8kW at 120 volts is 66 amps but the secondary wires only look big enough for about 2kW or am I missing something? Also, at 50hz the transformer appears to be 1000VA at the most.
Very , very good!. But I think that the circuit is good or capable to handle the 8Kw but the transformer is not big enough to handle that much load. One reason for that is that with no load the inverter gives 110v and with a couple of lamps ( maybe 200w load) the voltage drops to 106v. Some form of restriction the circuit has but overall very good and thanks for uploading the video.
IRF Fets IRF44N have a Vdss (Source Drain Voltage) 55 Volts I'd be very hesitant running these fets with a 48 Volt supply rail. (even in a bridge) for a start. AND as a parting shot to the Keyboard Cowboys --CONGRATULATIONS - YOU BUILT IT!. (From an retired engineer who used to design these circuits ) PS. Suggestion for an inexpensive transformer source REBUILD the secondary of an old microwave oven. Should be good for about 1KW .
don't microwave oven transformers have a gapped core as current limiting? would that not present a problem of overheating the windings when used in this manner
@@drspastic Another of the many problematic aspects of this build. At low flux levels would be ok BUT leakage inductance can be problematic. I like the idea but there are MANY DEVILS IN THIS BUILDS DETALES. At HIGH AMPS 1oz Copper PCB (usually used} Is NOT the ideal construction medium which I see used a lot.
@@drspastic Yes BUT the core is a start. The Primary becomes the secondary and that leaves the PRIMARY to wind. Remove the shunts. The core I used was ungapped although it was not (ideally should have been) interleaved. (Welded) This was an Heath Robinson build for me. As I said these builds are full of PROBLEMS for the inexperienced. Even some commercial units are ?
@@ab_ab_c My suggestion is get some CHINESE MODULES. It doesn't make for a "NICE BUILD" but they have sorted all (hopefully) the problems out leaving the POWER STAGE for you to build. I like to use COPPER BUSSES not the PCB. These have also a small heat removal advantage and importantly low stray impedances (Which can result in parasitics) that can cause problems in these ckts. 8KW at 125V 60Hz is not a problem HOWEVER What and HOW LONG DO you need it to handle OVERLOADS when eg. A motor starts up. At 8KW you'd need to get probably a custom transformer which you can always UNDER RUN (Reduced power ) as you add more current capacity to the power handling devices over time/ Remember these are POWER CKTS and if yo can WELD STEEL of an outlet think of what this could do with over ¬6X the power.. It is not pretty when things go catastrophic
I think he means the circuit can not the transformer because the transformer is a 350 watt transformer the more load adding the lower the voltage get because the magnet field is getting weaker he need a bigger transformer with bigger wire to conduct high current making the field much stronger to handle heavy load but am not a fan of heavy transformer core it’s better to use ferrite core and make a two inverter circuit the voltage drop is very little compare to bigger heavy iron core transformer that have a lot of losses in energy
the circuit in pcb like the mosfets are just driver as well as the spwm that generate the pure sine wave. but the real part that generate the high output wattage is the transformer with feedback to stabilize the generated power
Good job I have a question about pin 5 and 9 I want to use 300 volt mosfet to use a 270volt but pin 5 and 9 is my trouble but they have to connected to mosfet drain and am using high voltage so am asking what is best use a buck converter or resistor
I have a question because I want to build one from old microwave parts. Shouldn’t this have a fuse and what kind? Should there be a fuse for the AC side and DC side. I want to build a whole home solar grid. I would like to do this safely.
Question why mosfet like irfz44n can’t inverter with 20 volt and the data sheet said 50 Drain to source but anything over 14 volt blow out the mosfet is that mosfet voltage ratio is not in inverting mode but switch mode
No knowledge about the transformer you used . When you test you must use a heater or a motor 4 or 5 KW but you used lamps all of them are less than 500W .
Ciao.il tuo inverter e interessante .ma per realizzArlo devi dire dove posso comprare tutto il materiale anche quella scheda elettronica che tu metti dove si può trovare ci tengo ad una risposta .
La tarjeta driver esta perfecta... Pero el dimencionado de los cables del transformador a la tarjeta es muy pobre... Y eso hace que pierda potencia (de 110 se baja a 104 voltios) le recomiendo hacer la tarjeta de potencia por separado
I tested the low frequency inverter that I designed but the out put is giving me 106v and when I connect filter capacitor of 5uf the out put dropped to 83v without feedback and when I connect the feedback the out put go up to 85v and the the feedback voltage is 2v minimum. What could be the issue while the out put can't go up to 200v. I used spwm module. Thanks for your reply
There are some concerning things here. The mosfets should be electrically insulated from their heat sinks. When you follow the link back to where it is claimed the circuit diagram is, you find only the pcb pattern and an image of a purported “free energy device” (nonsense). TechBuilder has a better design and tutorial, with better safety practices.
Ciao.sarei interessato a questo tipo di inverter.per favore puoi dirmi dove posso comprare tutti i componenti per poterlo realizzare compreso il circuito stampato.spero che mi dai una risposta grazie
While the concept and design is practical, the cable size and the transformer are impossible to support 8kW, it is make sense for the system displayed to support 4kW for 48V system but 8kW is way off.
Yo vi mucha gente asi . Muchas preguntas y ni una respuesta .solo quiere seguidores . Mi pregunta es cual es la entrada y la salida del transformador y como puedo tener el diagrama para acer una .con la respuesta yo creo .gracias
8 kw. ? 8000 / 110 = 72,72 amp.When you remove a rabbit from that transformer, 72 amps will also come out. 48 v from the input of the transformer. 166 a. You are entering... I hope your teacher has not seen this video. He would say he was wrong about electronics and commit suicide.
Sei bravo a presentare il video ma quasi tutti non siete chiari nel spiegare i particolari .ad esempio dove posso prendere lapiastra circuito.laltra schda piccola cosa e.poi alla fine metti unaltro inverter o cosa il tutto non è chiaro.
i learned from the TH-cam how to convert DC to AC for the first time using a tranformer with 2 NPN transistor its worked I plugged a 240volts glob the lights come on buts it’s flicking I wonder why i worked it’s out something to do with a resistors its wasn’t right I using the ohms laws put its together to get the right one it’s worked it’s never flicking a gain i things why didn’t the TH-cam explains its how to worked its out to get the correct resistor maybe they things it’s may cause Brian’s damage the nexth my invention is how to make its powers to drive a 2000 watts heaters
Yes, truly magnificent, the colors, all these little black things contrasting with the green, and the beautiful music. What I didn't understand is..... what the fuck is it for?!!!
Please help.. We need your help. I dont know how to do that and i dont have any idea about like this video, but my brother's and friends said that can you make a per video step by step tutorial building a 48v 10,watts if you can or let say 8,000 watts so that we can make or follow step by step your video and so that we can make a high capacity inverter to run stable our house. Please and we will help you and your channel to promote here in the Philippines for more subscribers, likes and comments. If you can, please make it sure step by step especially what devices or materials to buy so that we complete all even the wire and etc cause we dont have any idea, we creating base on your video. Hopefully you can help our request cause if we buy a inverter is so expensive. So that we can run our 1 Inverter type of refrigerator 1 Inverter type of Freezer 1 65 Inches Samsung Smart TV 1 amplifier and sound system with 2 big box of speaker and 6 small speaker 4 electric fan 5 ceiling fan 5 pcs 20watts led bulb 3 pcs 15 watts led bulb 5 pcs 9 watts led bulb 1 of 1.5hp water pump or induction motor Please make this as our request.. Step by step so that we can understand. Please input all the devices or materials. Thanks and god bless you sir/maam I hope you can make this within this week. We are so excited. Please email me at pimentelarvin@gmail.com or mention me so that we know that your done creating and uploading our request. Once again. Thank you 🥰💪👏
Nice job! And you get extra points for good music.
Nice, but you would have won my heart is you displayed waveform on full load.
8kW at 120 volts is 66 amps but the secondary wires only look big enough for about 2kW or am I missing something? Also, at 50hz the transformer appears to be 1000VA at the most.
666A 12V.
Well, don't the 4 bulbs demonstrate a power of 8 kW? :)
this Transformer is max. 600 Watt
@@dimmer4955 It should be SUPER BULBS ;)
Very , very good!. But I think that the circuit is good or capable to handle the 8Kw but the transformer is not big enough to handle that much load. One reason for that is that with no load the inverter gives 110v and with a couple of lamps ( maybe 200w load) the voltage drops to 106v. Some form of restriction the circuit has but overall very good and thanks for uploading the video.
I have been said that for out of 1000w are 12 mosfet, why 24 mosfet then?
@@francerantoniodelarosarami4577 Why do they think people are all stupid....
Hello, why you do not use the diodes D4,D5,D6,D7 used in the egs002 schematic?
IRF Fets IRF44N have a Vdss (Source Drain Voltage) 55 Volts I'd be very hesitant running these fets with a 48 Volt supply rail. (even in a bridge) for a start. AND as a parting shot to the Keyboard Cowboys --CONGRATULATIONS - YOU BUILT IT!. (From an retired engineer who used to design these circuits )
PS. Suggestion for an inexpensive transformer source REBUILD the secondary of an old microwave oven. Should be good for about 1KW .
don't microwave oven transformers have a gapped core as current limiting? would that not present a problem of overheating the windings when used in this manner
@@drspastic Another of the many problematic aspects of this build. At low flux levels would be ok BUT leakage inductance can be problematic. I like the idea but there are MANY DEVILS IN THIS BUILDS DETALES.
At HIGH AMPS 1oz Copper PCB (usually used} Is NOT the ideal construction medium which I see used a lot.
@@cameronbruce1862 What would you recommend to modify this build to make it 60 Hz, 125VAC, & actually provide 8kW of usable power?
@@drspastic Yes BUT the core is a start. The Primary becomes the secondary and that leaves the PRIMARY to wind. Remove the shunts. The core I used was ungapped although it was not (ideally should have been) interleaved. (Welded) This was an Heath Robinson build for me. As I said these builds are full of PROBLEMS for the inexperienced. Even some commercial units are ?
@@ab_ab_c My suggestion is get some CHINESE MODULES. It doesn't make for a "NICE BUILD" but they have sorted all (hopefully) the problems out leaving the POWER STAGE for you to build. I like to use COPPER BUSSES not the PCB. These have also a small heat removal advantage and importantly low stray impedances (Which can result in parasitics) that can cause problems in these ckts. 8KW at 125V 60Hz is not a problem HOWEVER What and HOW LONG DO you need it to handle OVERLOADS when eg. A motor starts up. At 8KW you'd need to get probably a custom transformer which you can always UNDER RUN (Reduced power ) as you add more current capacity to the power handling devices over time/ Remember these are POWER CKTS and if yo can WELD STEEL of an outlet think of what this could do with over ¬6X the power.. It is not pretty when things go catastrophic
Please, upload the pcb and circuit diagram
We learned there are sine wave boards available readymade by this video thanks 8000 watt. 10 hp
Good job sir. What are the changes to the circuit in the case of a 24 and 48v systems?
8kw? are you joking? this can handle 8 Mw!
8μW.
🤣🤣🤣👍👍
I think he means the circuit can not the transformer because the transformer is a 350 watt transformer the more load adding the lower the voltage get because the magnet field is getting weaker he need a bigger transformer with bigger wire to conduct high current making the field much stronger to handle heavy load but am not a fan of heavy transformer core it’s better to use ferrite core and make a two inverter circuit the voltage drop is very little compare to bigger heavy iron core transformer that have a lot of losses in energy
the circuit in pcb like the mosfets are just driver as well as the spwm that generate the pure sine wave. but the real part that generate the high output wattage is the transformer with feedback to stabilize the generated power
so why are you using so many small mosfet instead of using 4 proper big one
Good job
I have a question about pin 5 and 9 I want to use 300 volt mosfet to use a 270volt but pin 5 and 9 is my trouble but they have to connected to mosfet drain and am using high voltage so am asking what is best use a buck converter or resistor
I have a question because I want to build one from old microwave parts. Shouldn’t this have a fuse and what kind? Should there be a fuse for the AC side and DC side. I want to build a whole home solar grid. I would like to do this safely.
Try Making a TIE Grid Inverter, it looks really good
no please do not try to make a grid tie inverter after seeing tech that went into this job
@@drspastic let em do it in their country. Probably no electrical codes to stop them from winning a Darwin Award.
Question why mosfet like irfz44n can’t inverter with 20 volt and the data sheet said 50 Drain to source but anything over 14 volt blow out the mosfet is that mosfet voltage ratio is not in inverting mode but switch mode
80 MW inverter created 🤣🤣
Nice project.
Transformer specification
No knowledge about the transformer you used .
When you test you must use a heater or a motor 4 or 5 KW but you used lamps all of them are less than 500W .
where can i download the plan? the link isnt available , thanks in advanced nice project
Dear friend,
Could you tell me please what kind of black color that you are using?
best wishes
Ciao.il tuo inverter e interessante .ma per realizzArlo devi dire dove posso comprare tutto il materiale anche quella scheda elettronica che tu metti dove si può trovare ci tengo ad una risposta .
Leggi questi codici nella distinta materiali EG8010 IR2110, anche io mi sto documentando per costruire un inverter 48V DC \ 230V AC
Très très intéressant comment avoir cette connaissance ?
Intro music would be fine if a little bit light sir.
from where I download the Circuit diagram?
hello..can u teach me how to change 24v to 120v input inverter and output is 220..mine is use egs board for sinewave
What if you want 60hz? You ran it at 110v 50hz? It's 60hz no?
Depending on where you live in the world it varies from 50hz to 60hz. That's why European plugs are different than American.
On the EGS002 Board there is a jumper you can short to get 60Hz.
hello will the same scheme happen with IRF 3205? Or will it need correction?
Avez vous un site web pour le travail ?
Could you assist with an 800w inverter circuit we are working to provide them to places where they still have scarcity of power for days
La tarjeta driver esta perfecta... Pero el dimencionado de los cables del transformador a la tarjeta es muy pobre... Y eso hace que pierda potencia (de 110 se baja a 104 voltios) le recomiendo hacer la tarjeta de potencia por separado
Awesome video sir
The links are down, the shematics
Very interesting please the circuit diagram
I tested the low frequency inverter that I designed but the out put is giving me 106v and when I connect filter capacitor of 5uf the out put dropped to 83v without feedback and when I connect the feedback the out put go up to 85v and the the feedback voltage is 2v minimum. What could be the issue while the out put can't go up to 200v. I used spwm module.
Thanks for your reply
Bhai background music ko. Change krr do ham bor ho gyi sunte sunte
Where did you get the transformer?
Where do I get the 17 pin socket?
There are some concerning things here. The mosfets should be electrically insulated from their heat sinks. When you follow the link back to where it is claimed the circuit diagram is, you find only the pcb pattern and an image of a purported “free energy device” (nonsense). TechBuilder has a better design and tutorial, with better safety practices.
Plastic heat sink. Obviously ....🙄
Check Full Load performance try 🙏🙏
I don't where to order this pcb lay out.
Ciao.sarei interessato a questo tipo di inverter.per favore puoi dirmi dove posso comprare tutti i componenti per poterlo realizzare compreso il circuito stampato.spero che mi dai una risposta grazie
Can you build stable working versions on request?
Drive heavy loads ,like AC ,iron, refrigerator.
Dear what is the MOSFET no kindly tell me
Where are the DC input capacitors? Without them, your inverter will not have much of an inductive surge capacity.
kindly share link for pcb and circuit your share link not working
Sir which site is best for buying online electronic component
Sir please give me answer
Maybe 800 watt 😌
How much of one board
what transformer did you use there??
Great. Pl share the circuit diagram
PCB diagram
Make on grid solar inverter video
how to order buy your power sine wave?
Hi
PCB Layout link is not working ?
Please make a very powerful 100 watt stereo audio amplifier 🙏🏽🙏🏽🙏🏾🙏🏾🙏🏿🙏🏿🙏🙏🙏🏽🙏🏽🙏🏾🙏🏾🙏🏿🙏🏿🙏🙏
From where are you?
Per avere il pcb cosa si deve fare?
If I want to support you then a problem is no Paytm no paypal no any other way then how can I pay you in inr
ESE TAMAÑO DE TRANSFORMADOR JAMAS DARA 8000W COMO MUCHO 3000W
Hi could you send a parts list and a circuit diagram plesae and thank you!
تیار سرکٹ سیل بھی کرتے ہیں
ट्वेल बोल्ट इं इन्व्हर्टर हाऊ मच प्राईज इंडिया
Don't like
Você conseguiu comprar um?
Plz help me..... l'm sithija.
is your circuit 230v s....? Do you have PCB board for sale ? Or can i have gerber file please.
Is it possible to make a 21Mhz pure sine wave circuit?
please don't give him more stupid ideas. there's enough interference on 15mm band already.
Please share circuit diagram Sir
I transistor che sigla anno
ขอวงจรอินเวอร์เตอร์เพียวชายเวฟแบบง่ายฯใช้ได้จริงด้วยครัผม
Circuit diagram?
One piece delivery hobe
Podłącz pod tą przetwornice przynajmniej 2 żelazka :) i to będzie prawdziwy test
Nie podłączy. Bo jest oszustem. Nie wierzę że te tranzystory wytrzymają 666A.
Test will be some milliseconds long. 🤣
Trn facet jest Click Bait kretin. 😉
(Moj polski jest kiebsko...)
Pozdrowienia z Niemiec
@@Stefan_Dahn pozdro ;)
Podria obtener,de alguna empresa, la pcb hecha sin tener que mandar los archivos Gerber
220v system please
Please can i get the circuit diagram?
Amigo eu tenho o layout, você teria o esquema eletrônico desse projeto
Compliqué pour pratiquer
While the concept and design is practical, the cable size and the transformer are impossible to support 8kW, it is make sense for the system displayed to support 4kW for 48V system but 8kW is way off.
Yo vi mucha gente asi .
Muchas preguntas y ni una respuesta .solo quiere seguidores . Mi pregunta es cual es la entrada y la salida del transformador y como puedo tener el diagrama para acer una .con la respuesta yo creo .gracias
8 kw. ? 8000 / 110 = 72,72 amp.When you remove a rabbit from that transformer, 72 amps will also come out. 48 v from the input of the transformer. 166 a. You are entering... I hope your teacher has not seen this video. He would say he was wrong about electronics and commit suicide.
el circuito se puede modificarle la frecuencia de 50 a 60 hz??
hello 👍
Sei bravo a presentare il video ma quasi tutti non siete chiari nel spiegare i particolari .ad esempio dove posso prendere lapiastra circuito.laltra schda piccola cosa e.poi alla fine metti unaltro inverter o cosa il tutto non è chiaro.
El Diagrama para poder comprender mejor amigo
Where is scheme ? -
I wont this diargrame
not american tech but india tech
friend please friend I wanted to assemble this project, you send me the project schema
I'm a Brazilian
use a language translator
i learned from the TH-cam how to convert DC to AC for the first time using a tranformer with 2 NPN transistor its worked I plugged a 240volts glob the lights come on buts it’s flicking I wonder why i worked it’s out something to do with a resistors its wasn’t right I using the ohms laws put its together to get the right one it’s worked it’s never flicking a gain i things why didn’t the TH-cam explains its how to worked its out to get the correct resistor maybe they things it’s may cause Brian’s damage the nexth my invention is how to make its powers to drive a 2000 watts heaters
Did they pre tin? 🤣
Great. Pl share the circuit diagram & PCB diagram
le schema du montage
50 Hz,low freq???? **DON'T DO IT** the efficiency is terrible,you will regret it
you need a hi freq inverter (20Khz,30 Khz...)
been there checked that
Minta 1 bohlam
LIKE NEGATIVO POR TENER DEMASIADA PUBLICIDAD 👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎
Amazing !
Yes, truly magnificent, the colors, all these little black things contrasting with the green, and the beautiful music. What I didn't understand is..... what the fuck is it for?!!!
un autre osti de video de crosseur de tabarnack ....made in indouuuuu
Max 1kw
Please help.. We need your help. I dont know how to do that and i dont have any idea about like this video, but my brother's and friends said that can you make a per video step by step tutorial building a 48v 10,watts if you can or let say 8,000 watts so that we can make or follow step by step your video and so that we can make a high capacity inverter to run stable our house.
Please and we will help you and your channel to promote here in the Philippines for more subscribers, likes and comments.
If you can, please make it sure step by step especially what devices or materials to buy so that we complete all even the wire and etc cause we dont have any idea, we creating base on your video. Hopefully you can help our request cause if we buy a inverter is so expensive.
So that we can run our
1 Inverter type of refrigerator
1 Inverter type of Freezer
1 65 Inches Samsung Smart TV
1 amplifier and sound system with 2 big box of speaker and 6 small speaker
4 electric fan
5 ceiling fan
5 pcs 20watts led bulb
3 pcs 15 watts led bulb
5 pcs 9 watts led bulb
1 of 1.5hp water pump or induction motor
Please make this as our request..
Step by step so that we can understand.
Please input all the devices or materials.
Thanks and god bless you sir/maam
I hope you can make this within this week. We are so excited.
Please email me at pimentelarvin@gmail.com or mention me so that we know that your done creating and uploading our request.
Once again. Thank you 🥰💪👏
Schematic
Without blue print this video has no value.
👍