How To Fit Electrical Pick Ups To Kit Built Locomotives

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 21

  • @Nivshin53
    @Nivshin53 5 ปีที่แล้ว +2

    Although I have done this for years, I am really enjoying your whole series which provides a sound basis for anyone wanting to start - and lots of tips for those of us who are more experienced. Although the "Godfather" Tony Wright set me off on kit building 20 plus years ago, I also found that being a member of an MRC put me in touch with others with far more engineering skill than me. but also with lots of tips that I have picked up on. One of them was to switch from .45 NS Wire to flat Copper strip for the pick up and where I have found far more stability - in other words, once a Loco has been running, the strip always stays in place whereas the wire does have a tendency to be moved out of place by the Loco's movements (especially on bends). My solution for the problem with the brake gear is to lop 'em off on the smaller engines that are tight on space - its not the thing to do of course, but nobody ever notices in operation!!! Keep up the good work - Dave

    • @BrentSudric
      @BrentSudric 3 ปีที่แล้ว

      If I may ask, how do you replace the wire with flat copper strip?
      I mean, is it similar to the way this person did it or does it require modifications?
      I’m thinking of kit building and I’m asking for tips on it. (J72 chassis for GER C72 )

  • @mike_edwards_squarcles
    @mike_edwards_squarcles 7 ปีที่แล้ว +1

    Thanks for covering the subject of pick-ups. great explanation and demonstration. Very impressed, not only by the standard of modelling, but also how you manage to do it all with the added pressure of that filming and commenting.

    • @cb01ttr
      @cb01ttr  7 ปีที่แล้ว

      Thank you Mike, very kind of you to say. I have to admit, it isn't always done in one take... the wonders of digital filming! ;)

  • @johnjephcote7636
    @johnjephcote7636 4 ปีที่แล้ว +1

    Buy glass fibre-backed copper clad. It resists soldering heat better. The thin paxolin stuff as used for sleepers does not stand re-soldering and the copper peels away.

  • @Indokita
    @Indokita 4 ปีที่แล้ว

    Nice helpful video.
    On this video you only install 1 side pick up. For DCC, it should be both sided pick up, is it correct?

    • @cb01ttr
      @cb01ttr  4 ปีที่แล้ว +1

      It's generally considered recommended practise to install pick-ups both sides for DCC, but it isn't essential, providing the decoder is completely electrically isolated.

    • @Indokita
      @Indokita 4 ปีที่แล้ว

      @@cb01ttr Ok thank you.

  • @jagc1969
    @jagc1969 5 ปีที่แล้ว +1

    Great video and great ideas ! Thanks for sharing.

  • @Trublemaker12
    @Trublemaker12 4 ปีที่แล้ว +1

    I plan on doing this to a Westside Brass FEF-3

  • @ericmalleval
    @ericmalleval 6 ปีที่แล้ว

    Hello, are we lucky to see the fitting of the embellishments on the 4-6-2 DJH model? I have doubts for my kit :)

    • @cb01ttr
      @cb01ttr  6 ปีที่แล้ว

      Hello Eric, yes I will be completing the model at some point, though I haven't been building much of late.

  • @petergarrett9185
    @petergarrett9185 7 ปีที่แล้ว

    Just a suggestion, when soldering wire don't use an acid flux, I use a paste flux on mine, doesn't turn green if not washed off.

    • @cb01ttr
      @cb01ttr  7 ปีที่แล้ว

      Hi Peter, thanks, I've not yet tried paste flux, might give it a go in the future. :)

    • @Nivshin53
      @Nivshin53 5 ปีที่แล้ว

      I do the same as well - avoids any corrosion on the pick-ups later on.

  • @DodgerB763
    @DodgerB763 7 ปีที่แล้ว

    Nice top!

    • @cb01ttr
      @cb01ttr  7 ปีที่แล้ว

      Cheers mate, it's new...

  • @farmerdave7965
    @farmerdave7965 6 ปีที่แล้ว

    Use 60/40 solder and always use rosin flux. Never use acid plumbing flux.

    • @cb01ttr
      @cb01ttr  6 ปีที่แล้ว +1

      I'm not using acid plumbing flux... I presume you mean that your personal preference is 60/40 solder and rosin flux? As always in model building there are many ways to achieve the goal.

    • @farmerdave7965
      @farmerdave7965 6 ปีที่แล้ว

      When soldering electrical connections, rosin flux is always used, unless you want your connections to corrode. If you use silver bearing solder, too much heat will be required.

    • @cb01ttr
      @cb01ttr  6 ปีที่แล้ว +1

      Ok, thanks Dave.