Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
@@christhayil8354I miss mine too. But I’d be the one doing stuff instead of the other way around. He came back from the army quite messed up. But…I can do most anything on my own at least, since I never had any help. I do wish I had someone to call on tho to do things like this every now and then. I just replaced a ballast and dang near broke my neck.
There is always one major problem with flushing/draining a water heater and that is the acutal drain valve used for above purpose. They are typically a hose bib type of valve and these all have a small orifice (about size of your pinky finder nail), This makes it very, very difficult to flush or especially drain the unit. This is especially true for older units that have a lot of built up sediment. As a retired GC whenever a new water was installed I had the plumber replace hose bib type drain valve with a 'full port ball valve' which provides a full 3/4" diameter opening for flushing/draining. Every 6 months I flush into blue 5 gal bucket a couple of times and thats it. If you wait a few minutes for sediment to settle in bucket you can see how much sediementf is removed.
You convinced me to do it myself on my 2-year-old Rheem 50 gallon unit. It came with a plastic handle that was so simple to turn after connecting my garden hose. It was a full 3/4" opening. I did the power flush and crimped the garden hose a couple of times throughout the 15-20 minute process. Easy and remembered to write down the date in my owner's manual attached next to the water heater. Thanks for a great video!
Gray presentation. I had to do a flush for a client a few years ago and it was bad. I went to do a gravity flush, relieved the pressure in the system but nothing would come out of the drain. I was afraid the drain itself was broken. So I took a length of copper wire from some scrap Romex and fished it into the drain and it was completely clogged with sediment. We have a ton of limestone here. I managed to free up enough to slowly drain the tank. Once it was drained I removed the heater elements and they were covered in sediment stuck a flashlight inside and I could see about 1½ inches of sediment so I stuck a shop vac hose in a sucked out out. The tank was still in great shape so I replaced the valve and the elements and it's been working great since.
This year marks the 30th year (thirtieth) year of my hot water heater cranking out hot water and it was installed when we moved in. It may be 40 years old. She rocks super hot water everyday. Thanks so much for this video.
I moved into my house in 2014 and it had 2 identical (one gas, one electric) 50 gallon Ruud hot water tanks still working originally installed in 1988. I changed them both because I didn't want to chance it and the home insp. recommended it. The electric one is for the bathrooms and the gas is for everything else (kitchen, laundry, bars, garage, utility). I bought a gas Rheem Platinum 12 year with 2 anodes and an HTP lifetime stainless 5500w elec. But those Ruuds that where in there I doubt, in fact I'm pretty certain they never had the anodes changed. I think the dates on the tanks were 1987. They did have a decommissioned water softener (which I replaced) but I don't know how long they were on the softener. They weren't really heavy like they were all crusted up. I hauled both of them out of my basement myself after I drained them.
Hola! 🖐 Excellent video, very useful information. I replaced my water heater about 6 - 7 years ago. The old one WAS SO HEAVY due to all the sediment that had settled, I had moved in shortly before the water heater went out. I now make sure to drain this one every six months, we have some really - extra "hard" water where I live (Southern California). I hope that a lot of people see this video and put this on their calendar just like changing batteries in smoke detectors, replacing filters in the refrigerator, etc. Take care and have a good one, Adios! 👊
This often forgotten procedure not only preserves the heater, but insures your energy costs, gas or electric, go toward making hot water and not toward making rocks. Thanks, Ethan!
Thank you so much Brent, Eco Plumbers, and The Honest Carpenter! My husband and I have to do this for our water heater. We are both newbies at this, so this tutorial is so appreciated!!!
Thank you, thank you, thank you. This was the easiest method I've seen by far. I love how you explained at the end to keep the hot water valves open while you're refiling the tank to get the air out of the system. So many other videos either skip that step or want you to mess around with the air pressure valve, which I am afraid to do as I heard too many horror stories about that.
Excellent explanation. I did a combination of both methods, gravity and cold water pressure. Back and forth also manipulating the drain hose to see if any sediment would break free. As other have suggested, if I run into problems with sediment and have to do another flush I will replace the drain valve with a larger size like 3/4 ball. Ours is 75 gallon so I'd like to extend its life as much as possible before replacing.
I always power flush into a white 5 gallon paint bucket, watching the sediment, emptying it, repeating until I stop getting sediment. If you prefer, one can hold the discharge end of the hose and feel the outflowing stream; you will feel the particles hitting your fingers.
Yes you need to and don't turn back on until you have refilled with water. Very important make sure you have got all of the air out . If one of the elements doesn't have water around it. When the electric is on, it will burn the element up. @ukram350
@@ukram350 You really don't have to since you are always going to have water in the tank when you power flush. If you do the gravity method then yes, since you'll be emptying your tank and your elements would be left with no water and possibly burning them out.
During flushing process, pulse the cold water supply off and on several times to disrupt and wash out more sediment. If partially or fully draining tank, it would be a good time to extract and check the anode rod. I've also heard that using a garden hose (attached to cold water supply, obviously) with a spray nozzle to spray down into the top of the emptied tank while the anode rod is out can help flush out the sediment. I've had problems with using garden hose to drain because it gets clogged with sediment -- especially a very long hose to take the water out of a walk-out basement. I may look for a way to transition from garden hose thread to a discharge hose (like blue pool discharge hose}.
I use method one. Just FYI on one point. I save the flushed water in a garbage can and use it later for plants. One more question - what are the pros and cons of each method? Thx for an excellent video.
@@mitchelcline9759 I checked with my local Sierra Club guys who wholeheartedly endorsed my actions. The contents are mostly calcium salts and the impact on the soil is beneficial. Here in the San Diego area water is critical and I hate to waste water by draining my contents into the street drains.
@@kersi-sandiego6036 i haven't looked into it. I figured the city water part would be fine. I was wondering more about what types of things are produced from electrolysis between the water and electrodes? I've no idea how much or what all gets made from that and no idea what it would do to plants. To be safe i would personally not eat and plants from that method but i also don't know much about it just wondering
@@mitchelcline9759 Whatever works for you. However, I almost guarantee you that the water used at commercial farms and nurseries has far more virulent stuff than what's in the water heater. Anyway you have to do what's right for you. Thanks for your input.
Thank you for this video! I just bought a house and found out that this was something you need to do this. Thanks for sharing now I feel confident to do it on my own!
The biggest cause of heater failure is expansions and contractions from setting the temp too hot. Cracks form in the protective coating and rust rapidly destroys the tank. My 1989 heater, in hard water CA, works as good as new because I keep the temp low enough to not need much cold water to mix. Also, I never replaced the original anode rod. I flush it, with water supply on, every 2 to 3 years. I replaced the small plastic drain valve with a 3/4" ball valve. I replaced the original inlet tube about 3 years ago. If the tube breaks you'll get a very short amount of hot water because the incoming cold water quickly mixes with the upper hot water. Never drain the tank because incoming oxygen will quickly corrode weak spots.
For the gravity drain, another video showed a good idea I think. After the tank is empty, open the inlet valve for 10-20 seconds to agitate the sediment and then drain it into a bucket. Repeat until the water in the bucket appears clear.
I installed my water heater in January 2019 and flushed it today for the first time! (yeah, I know I should've been doing it!). When I just drained the tank, there was very little sediment in it. But then I started a flushing process - Run the water for a few minutes . . . then tuen the cold water on for maybe a minute and then let it drain our. You wouldn't believe how much settlement came out that time! I've been repeated that flushing process maybe eight or 10 times and I probably got a full cup or a cup and a half of just sediment out! So, in my case, the initial draining did almost nothing but cycling several flashings really did clean the crap out of the bottom!
I installed 3/4" full port ball valves on the drains of my water heaters, for a much more vigorous flush. Some of the drain valves that come with the tanks have a very small opening, where any sediment larger than about 1/4" will clog it and stop the flow. In my area, once a year flush seems to be plenty. Anode rods here last about 5 years before it is best to replace them -- I doubt that 5% of owners ever replace an anode rod.
From NZ.... this was something I hadn't thought of.....maybe it's time I did as we have been in this 2 b.room unit for 20 months now. Inconveniently, the electric hotwater cylinder130 litres capacity is in the upstairs roof cavity so there's a challenge. Sooner or later more worryingly it will need replacing...I worry about Cost but also how on Earth the nice plumbing men are going to get it down through the manhole which almost exactly fits the diameter.🇳🇿🌝
Just clean a Electronic tank, I take out all the heat core, and you will find the lower hear core hole is big enough for a 1/4 pvc pipe, first put some acid into the tank, wait 15 minutes, I connected a curved pvc pipe to shop vac and start to vacuum all the stuff on the bottom, it's pretty efficient and works well. It's a 2006 tank and after clean out and change the rod & heat core, it works perfect now! Cost: Rod $30 + 2 heat core $34 ........
Best to remove bathroom tap aerator screen before flushing. Scale and sediment will be broken loose and clog screen after refilling tank .Don’t use kitchen tap to vent, refill as they are more difficult to service.
You say a properly maintained water heater can last up to 12 years. I installed mine in 2006. I read on a Ridgid plumbers forum years ago that you should drain a couple o quarts of water once a month to get rid of any sediment. I have done that since it was new and the way I did it on mine was this. My water heater is in the garage next to the outside wall and on an 18 inch stand. A pipe from the pop off valve near the top of the water heater runs down the length off the water and out the wall where it would drain onto the sidewalk if needed. I cut a tee into this pipe below the level of the drain valve and then ran a section of permanently mounted hose from the drain valve to the tee and I also installed a ball valve at the tee to isolate this hose from the pipe. Once a month I go out to the garage and open the drain valve and guesstimate when I have drained a couple of quarts of water and then close the valve. Been doing this for 17 years and it works very well and is very easy to do as all I have to do once a month is open the drain valve for a few seconds.
Thank you so much for this video! The anode prevents corrosion of Fe--it would not prevent build up of CaCO3 & MgCO3 & other salt deposits. A water softener inlet line would prevent deposits from hard water, but as the Mg anodes corrodes, it would be the source of deposits! The Corro-Protec Powered Anode is conceivably the best route but are X 3 more expensive and consume electricity but claim to last for 20 years! And so a combo of water softener and the latter is the best route but is expensive.
When I was living in LA Ca. area I tried to flush my gas water tank 50 gal, because of some video. I even change the discharge to a bigger orifice valve. So I collected almost all of the water and put them in 35 gal drum and use the water for watering the plant while it discharge. I found out that I wasted my time since I didn't find any sediment accumulated, almost all the water are clear since my wife trying to save water. So now I don't flush any water heater, since my first house lasted about 15 years before it leak, on my second house 75 gal tank lasted about 17 years then it started leaking. So I just ignore the maintenance, since the sign of need replacement is when it start to leak.
We had a water heater that made noises from sediment and it lasted 25 years with no maintenance ever done, and we had the hardest water you can imagine!
Given that the tank lasted for 25 years even with all that sediment, but consider how much your energy costs were increased as your heat source had to work harder to get through that sediment to heat the actual water!
For heavy sediment, replace original drain valve with a 3/4" ball valve. Use an old plumber's snake preferably about 2-3 feet long. Open new ball valve, insert snake and then watch all the chunks flow out with ease.
That was so clearly explained...like all your stuff! Thank you. We have not yet flushed our water heater and since we're on well water I expect lots of gritty sediment.
Thank you very much for this good video and advice. I just got done and all went well. The only problem I had was getting the old anode out to replace it. Once i got the threads to break loose, thought all was good but couldn't pull the remaining rod out. A 10 inch section of it had turned perpendicular to the hole.
Wow, I have that exact same gas water heater used for the power flush! That looked really simple. My back door is inches away so I will just run the hose outside into the backyard.
Appreciate the post. However... (here it comes) you didn't pull the annode and check condition. (Amazon has flex replacement annodes for under $30 bucks.) Have rental properties and this step is a MUST DO for tank longivity. Amazing how fast these will corrode away to nothing and then the tank rusts/leaks. (I swear, the makers of these tanks are counting on this.) Down side to this extra step is the first time you pull the annode you'll need a 1/2 inch impact. On super tight from the factory. Breaker bar w/ pipe extension won't work because the tank will want to turn with the rotational force needed to break the annode free. No way to hold it in place to apply force.
@@stevenallen1392 thank you so much. I flushed out the hot water tank for 30 minutea. Ran my hot water faucet in rhe bathroom for 10 minutes. Everything is normal now. My water was a rusty yellow color. Tank is only 7 yrs old. Hopefully i dont have anymore issues.
@@scottvan1898 I remember seeing an episode of This Old House where they showed one that was sectioned (like a sausage) so it could be bent and fit in a tight space.
I change mine every 2 years,My glass lined "Self Cleaning" 50 gallon gas tank is now on year 20 ,total pain tipping it off the stupid platform but its necessary, Vegas water too.
I actually use a combination of both methods. I start by draining the tank first. I then use the flush method second. The drain method in itself still leaves debris in the bottom of the tank. I’m guessing you would only need to use the flush method and eliminate the drain method. Good video thanks for sharing.
The 1st of every month, I turn on the drain valve wide open for one minute. I keep a small section of hose connected to the tank all the time and the other end in the drain.
My water heaters outside in a closet,,, instead of wasting the water down the drain I'd water my bushes and trees with the flush water and did it often this way I wasn't wasting it going down the street or the drain (its an Arizona thing ) but before I invented that ,,i would flush it onto a used furnace filter this way I can see what's coming out and how much and when it stops coming out, this way I can monitor it
Thanks for your work on this video. Brent presented these methods straightforward and understandable to all. I have to drain one at my father in laws house. It makes a gurgling sound and found your info. here. I didn't know about the pressure method by using the water supply to flush the tank. My drain access is slightly higher than the valve on the tank so it should work well.
Holy Crap!?! Who Knew?!? Thank you! I had anew heater installed one year ago and I needed to do this. I was not aware of the first method -I will use it. Another terrific presentation.Cheers!
I live in an area with a lot of calcium. It has been my experience that most here get about 18-20 years out of a hot water heater at which point it's time to replace due to the sediment. As a former appliance repairman who also worked on water heaters, two things became apparent. First opening the drain on a water heater, especially an old one is a crap shoot. Some WILL develop leaks. A cap may fix it. Secondly, as a couple of others on here have noted, back flushing does very little to remove the sludge in the bottom of water heaters. There is just no good way to do it with the little hole you have to work with. (This is obviously by design of the mfg.) You'll get some, as evidenced at the end of your hose, but not much. Good luck.
I'm 75 and NEVER heard about flushing a water heater until just last year. It is something I am NOT able to do by myself but I have mine flushed twice a year by the company that does the annual maintenance for my A/C and furnace. I live where the water is extremely hard and wish I had known about doing this 20 years ago. My water heater is soon to be replaced since I have it on the highest setting so that I have hot water.
Hi Ethan: I want to first say how much I enjoy your TH-cam channel and your blog. I am a very new user of power tools with DIY projects -- your videos have been amazing to watch and I have learned much from them. I have tried to find classes in this area, but they seem to be sparse. Have you ever considered offering in-person classes -- they could focus on the proper, safe use of certain power tools (your video on the proper use of a circular saw is great), be project oriented or focus on a specific DIY topic. You are am amazing teacher and I think you'd do very well by offering classes in this area.
I didn't realize it was this easy. I made a contraption with a Y valve switch that shot air from my compressor into the drain valve to stir up the sediment. I probably didn't need it. It was pretty messy. I'm going to see if I can replace the sacrificial anode next.
Great video. Nearly everyone I talk to doesn't ever read their manual. That would inform them that they need to do the flushing periodically. The "Master Plumber" said the heater came from his company. That would indicate that they did the install. I noticed the connections were created directly from steel to copper at the water in/out pipes. You really don't want to do that. You need 6" of brass between the 2 metals to prevent electrolysis...That's the way I was taught anyway...
Thanks for the informative video. I attach a small mesh sock or nylon netting on the end of the hose to see if any sediment is present in the tank. Thanks again
Last 12 years? When I bought my house in 1998 it had a gas water heater that was installed in 1978, I seem to remember it was AO Smith, it served me perfectly fine for about 15 years, it started to have a small leak around the drain valve inlet I guess where it was welded on, so I replaced it, after I took the tank out I cut it open, the inside of the tank was a nice clean grey no corrosion, but about a foot solid chunk of mineral buildup on the bottom, which was why I was never able to drain/flush it- the previous owners obviously didnt, but that water heater still lasted about 36 years!
This was interesting and easy to understand, thanks! I'm having it professionally, but it's always good to know what they're going to be doing and how they're going to be doing it. Also, what kind of screwdriver did the plumber have that holds interchangeable bits in the handle? I have to get me one of those!
Great video!!! I always thought that you HAD to turn off the supply. I've had my water heater for three years with no flush, recently moved into home and didn't feel comfortable messing with the old gate valve. My luck that the valve will be older than Methuselah and will start leaking if I start screwing around with it . Eventually I'll have it swapped out for a ball valve. I wanted to put my burner on pilot, connect my hose and like the video slowly flush the water heater until I get clear water.
In talking to a Plumber of 40 years he told me flushing is a waste of time. Basically you don't remove much from doing it you just channel the debris then it settles back. I have owned two water heaters, 1st lasted 15 years and second 12 years and neither was flushed. Only thing I do is make sure sufficient make up air for clean burning. Cheers
When doing the gravity drain method would it not be better to allow the first minute of flow when the pressure is turned back on to flow out the hose to prevent any residue of sediment to flow out the drain rather than into the system so as to not clog things at faucets?
Thanks for the video, i just power flushed my water heater yesterday, I'm also interested in these electrical anode rods that dont get eaten away like the typical aluminum and magnesium rods
Thanks. I have question. While refilling the water tank, you will leave open the faucet for the hot ? So when are you going to to turn off the faucet if the water heater tank is full? How do you know if the tank is full. Thanks so much for your response
thank you so much. I always thought running water was better than draining it with gravity. was able to get rid of sediment in minutes rather than hours.
Great video and perfect timing! I have a Bradford White installed in 2005. *Some folks say not to flush the water heater if it hasn’t been done annually, is there any truth to this? I’ve owned the house for a little over a year, so no idea if the WH was flushed on a regular basis.
I've practiced this method with the following suggestion, run the hose to a 5 gal bucket to actually see what is being flushed out. Sediment from the water and from the anodes dissolving can be quite nasty. Also, I've changed the anode rods to extend water heater life but have since converted to an electronic cathodic protection.
Bought a water heater over 10 years and it is an electric type. Difference between it and the newer ones is the clean out hole. This makes the removal of the sediment almost 98 percent. Do to being able to reach inside and actually scoop it out.
If the tank has a lot of sediment and nothing comes out of the drain valve, I've hooked up an air hose to the hot side and a hose to the cold side and blow the water out that way. Doesn't always work but most of the time it does.
Power flush is definitely better since thermal shock to the tank will be less. If you plan to do the drain method, you should turn off gas/electric and let it cool down for a few hours first. If you drain while water is still hot, you run risk of cracking the tank when only air is available for it to exchange heat with.
Thanks for the tip. I did turn the tank off first, but I did not wait more than 15 minutes to drain it. Fortunately I live in Florida so the ambient air temperature is not quite as different as it could be up north in the winter in someone's basement or attic.
I installed a water softener in my home and never looked back . Everything with washing clothes and showering and using tap water is so much more cleaner because of less corrosion on tank and also saves $$$. On soap. My tank is is 10 years old and so far pretty clean of sediment.
@@blindsquirrel7802 Do you turn off both the COLD water inflow and set the temperature setting to VACATION to empty the tank before turning back on the COLD water inflow to agitate the sediment and let it drain?
Good to know. As you flush- does the sediment settle that quickly? I'd of thought flush, wait a minute or more, flush again- but its just a few seconds.
A few questions. For the gravity flush method, he didn’t open the relief valve at the tank. Isn’t this necessary? After the flush, he said to make sure no air is left in the pipes into the house. How do you ensure this - just by seeing a constant flow of water at the faucet? What happens if air is still in the pipes at the faucet?
often have had good results from reverse flushing from the hot outlet. Easy to do. I turn off cold supply, empty tank, leave drain open, and then cap off any threaded single spout in the house and turn on that hot and cold together, causing cold water to flow in reverse to the tank hot outlet, and flushing down the walls and floor of the tank.
I might have missed it but how long would you do the power flush method? Does the timing depend on amount of sediment in the tank? I'm getting ready to tackle this task soon and I know there is sediment in the tank. I really enjoyed seeing the two methods.
I just did mine after this video and I let it run until the water was clear (at first it was a tiny bit foggy, but you can't really see sediment build up like that). If you pinch your hose every few minutes you can often times feel the sediment smacking in the hose where you pinch it, I just power flushed until I could no longer feel the buildup in my hose when pinching. If you attach a thigh high sock to the end of the hose with some rubber bands or a clamping mechanism, the water will continue to flush but the sediment will be caught in the thigh high sock. After a few minutes you can check the sock to see how much sediment has been caught. Another video said if there's more than a few inches of sediment, you have heavy build up and might need to do more. Another method is to drain into a bucket, that way you'll see the buildup as it collects (if it's bad). I'm no pro myself, so I'd just say trial and error, you can always do another power flush if needed or if you are hearing popping etc in your tank. I drained mine for 15 minutes personally, the first 5 minutes I actually could see sediment shooting out of the exit end of the hose because I hadn't flushed my tank in over a year and have very hard water. Hopefully that helps you if no one else has replied anywhere else.
@@TheHonestCarpenter yeah I was also a Bradford white hot water dealer and I had to get out of it due to factory mistakes and way to many came back leaking and of course Bradford white doesn't want you to ship the bad tanks back due to cost but they do pay awesome for the the promotion of their products though
@@TheHonestCarpenter and best way I have found out of all the tanks out there regardless of brand,is to convert it to bottom feed and it's easier than what people think
Thank you you me feel better about doing my hot water tank now I think I can do it. My wife and I moved here 5 years now and the tank is electric so I do need to do soon .
Full port ball valve is good. The best is to drain and clean water heater is to drain just below the outlet and remove bib or element. Get a wet/dry shop vac and use a 3/4" OD hose connected to shop vac and suck out the sediment. You may need to use a stiff fishline to breakup sediment. Move sediment away from around the sides into the middle for easy sediment removal with the hose. Alway fill up tank to just below the outlet before vacuuming sediment again. You need water to mix with sediment to remove. Repeat this until sediment is gone, usually 6 times. I am going on 16 years with a 6 year water heater for my personal heater (electric). It is clean and working well. I clean it every 2 years and takes me 45 minutes to do. Where I live, we do have low calcium, sodium and limes. I am a plumbing contractor and have done this for customers for decades. You can make you water heater last 30 years. Do it yourself. If a plumber does it, just buy a new heater every 12 years; too expensive.
I bought my house in 2020 and the original 1991 water heater was still in it. It made clanking noises and bangs and thumps, so I decided to replace it. The house was owner occupied the first few years after it was built, but after that rented out and obviously the renters never did any kind of maintenance at all. so by 2021 when the new water heater was installed the old AO Smith was 30 years old. Now I have to do the maintenance on it and I would really like to see and easier way to drain it.
Is it possible to add descaling solutions or any other available materials in the market to dissolve all the sediment properly , I would appreciate your kind reply
I'm glad I recently subscribed. You have a lot of obscure homeowner knowledge, and I moved in to my first house about a month ago! Thank you for making this info freely available to the public! P.S. I had no clue they made these with a vacation mode!
I’m not sure if we have the same set up in Australia only because I’ve never seen or heard of this procedure so I’ll be looking into it. I said this before and it’s true your channel is getting bigger and better. I’m loving this path with all different trades thanks for showing this clean out method
Just had a new water installed two days before watching this video and definitely will make it once a year flush. I probably will install a bigger ball valve.. minus well seeing its new
@5:31, so do you shut off the hot water line when doing the power flush method? I gather it's fairly safe to open the drain valve while there's pressure on the tank. (heat, cold water line in, full volume of the tank) That's the only thing I've been apprehensive about, just opening the drain valve on a pressurized tank...
I just replaced a GE water heater 40 gallon. I did flush only once or twice in 16 years. I have another one on another part of house that is from 2000 and still going strong. At this point dont think I'm gonna touch it till it croaks. My ge one I didn't flush as I should because the plastic drain would keep leaking for a month afterwards..not a ton but a continuous drip of probably half gallon a day
I recently flushed mine after having to drain it to replace the gas valve that had quit working. I found it helpful to use a hose with two female ends to force water into the water heater from the drain valve. I am wondering what the advantage of opening a faucet is vs. just opening the pressure relief valve on the side of the tank to allow air into the system?
super userful video. very grateful for it. for the power flush, it sure seems like it would be a good idea to turn off the elements just in case you release water at a faster rate than it refills, no? is there some harm that this could cause?
Great instructional video...thanks! Are there any additional steps required if you have an inline circulation pump connected to the drain valve (like unplug the pump, or bleeding the lines differently afterwards)? Thanks again for the informative video...
I have a 4-year-old Rheem 50 gal. water heater with an expansion thermal tank on top. Can I still use the Power Flush method (leaving everything on)? If so, are there special instructions for the thermal tank and how long should I let it flush before stopping the process?
You’d do yourself a favor by changing out the valve to a full port ball valve. It has a bigger opening to allow more sediment to come out. Plus the benefit of knowing when it’s closed or open. After draining is the perfect time to change this out.
Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
Done this before but, this video is a GREAT reminder of how to do it. Thanks. Sure miss my Dad. He always came and showed me how to DIY!!!
Yep...I miss my dad too 😢
@@christhayil8354I miss mine too. But I’d be the one doing stuff instead of the other way around. He came back from the army quite messed up.
But…I can do most anything on my own at least, since I never had any help.
I do wish I had someone to call on tho to do things like this every now and then.
I just replaced a ballast and dang near broke my neck.
@@christhayil8354miss my dad too ❤️
There is always one major problem with flushing/draining a water heater and that is the acutal drain valve used for above purpose. They are typically a hose bib type of valve and these all have a small orifice (about size of your pinky finder nail), This makes it very, very difficult to flush or especially drain the unit. This is especially true for older units that have a lot of built up sediment. As a retired GC whenever a new water was installed I had the plumber replace hose bib type drain valve with a 'full port ball valve' which provides a full 3/4" diameter opening for flushing/draining. Every 6 months I flush into blue 5 gal bucket a couple of times and thats it. If you wait a few minutes for sediment to settle in bucket you can see how much sediementf is removed.
I'm a handyman and I usely do the samething especially when I come across those plastic hose bibs on tanks
I took off the 1/2” valve and put a 3/4” ball valve
@@johnalarcon5006 Those plastic drain valves are a nightmare.
4😮😢😮😮😮😮😮😮😢😮😮😮😢😢😮😢😮😢😢😢😢😢😢😢😢😢😮😢😮😢😢😢😢😢😢😮😮😮😅😢😮😢😢 0:42 0:42 0:42 0:42 0:42 0:42 0:42 😢😢😢😢😢😮😢😢😢😢😢😢😢😢😢😮 0:42 😢 0:42 😮😢😢😮😮😮😮😮😮😮😮😮😮😮😮😮😮😢😮😢😮😮😮😮😮😢😢😮😮😮😮😮😮😮😮😮😮😢😢😮😮😢😢😢😮😮😢😮😅😅😮😮😮😮😮😢😮😢😢😢😢😢😢😢😢😮😢😢😢😢😢😢😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😢😮😢😢😮😢😮😢😢😮😢😢😢😢😢😢😢😢😢
😮😮
You convinced me to do it myself on my 2-year-old Rheem 50 gallon unit. It came with a plastic handle that was so simple to turn after connecting my garden hose. It was a full 3/4" opening. I did the power flush and crimped the garden hose a couple of times throughout the 15-20 minute process. Easy and remembered to write down the date in my owner's manual attached next to the water heater. Thanks for a great video!
Gray presentation. I had to do a flush for a client a few years ago and it was bad. I went to do a gravity flush, relieved the pressure in the system but nothing would come out of the drain. I was afraid the drain itself was broken. So I took a length of copper wire from some scrap Romex and fished it into the drain and it was completely clogged with sediment. We have a ton of limestone here. I managed to free up enough to slowly drain the tank. Once it was drained I removed the heater elements and they were covered in sediment stuck a flashlight inside and I could see about 1½ inches of sediment so I stuck a shop vac hose in a sucked out out. The tank was still in great shape so I replaced the valve and the elements and it's been working great since.
Did you change the ANODE ROD ??
I hope so.
I've never heard of the power flush before. I will definitely use this because the stirring of the sediment should result in a more thorough cleaning.
This year marks the 30th year (thirtieth) year of my hot water heater cranking out hot water and it was installed when we moved in. It may be 40 years old. She rocks super hot water everyday.
Thanks so much for this video.
Mine is over 35.5 years old. Still works great... knock on wood! They don't make them like they used to.
Did it die yet?
I moved into my house in 2014 and it had 2 identical (one gas, one electric) 50 gallon Ruud hot water tanks still working originally installed in 1988. I changed them both because I didn't want to chance it and the home insp. recommended it. The electric one is for the bathrooms and the gas is for everything else (kitchen, laundry, bars, garage, utility). I bought a gas Rheem Platinum 12 year with 2 anodes and an HTP lifetime stainless 5500w elec. But those Ruuds that where in there I doubt, in fact I'm pretty certain they never had the anodes changed. I think the dates on the tanks were 1987. They did have a decommissioned water softener (which I replaced) but I don't know how long they were on the softener. They weren't really heavy like they were all crusted up. I hauled both of them out of my basement myself after I drained them.
I always remove the aerator from the faucets to avoid any possible sediment clogging them up. Also, using the bathtub hot side open works really well.
Hola! 🖐 Excellent video, very useful information. I replaced my water heater about 6 - 7 years ago. The old one WAS SO HEAVY due to all the sediment that had settled, I had moved in shortly before the water heater went out. I now make sure to drain this one every six months, we have some really - extra "hard" water where I live (Southern California). I hope that a lot of people see this video and put this on their calendar just like changing batteries in smoke detectors, replacing filters in the refrigerator, etc. Take care and have a good one, Adios! 👊
Looks like the power flush is the best method and easier to do. Thanks!
Agreed. 👍
Best video I've come across for guidance on how to do this for a gas water heater. Concise, well put together, and informative. Thank you!
This often forgotten procedure not only preserves the heater, but insures your energy costs, gas or electric, go toward making hot water and not toward making rocks. Thanks, Ethan!
Thank you so much Brent, Eco Plumbers, and The Honest Carpenter! My husband and I have to do this for our water heater. We are both newbies at this, so this tutorial is so appreciated!!!
Having grown up in Middleville, MI, I enjoyed the Bradford White callout.
Cheers and great video.
Thank you, thank you, thank you. This was the easiest method I've seen by far. I love how you explained at the end to keep the hot water valves open while you're refiling the tank to get the air out of the system. So many other videos either skip that step or want you to mess around with the air pressure valve, which I am afraid to do as I heard too many horror stories about that.
Excellent explanation. I did a combination of both methods, gravity and cold water pressure. Back and forth also manipulating the drain hose to see if any sediment would break free. As other have suggested, if I run into problems with sediment and have to do another flush I will replace the drain valve with a larger size like 3/4 ball. Ours is 75 gallon so I'd like to extend its life as much as possible before replacing.
I always power flush into a white 5 gallon paint bucket, watching the sediment, emptying it, repeating until I stop getting sediment. If you prefer, one can hold the discharge end of the hose and feel the outflowing stream; you will feel the particles hitting your fingers.
Do you turn of the breaker when you do this power flush ?
@larryb-infl
Yes you need to and don't turn back on until you have refilled with water. Very important make sure you have got all of the air out . If one of the elements doesn't have water around it. When the electric is on, it will burn the element up. @ukram350
@@ukram350 You really don't have to since you are always going to have water in the tank when you power flush. If you do the gravity method then yes, since you'll be emptying your tank and your elements would be left with no water and possibly burning them out.
During flushing process, pulse the cold water supply off and on several times to disrupt and wash out more sediment. If partially or fully draining tank, it would be a good time to extract and check the anode rod. I've also heard that using a garden hose (attached to cold water supply, obviously) with a spray nozzle to spray down into the top of the emptied tank while the anode rod is out can help flush out the sediment.
I've had problems with using garden hose to drain because it gets clogged with sediment -- especially a very long hose to take the water out of a walk-out basement. I may look for a way to transition from garden hose thread to a discharge hose (like blue pool discharge hose}.
I use method one. Just FYI on one point. I save the flushed water in a garbage can and use it later for plants. One more question - what are the pros and cons of each method? Thx for an excellent video.
Are you concerned that over time there could be long term build up of various undesirables in the soil?
@@mitchelcline9759 I checked with my local Sierra Club guys who wholeheartedly endorsed my actions. The contents are mostly calcium salts and the impact on the soil is beneficial. Here in the San Diego area water is critical and I hate to waste water by draining my contents into the street drains.
@@kersi-sandiego6036 i haven't looked into it. I figured the city water part would be fine. I was wondering more about what types of things are produced from electrolysis between the water and electrodes? I've no idea how much or what all gets made from that and no idea what it would do to plants. To be safe i would personally not eat and plants from that method but i also don't know much about it just wondering
@@mitchelcline9759 Whatever works for you. However, I almost guarantee you that the water used at commercial farms and nurseries has far more virulent stuff than what's in the water heater. Anyway you have to do what's right for you. Thanks for your input.
Thank you for this video! I just bought a house and found out that this was something you need to do this. Thanks for sharing now I feel confident to do it on my own!
The biggest cause of heater failure is expansions and contractions from setting the temp too hot. Cracks form in the protective coating and rust rapidly destroys the tank.
My 1989 heater, in hard water CA, works as good as new because I keep the temp low enough to not need much cold water to mix.
Also, I never replaced the original anode rod.
I flush it, with water supply on, every 2 to 3 years. I replaced the small plastic drain valve with a 3/4" ball valve.
I replaced the original inlet tube about 3 years ago.
If the tube breaks you'll get a very short amount of hot water because the incoming cold water quickly mixes with the upper hot water.
Never drain the tank because incoming oxygen will quickly corrode weak spots.
Hey man thanks for the great video. A new home owner here and this removed a lot of fear i had. For real, man, thank you from the bottom of my ❤.
For the gravity drain, another video showed a good idea I think. After the tank is empty, open the inlet valve for 10-20 seconds to agitate the sediment and then drain it into a bucket. Repeat until the water in the bucket appears clear.
I installed my water heater in January 2019 and flushed it today for the first time! (yeah, I know I should've been doing it!). When I just drained the tank, there was very little sediment in it. But then I started a flushing process - Run the water for a few minutes . . . then tuen the cold water on for maybe a minute and then let it drain our. You wouldn't believe how much settlement came out that time! I've been repeated that flushing process maybe eight or 10 times and I probably got a full cup or a cup and a half of just sediment out! So, in my case, the initial draining did almost nothing but cycling several flashings really did clean the crap out of the bottom!
wow - Jan 2019here too! Just replaced anode rod...about to flush ---
@@LeLilley1
I installed 3/4" full port ball valves on the drains of my water heaters, for a much more vigorous flush. Some of the drain valves that come with the tanks have a very small opening, where any sediment larger than about 1/4" will clog it and stop the flow.
In my area, once a year flush seems to be plenty. Anode rods here last about 5 years before it is best to replace them -- I doubt that 5% of owners ever replace an anode rod.
How do you? Open it up?
From NZ.... this was something I hadn't thought of.....maybe it's time I did as we have been in this 2 b.room unit for 20 months now.
Inconveniently, the electric hotwater cylinder130 litres capacity is in the upstairs roof cavity so there's a challenge.
Sooner or later more worryingly it will need replacing...I worry about Cost but also how on Earth the nice plumbing men are going to get it down through the manhole which almost exactly fits the diameter.🇳🇿🌝
This is really excellent. Always great to see an expert do a demo. Thanks!
Just clean a Electronic tank, I take out all the heat core, and you will find the lower hear core hole is big enough for a 1/4 pvc pipe, first put some acid into the tank, wait 15 minutes, I connected a curved pvc pipe to shop vac and start to vacuum all the stuff on the bottom, it's pretty efficient and works well. It's a 2006 tank and after clean out and change the rod & heat core, it works perfect now! Cost: Rod $30 + 2 heat core $34 ........
Best to remove bathroom tap aerator screen before flushing. Scale and sediment will be broken loose and clog screen after refilling tank .Don’t use kitchen tap to vent, refill as they are more difficult to service.
I've seen some tutorials suggest using the bathtub hot water valve to vent since they don't have an aerator screen
You say a properly maintained water heater can last up to 12 years. I installed mine in 2006. I read on a Ridgid plumbers forum years ago that you should drain a couple o quarts of water once a month to get rid of any sediment. I have done that since it was new and the way I did it on mine was this. My water heater is in the garage next to the outside wall and on an 18 inch stand. A pipe from the pop off valve near the top of the water heater runs down the length off the water and out the wall where it would drain onto the sidewalk if needed. I cut a tee into this pipe below the level of the drain valve and then ran a section of permanently mounted hose from the drain valve to the tee and I also installed a ball valve at the tee to isolate this hose from the pipe. Once a month I go out to the garage and open the drain valve and guesstimate when I have drained a couple of quarts of water and then close the valve. Been doing this for 17 years and it works very well and is very easy to do as all I have to do once a month is open the drain valve for a few seconds.
thank you for that really good thorough explanation. i've watched at least 8 videos on flushing a water heater and this video answered my questions.
Thank you so much for this video! The anode prevents corrosion of Fe--it would not prevent build up of CaCO3 & MgCO3 & other salt deposits. A water softener inlet line would prevent deposits from hard water, but as the Mg anodes corrodes, it would be the source of deposits! The Corro-Protec Powered Anode is conceivably the best route but are X 3 more expensive and consume electricity but claim to last for 20 years! And so a combo of water softener and the latter is the best route but is expensive.
When I was living in LA Ca. area I tried to flush my gas water tank 50 gal, because of some video. I even change the discharge to a bigger orifice valve. So I collected almost all of the water and put them in 35 gal drum and use the water for watering the plant while it discharge. I found out that I wasted my time since I didn't find any sediment accumulated, almost all the water are clear since my wife trying to save water. So now I don't flush any water heater, since my first house lasted about 15 years before it leak, on my second house 75 gal tank lasted about 17 years then it started leaking. So I just ignore the maintenance, since the sign of need replacement is when it start to leak.
We had a water heater that made noises from sediment and it lasted 25 years with no maintenance ever done, and we had the hardest water you can imagine!
Given that the tank lasted for 25 years even with all that sediment, but consider how much your energy costs were increased as your heat source had to work harder to get through that sediment to heat the actual water!
@@patrickrogan8974 Didn't really see a change in our gas bill!
@@patrickrogan8974 SO, IMAGING HOW MUCH IN WATER HE OR SHE SAVED WITHOUT DOING THE STUPID THING.
There are a lot of opinions out there that flushing is a waste of time and not to bother.
Mine is 32 years old. Glass lined. I been here 8 years never did a thing to it
For heavy sediment, replace original drain valve with a 3/4" ball valve. Use an old plumber's snake preferably about 2-3 feet long. Open new ball valve, insert snake and then watch all the chunks flow out with ease.
Any video for reference?
be wary not to damage the heating element with the snake
Seems like that could break the dip tube or glass lining of the tank.
He made that quite easier than I thought it would be. Appreciate the info and great video.
Thanks Chuck! Power flush method is especially easy 😄
That was so clearly explained...like all your stuff! Thank you. We have not yet flushed our water heater and since we're on well water I expect lots of gritty sediment.
Thank you very much for this good video and advice. I just got done and all went well. The only problem I had was getting the old anode out to replace it. Once i got the threads to break loose, thought all was good but couldn't pull the remaining rod out. A 10 inch section of it had turned perpendicular to the hole.
Great vid. Would love to see one about anode inspection/replacement/maintenance
Excellent video .. I would recommend to remove the aerator from the tap when bleeding the tank to prevent sediment in the aerator
Wow, I have that exact same gas water heater used for the power flush! That looked really simple. My back door is inches away so I will just run the hose outside into the backyard.
Appreciate the post. However... (here it comes) you didn't pull the annode and check condition. (Amazon has flex replacement annodes for under $30 bucks.) Have rental properties and this step is a MUST DO for tank longivity. Amazing how fast these will corrode away to nothing and then the tank rusts/leaks. (I swear, the makers of these tanks are counting on this.) Down side to this extra step is the first time you pull the annode you'll need a 1/2 inch impact. On super tight from the factory. Breaker bar w/ pipe extension won't work because the tank will want to turn with the rotational force needed to break the annode free. No way to hold it in place to apply force.
great tip!! I likely would used my breaker bar -- thankfully I bought a 1/2" impact earlier in the year.
@@stevenallen1392 thank you so much. I flushed out the hot water tank for 30 minutea. Ran my hot water faucet in rhe bathroom for 10 minutes. Everything is normal now. My water was a rusty yellow color. Tank is only 7 yrs old. Hopefully i dont have anymore issues.
Some cases its pain in the ass to replace the annodes bar. Not all the tanks installed in the open space.
@@scottvan1898 I remember seeing an episode of This Old House where they showed one that was sectioned (like a sausage) so it could be bent and fit in a tight space.
I change mine every 2 years,My glass lined "Self Cleaning" 50 gallon gas tank is now on year 20 ,total pain tipping it off the stupid platform but its necessary, Vegas water too.
I actually use a combination of both methods. I start by draining the tank first. I then use the flush method second. The drain method in itself still leaves debris in the bottom of the tank. I’m guessing you would only need to use the flush method and eliminate the drain method. Good video thanks for sharing.
Jus drain it...fill it while drain hose is attached for a good flush?
@@edubb2491 I drain mine every summer for 10 minutes so far so good. I let the cold water run none stop.
Thank you. NOTHING beats regular maintenance!
The 1st of every month, I turn on the drain valve wide open for one minute. I keep a small section of hose connected to the tank all the time and the other end in the drain.
My water heaters outside in a closet,,, instead of wasting the water down the drain I'd water my bushes and trees with the flush water and did it often this way I wasn't wasting it going down the street or the drain (its an Arizona thing ) but before I invented that ,,i would flush it onto a used furnace filter this way I can see what's coming out and how much and when it stops coming out, this way I can monitor it
Thanks for your work on this video. Brent presented these methods straightforward and understandable to all. I have to drain one at my father in laws house. It makes a gurgling sound and found your info. here. I didn't know about the pressure method by using the water supply to flush the tank. My drain access is slightly higher than the valve on the tank so it should work well.
Good opportunity to test temp/pressure release valve. I also use that to vent the tank when flushing and refilling.
Holy Crap!?! Who Knew?!? Thank you! I had anew heater installed one year ago and I needed to do this. I was not aware of the first method -I will use it. Another terrific presentation.Cheers!
I live in an area with a lot of calcium. It has been my experience that most here get about 18-20 years out of a hot water heater at which point it's time to replace due to the sediment. As a former appliance repairman who also worked on water heaters, two things became apparent. First opening the drain on a water heater, especially an old one is a crap shoot. Some WILL develop leaks. A cap may fix it. Secondly, as a couple of others on here have noted, back flushing does very little to remove the sludge in the bottom of water heaters. There is just no good way to do it with the little hole you have to work with. (This is obviously by design of the mfg.) You'll get some, as evidenced at the end of your hose, but not much. Good luck.
You're absolutely right!
I'm 75 and NEVER heard about flushing a water heater until just last year. It is something I am NOT able to do by myself but I have mine flushed twice a year by the company that does the annual maintenance for my A/C and furnace. I live where the water is extremely hard and wish I had known about doing this 20 years ago. My water heater is soon to be replaced since I have it on the highest setting so that I have hot water.
Hi Ethan: I want to first say how much I enjoy your TH-cam channel and your blog. I am a very new user of power tools with DIY projects -- your videos have been amazing to watch and I have learned much from them. I have tried to find classes in this area, but they seem to be sparse. Have you ever considered offering in-person classes -- they could focus on the proper, safe use of certain power tools (your video on the proper use of a circular saw is great), be project oriented or focus on a specific DIY topic. You are am amazing teacher and I think you'd do very well by offering classes in this area.
I didn't realize it was this easy. I made a contraption with a Y valve switch that shot air from my compressor into the drain valve to stir up the sediment. I probably didn't need it. It was pretty messy. I'm going to see if I can replace the sacrificial anode next.
Great video. Nearly everyone I talk to doesn't ever read their manual. That would inform them that they need to do the flushing periodically. The "Master Plumber" said the heater came from his company. That would indicate that they did the install. I noticed the connections were created directly from steel to copper at the water in/out pipes. You really don't want to do that. You need 6" of brass between the 2 metals to prevent electrolysis...That's the way I was taught anyway...
Drive me nuts that water heaters come with steel nipples. A few more bucks for brass would prevent so many problems down the line.
Yes, it was surprising he pointed out the electrolysis corrosion without pointing out it was caused by an error that took place during installation.
Thanks for the informative video. I attach a small mesh sock or nylon netting on the end of the hose to see if any sediment is present in the tank. Thanks again
Last 12 years? When I bought my house in 1998 it had a gas water heater that was installed in 1978, I seem to remember it was AO Smith, it served me perfectly fine for about 15 years, it started to have a small leak around the drain valve inlet I guess where it was welded on, so I replaced it, after I took the tank out I cut it open, the inside of the tank was a nice clean grey no corrosion, but about a foot solid chunk of mineral buildup on the bottom, which was why I was never able to drain/flush it- the previous owners obviously didnt, but that water heater still lasted about 36 years!
This was interesting and easy to understand, thanks! I'm having it professionally, but it's always good to know what they're going to be doing and how they're going to be doing it. Also, what kind of screwdriver did the plumber have that holds interchangeable bits in the handle? I have to get me one of those!
Pressure method highly effective for removing loose sediment. Thank you. Just got done with mine. 😃
Great video!!! I always thought that you HAD to turn off the supply. I've had my water heater for three years with no flush, recently moved into home and didn't feel comfortable messing with the old gate valve. My luck that the valve will be older than Methuselah and will start leaking if I start screwing around with it . Eventually I'll have it swapped out for a ball valve. I wanted to put my burner on pilot, connect my hose and like the video slowly flush the water heater until I get clear water.
In talking to a Plumber of 40 years he told me flushing is a waste of time. Basically you don't remove much from doing it you just channel the debris then it settles back. I have owned two water heaters, 1st lasted 15 years and second 12 years and neither was flushed. Only thing I do is make sure sufficient make up air for clean burning.
Cheers
If you flush and replace the anode rod, you should get 20+ years out of your tank.
Best vid I've seen for flushing. Love that you provided two methods!!
When doing the gravity drain method would it not be better to allow the first minute of flow when the pressure is turned back on to flow out the hose to prevent any residue of sediment to flow out the drain rather than into the system so as to not clog things at faucets?
I’ve seen a lot of differing opinions on whether you should or shouldn’t flush water heaters. I power flush mine every couple of months.
I'm guessing the people voting to *not* flush are the heater installers. LOL.
thank you. He seems like a honest plumber who I'd hire without question.
Another very helpful video for DIYers. Thank you so much.
You said the burner stays on. Nothing is changed except that the valve is opened at intervals, right?
Thanks for the video, i just power flushed my water heater yesterday, I'm also interested in these electrical anode rods that dont get eaten away like the typical aluminum and magnesium rods
Thanks. I have question.
While refilling the water tank, you will leave open the faucet for the hot ? So when are you going to to turn off the faucet if the water heater tank is full? How do you know if the tank is full.
Thanks so much for your response
thank you so much. I always thought running water was better than draining it with gravity. was able to get rid of sediment in minutes rather than hours.
Thanks, no time wasted very well explained!
Great video and perfect timing! I have a Bradford White installed in 2005.
*Some folks say not to flush the water heater if it hasn’t been done annually, is there any truth to this? I’ve owned the house for a little over a year, so no idea if the WH was flushed on a regular basis.
I've practiced this method with the following suggestion, run the hose to a 5 gal bucket to actually see what is being flushed out. Sediment from the water and from the anodes dissolving can be quite nasty. Also, I've changed the anode rods to extend water heater life but have since converted to an electronic cathodic protection.
What’s this electronic cathode protection??
Bought a water heater over 10 years and it is an electric type. Difference between it and the newer ones is the clean out hole. This makes the removal of the sediment almost 98 percent. Do to being able to reach inside and actually scoop it out.
If the tank has a lot of sediment and nothing comes out of the drain valve, I've hooked up an air hose to the hot side and a hose to the cold side and blow the water out that way. Doesn't always work but most of the time it does.
Power flush is definitely better since thermal shock to the tank will be less. If you plan to do the drain method, you should turn off gas/electric and let it cool down for a few hours first. If you drain while water is still hot, you run risk of cracking the tank when only air is available for it to exchange heat with.
Thanks for the tip. I did turn the tank off first, but I did not wait more than 15 minutes to drain it. Fortunately I live in Florida so the ambient air temperature is not quite as different as it could be up north in the winter in someone's basement or attic.
@@terryvlunsford1610 thank you so much for the tip.
I turn the water heater off and take a long shower and drain the hot water out that way, then drain it under pressure.
I installed a water softener in my home and never looked back . Everything with washing clothes and showering and using tap water is so much more cleaner because of less corrosion on tank and also saves $$$. On soap. My tank is is 10 years old and so far pretty clean of sediment.
@@blindsquirrel7802 Do you turn off both the COLD water inflow and set the temperature setting to VACATION to empty the tank before turning back on the COLD water inflow to agitate the sediment and let it drain?
I flush my tank into a 5 gallon bucket and can readily see the sediment in the bucket. Empty the bucket and repeat till there’s no more sediment.
Good tip, thanks.
Good to know. As you flush- does the sediment settle that quickly? I'd of thought flush, wait a minute or more, flush again- but its just a few seconds.
Great video but what about exercising the pressure relief valve? I exercise that everytime i flush my tank too.
This was very, clear, easy, and effective. Thanks.
A few questions. For the gravity flush method, he didn’t open the relief valve at the tank. Isn’t this necessary? After the flush, he said to make sure no air is left in the pipes into the house. How do you ensure this - just by seeing a constant flow of water at the faucet? What happens if air is still in the pipes at the faucet?
often have had good results from reverse flushing from the hot outlet. Easy to do. I turn off cold supply, empty tank, leave drain open, and then cap off any threaded single spout in the house and turn on that hot and cold together, causing cold water to flow in reverse to the tank hot outlet, and flushing down the walls and floor of the tank.
Which method is most effective for flushing out the sediment?
I might have missed it but how long would you do the power flush method? Does the timing depend on amount of sediment in the tank? I'm getting ready to tackle this task soon and I know there is sediment in the tank. I really enjoyed seeing the two methods.
I just did mine after this video and I let it run until the water was clear (at first it was a tiny bit foggy, but you can't really see sediment build up like that). If you pinch your hose every few minutes you can often times feel the sediment smacking in the hose where you pinch it, I just power flushed until I could no longer feel the buildup in my hose when pinching. If you attach a thigh high sock to the end of the hose with some rubber bands or a clamping mechanism, the water will continue to flush but the sediment will be caught in the thigh high sock. After a few minutes you can check the sock to see how much sediment has been caught. Another video said if there's more than a few inches of sediment, you have heavy build up and might need to do more. Another method is to drain into a bucket, that way you'll see the buildup as it collects (if it's bad).
I'm no pro myself, so I'd just say trial and error, you can always do another power flush if needed or if you are hearing popping etc in your tank. I drained mine for 15 minutes personally, the first 5 minutes I actually could see sediment shooting out of the exit end of the hose because I hadn't flushed my tank in over a year and have very hard water.
Hopefully that helps you if no one else has replied anywhere else.
I believe he said he does it periods of open/closed with the valve till the hose is cold from the water.
This was extremely helpful & clearly explained. Thank you so much for this information. Be well.
Thank you, Millie!
@@TheHonestCarpenter yeah I was also a Bradford white hot water dealer and I had to get out of it due to factory mistakes and way to many came back leaking and of course Bradford white doesn't want you to ship the bad tanks back due to cost but they do pay awesome for the the promotion of their products though
@@TheHonestCarpenter and best way I have found out of all the tanks out there regardless of brand,is to convert it to bottom feed and it's easier than what people think
Thank you you me feel better about doing my hot water tank now I think I can do it. My wife and I moved here 5 years now and the tank is electric so I do need to do soon .
Full port ball valve is good. The best is to drain and clean water heater is to drain just below the outlet and remove bib or element. Get a wet/dry shop vac and use a 3/4" OD hose connected to shop vac and suck out the sediment. You may need to use a stiff fishline to breakup sediment. Move sediment away from around the sides into the middle for easy sediment removal with the hose. Alway fill up tank to just below the outlet before vacuuming sediment again. You need water to mix with sediment to remove. Repeat this until sediment is gone, usually 6 times. I am going on 16 years with a 6 year water heater for my personal heater (electric). It is clean and working well. I clean it every 2 years and takes me 45 minutes to do. Where I live, we do have low calcium, sodium and limes. I am a plumbing contractor and have done this for customers for decades. You can make you water heater last 30 years. Do it yourself. If a plumber does it, just buy a new heater every 12 years; too expensive.
I bought my house in 2020 and the original 1991 water heater was still in it. It made clanking noises and bangs and thumps, so I decided to replace it. The house was owner occupied the first few years after it was built, but after that rented out and obviously the renters never did any kind of maintenance at all. so by 2021 when the new water heater was installed the old AO Smith was 30 years old. Now I have to do the maintenance on it and I would really like to see and easier way to drain it.
Is it possible to add descaling solutions or any other available materials in the market to dissolve all the sediment properly , I would appreciate your kind reply
I'm glad I recently subscribed. You have a lot of obscure homeowner knowledge, and I moved in to my first house about a month ago! Thank you for making this info freely available to the public!
P.S. I had no clue they made these with a vacation mode!
😊
I’m not sure if we have the same set up in Australia only because I’ve never seen or heard of this procedure so I’ll be looking into it. I said this before and it’s true your channel is getting bigger and better. I’m loving this path with all different trades thanks for showing this clean out method
Just had a new water installed two days before watching this video and definitely will make it once a year flush. I probably will install a bigger ball valve.. minus well seeing its new
show a pic of where you connect the air hose. Awsome technical guidance.
@5:31, so do you shut off the hot water line when doing the power flush method? I gather it's fairly safe to open the drain valve while there's pressure on the tank. (heat, cold water line in, full volume of the tank) That's the only thing I've been apprehensive about, just opening the drain valve on a pressurized tank...
I just replaced a GE water heater 40 gallon. I did flush only once or twice in 16 years. I have another one on another part of house that is from 2000 and still going strong. At this point dont think I'm gonna touch it till it croaks.
My ge one I didn't flush as I should because the plastic drain would keep leaking for a month afterwards..not a ton but a continuous drip of probably half gallon a day
Do you think by end of January 2023 Shasta, Oroville and trinity will be full pool?
I recently flushed mine after having to drain it to replace the gas valve that had quit working. I found it helpful to use a hose with two female ends to force water into the water heater from the drain valve. I am wondering what the advantage of opening a faucet is vs. just opening the pressure relief valve on the side of the tank to allow air into the system?
super userful video. very grateful for it. for the power flush, it sure seems like it would be a good idea to turn off the elements just in case you release water at a faster rate than it refills, no? is there some harm that this could cause?
awesome explanation. question during the power flush should put a stocking at the of the hose to see if any sediment is present? tia
Great instructional video...thanks! Are there any additional steps required if you have an inline circulation pump connected to the drain valve (like unplug the pump, or bleeding the lines differently afterwards)? Thanks again for the informative video...
I have a 4-year-old Rheem 50 gal. water heater with an expansion thermal tank on top. Can I still use the Power Flush method (leaving everything on)? If so, are there special instructions for the thermal tank and how long should I let it flush before stopping the process?
Fantastic help guys! Thanks from Cape Breton, Nova Scotia.
You’d do yourself a favor by changing out the valve to a full port ball valve. It has a bigger opening to allow more sediment to come out. Plus the benefit of knowing when it’s closed or open. After draining is the perfect time to change this out.