At 7:45, how has the Isopon body filler repair held up? The right side of my Honda HRX217 mower deck has worn through from years of grass and debris circulating under the mower deck, and I have been thinking about trying this kind of car body repair. I am the original owner, but the Honda "lifetime warranty" for the NeXite mower deck only applies to defects of materials or workmanship. When I purchased the mower, I mistakenly thought it covered any failure of the mower deck.
Hello how did you unscrew the central screw of the clutch? because I try but when I unscrew the engine runs as if it were in compression. Thanks in advance.
What is the gap on the throttle/choke cable @18.43? I am having problems getting mine running, it was only running for 3 secs after pull, i cleaned carb/ALL jets, new fuel, new plug and now it will only run with choke on full, will not run on rabbit/turtle?? I have tried the idle screw at 1/2 turn to 4 full turns out and still the same?? HELP!!!!
Maybe you have some problems with that spring from under deck,check there for rust or that big washer is dropped, or press hard on the deck and pull the Lever.
Alex, I have a Honda HRB475 that that the gearbox pulley has failed, I’ve replaced the pulley but the tension spring ( the small spring) is missing, where does it attach to and from , I can’t find any diagram showing this and sadly your video did not show the outer side of the gearbox when you removed it.
Congratulations on the video! To adjust the valve clearance (0.15mm intake and 0.20mm exhaust) how do you find the top dead center in the flywheel? or do you use another method? Thank you
Bonjour elle est très très bien ta vidéo elle est vraiment impeccable je regarde tous les vidéos par contre tu n'explique rien et tu vas beaucoup trop vite sur ta vidéo
Great work! Cheers from italy
Been doing something very similar these past few weeks!
WOW, Nice work and smart to buy that 2nd engine for parts. 👏👏👏
Nice work
At 7:45, how has the Isopon body filler repair held up? The right side of my Honda HRX217 mower deck has worn through from years of grass and debris circulating under the mower deck, and I have been thinking about trying this kind of car body repair. I am the original owner, but the Honda "lifetime warranty" for the NeXite mower deck only applies to defects of materials or workmanship. When I purchased the mower, I mistakenly thought it covered any failure of the mower deck.
Today i repariert the Self Honda Motor from 2001. Now the Engine work😉 greetings from Germany 🤟🏻
clever bloke. very satisfying 👍
How did you fix the height adjustment please? I can’t get mine to cut higher than 5…
You cleaned the main jet, but not the emulsion tube on the video. That may have caused some slight surging.
Очень хорошо! 👍 понравилось!!
How did you fix the height adjustment please I seem to have same problem but it wasn't in the video 😂
You did a very good jos with this mower
Great job..nice Honda.
Hello how did you unscrew the central screw of the clutch? because I try but when I unscrew the engine runs as if it were in compression. Thanks in advance.
What is the gap on the throttle/choke cable @18.43?
I am having problems getting mine running, it was only running for 3 secs after pull, i cleaned carb/ALL jets, new fuel, new plug and now it will only run with choke on full, will not run on rabbit/turtle?? I have tried the idle screw at 1/2 turn to 4 full turns out and still the same??
HELP!!!!
i think the gap is 0.80 -1 mm.
How do you lock the engine to remove the clutch plate bolt?
How did you fix the deck height adjuster? I have same problem on roller deck version.. pull lever and nothing
Maybe you have some problems with that spring from under deck,check there for rust or that big washer is dropped, or press hard on the deck and pull the Lever.
Alex, I have a Honda HRB475 that that the gearbox pulley has failed, I’ve replaced the pulley but the tension spring ( the small spring) is missing, where does it attach to and from , I can’t find any diagram showing this and sadly your video did not show the outer side of the gearbox when you removed it.
19:45 Thats still running rough dude!
Гарна робота! Привіт з України/good job! Hi from Ukraine
Congratulations on the video!
To adjust the valve clearance (0.15mm intake and 0.20mm exhaust) how do you find the top dead center in the flywheel? or do you use another method? Thank you
Bravooo!
Bonjour elle est très très bien ta vidéo elle est vraiment impeccable je regarde tous les vidéos par contre tu n'explique rien et tu vas beaucoup trop vite sur ta vidéo
Bravo
For April fools next year you should make a video like those fake restoration channels. With the reversed footage.