sbb enjin motor saya retak
how many days will take it to dry?
It sets in 4 minutes and cures in 6-8 hours
run the engine for 2 minutes, the heat will cure it
I will try this methoud my bike same problem engine case crack
This is sure Sullition.. How much this gum prize sir
How did it go for the bike?
enjin berape lamu boleh tahan ni
High temperature proof?
Yes
Tahan suhu panas ke?
Did it work
yep
Kedai area mna bos. Boleh dptkan no phone x
Mera pulsar ka engine halka crack ho gya hai aur leak hora engine oil main ise kaise thik karu
@Salman Ansari welding karane ki jarurt ni hai na
@Salman Ansari ok mere oil drain bolt ke paas minor crack hai engine oil khali krke lagana hai kya
@Salman Ansari ok thank you
@Salman Ansari 🙋
Bro koi solution mila...mera bhi same prblm hai...
not working absolutely waste of time instead go for aluminium gas welding for permanent solution
Absolutely the worst way to repair a crack in aluminum
Have you tried it?
@@jeffbezos4746 yep. And I’ll weld it every time before I JB weld anything ever again. And if you happen to use JB weld before having it properly fixed good luck. Because you have only made it worse by using it.
@@nicholaskominski3746how would u permanently fix it
@@nicholaskominski3746Until you know how to etch the surface of the damaged area, then most likely you would feel that way. Take a Dremel and grind out the damaged area and clean it with PVC primer and the JB beats having to split the cases to weld it.
@@about2mounti have a cracked engine just infront of the front sprocket. I used jb weld and it still leaks. How do i get it off the best way to weld it properly.
it will not work. when the engine heat up it will become like a bublegum
Have you tried it?
@@jeffbezos4746 yes