Tips for removing a car alarm system
ฝัง
- เผยแพร่เมื่อ 25 ม.ค. 2016
- If you're about to remove a car alarm system, Watch this before you do so you'll know what to look for and maybe some things to avoid doing to get a good result. If we can be of more help contact us through our site at :
www.lesscoesales.com
There are few things more embarrassing (or more annoying, if it’s a neighbor’s car) than a car alarm that won’t shut off. There are a number of reasons that a car alarm won’t turn off, and a few different methods you can use to silence the shrieking - and end the embarrassment.
Part 1 of 1: Turning off a car alarm
Materials Needed
Needle nose pliers (or a fuse-pulling tool)
Owner’s manual
Step 1: Familiarize yourself with the alarm. While it may not seem to be the ideal time to be reading your owner’s manual, in many cases user error is the problem. Verify you are following the correct procedure to shut the alarm off.
Step 2: Start the car. Put the key in the ignition and try to start the car. Almost all alarms, both factory installed and aftermarket systems, will shut off and reset when the car is started.
person putting key into drivers side door
Step 3: Use your key to unlock the driver’s door. This will usually turn off and reset the alarm. In the event that the driver’s side door is already unlocked, lock the door and then unlock it again.
person pulling fuse out of fuse box
Step 4: Pull the fuse. A factory-installed alarm will have a fuse in the fuse box; pull the fuse to cut the circuit and shut down the alarm.
Look for the fuse box on the left hand side of the steering column. Fuse boxes usually have a fuse diagram on the lid of the fuse box.
Most alarm fuses have an alarm label on them. If the fuse is not labeled, consult your owner’s manual for the location of the alarm fuse.
Tip: Some vehicles have multiple fuse boxes - check your owner’s manual for the location of the various fuse boxes.
Remove the fuse. If the alarm shuts off, you have pulled the correct fuse. If the alarm doesn’t shut off, re-install the fuse and try another one until you find the correct fuse.
Once the alarm has shut down, reinstall the fuse and see if this resets the system. If the alarm starts up again, it is time to bring in a pro to repair it.
If the alarm system is an aftermarket item, look for the fuse in the engine compartment. Consult the owner’s manual if you cannot locate the fuse.
person disconnecting black negative terminal
Step 5: Disconnect the battery. This is a last resort, as it will reset all of the electrical systems in the vehicle and your vehicle will not start until the battery is reconnected.
Disconnect the negative terminal (the black one) from your battery. The alarm should shut off immediately.
Wait a minute or two and reconnect the battery. Hopefully, the alarm has reset and will not start up again. If it does, try removing the battery cable again.
Tip: If this does not work, leave the battery cable disconnected and contact a mechanic or alarm installer to repair the system.
Step 6: Maintain your key fob. Most modern cars use a key fob to lock and unlock the doors and shut off your alarm. Unfortunately, the fob will not work if the batteries are dead, or it is simply not working.
If you need to press the unlock or lock button of your fob a number of times before it works the battery is probably going dead and should be replaced. A malfunctioning fob should be replaced as soon as possible.
Hopefully, if you’ve tried the above steps, the alarm has stopped shrieking and all of the dirty looks from the neighbors have stopped. If it was necessary to unhook the battery to stop the alarm, a professional mechanic, such as one from YourMechanic, should inspect the entire system to make sure everything works normally. - แนวปฏิบัติและการใช้ชีวิต
![[MIRRORED] LISA - ROCKSTAR 🎸 MV version #LISA #BLACKPINK #ROCKSTAR](http://i.ytimg.com/vi/-U58DuCCtZk/mqdefault.jpg)
I'm demo'ing a circa 1999 Viper 800 ESP alarm that has strarted going bonkers after 23 years. I suppose now we know how long it takes.
When he said, there were NO mods to the factory wiring harness, I was thinking , that's IMPOSSIBLE!
There has to be an ignition wire that they cut and wired to the alarm to interrupt the starting procedure !
Sure enough, at the end of the video, he says you have to REPAIR the ignition wires and possibly a starter wire that got cut.
Then he spent really no time on that, the MOST important part of the procedure.
Anyone can just go ripping stuff out. It's the repair that is the most important aspect of the process.
EXACTLY WHAT THE HELL I WAS THINKING!!!!!
Thank you! My Vitara alarm went crazy today, beeping and locking and unlocking the doors continuously while driving. 3:50 into your video, my problem was solved. Removed the module and that was it.
oh my god, i had been battling a shitty alarm on a 1991 CRX si for days. I replaced the starter, and the car never started after that. It ended up being that starter relay killer. Immediately after watching the video i went out and cut the red and black wire that had been spliced to the ignition hot wire..connected that back and boom, car fired up no problem..thanks so much
Thank you so much, with your explanation I could do it even though it was a different system.Bravo 👏👏👏
You rock brother i was stuck with my key fob activating the alarm and i could not start my Dakota and with this video i was able to remove the module and drive my truck Thank you for your detail video.
This guy knows his stuff. Watched a lot of other videos wasting my time.
Thank you so much for the video!! I've finally taken out those car alarm boxes in my 4runner.
JPO C I’m going thru issues with my 4Runner alarm! The remote battery died I changed it and now the truck won’t respond to the the keys on the remote. I’m ready to push it into the river haha
This was less technical help than I was expecting but you did make it seem less scary. So I opened a beer and pulled out my meter and rebooted my mindset. Got my finicky alarm to at least stop and got my truck back on the road. I think I'll take it to a pro soon enough to remove it and get it close as possible to oem, but I figured I should thank you
Thanks for the video. You helped me remove the garbage from my car.
Thank you !! I wanted to remove an old alarm system. This video exactly showed me how to do it.
After doing all that, the hardest part is getting up off the ground, knees lock up!
samdomding mm. How to install a starter for a Mazda 6 2008
Antonio Guadalupe h
Wah!
Facts...lmao
Thanks for the very informative video. I successfully remove my alarm from a 2006 Honda CRV after watching this.
This is the first video on car alarms I've seen that actually gave me the information I needed, thank you.
Im glad it was helpful
excellent video, i was worried that the car wouldnt start, but you have made it less complicated, thanks
This was the most helpful video on the entire internet!!! I've had issues with my alarm ever since I disconnected the battery cable. This video helped me resolve that!
Thank you so much!
Thank you for taking your time and doing videos
this worked so well! thank you!!!
I used what I saw in this video to remove a prestige alarm that was installed in 1998 in a 98 Corolla. The prestige alarm wasn't allowing my 98 Corolla to start...so with this video and another explaining those alarms I was able to remove the shock sensor and problem was solved.
Hi, I'm curious if when the security system was preventing the start, was it turning over? I'm trying to diagnose if my no start issue is due to the alarm system. When I try to start, I don't get a click at all from the starter.
Lolo thank you for letting her use the channels, based on what they been doing.
Great video. Well instructed and great info.
Nothing i hate more than buying a used car with an aftermarket alarm, dreading for the day it stops working, today that happened on my honda, so annoying 😁 this video helps a ton tho!
ps. if i remove any wire from the alarm box, the car wont crank over, so i guess in some alarms removing the wires from the mainbox does equal a non-start / non-crank condition
You might want to mention in the description that this is for aftermarket alarms and not the factory alarm. It may seem obvious, but to some, it's not... Thanks for the video..
Wow..thx I just asked this..for factory alarm how can I disable it?
will this work on removing the alarm from a 2009 kia spectra
Great video thanks for posting . Getting ready to try and take out my car alarm with remote start on my Dakota {old clifford alarm.} stopped working one day . know the truck when it gets at operating temp shuts off . I'm thinking its the alarm . it was installed at least year 2000. Any suggestions Please! Do yu think it's the alarm ? thanks
Nice vid.
The newer systems no longer have a chip key hidden in the harness but can still interfere with programming in an All Keys Lost scenario so how do you identify the remote start modge? They usually need to be wired back to original. Appreciate any input. Thanks.
Subscribed and 👍👍👍
thx...great video..
.your kind help will do ....I have a base car no alarm ..I paid to install aftermarket alarm...now I want to take it out? do you have a how to video to help me thx again
Scotty Kilmer explains the process much clearer.
Thank you!
I have been battling an APS787C by Audiovox for years. You told me how to disable it from the inside, but I have a hunch that it is killing my battery. Going to try this and see if it gets my 07 Xterra finally back to reliable.
Will be looking at an 02 ranger i just aquired having random no crank no start issues. Car has an aftermarket viper system ontop of the factory alarm. Do you think the viper system could be interfering and causing starting issues?When i twist key to START the dash lights remain lit but it kills power to the radio and possibly other things.I dont know what system it has but the fob says 0890. I would like to remove it altogether.
Hi! My 98 honda crv ignition switch malfunctioned, and while swapping out with a new one, I see the old ignition switch wires have a few splices in them that connects to both a long ago disabled aftermarket alarm system, as well as wires that seem to go toward my car circuit wiring. One red wire appears to go through my firewall and connects to the horn.
The alarm system has not been working over a decade, and my car stills runs before the ignition switch failure. Not sure what previous mechanics have done to help bypass the starter kill function, as well as making the electric locks only manually operable now.
My question is, can I disconnect the wires from the alarm module box going towards both the ignition switch as well as a few clip- in connectors that connect from the module box wires to what seem like some type of plug ins to my car's own circuitry? I need my horn to work properly in order to pass state inspection. Any grounding issue I need to worry about regarding the way the old alarm wires were configured into my car? Or perhaps relay of some sort that I just pull off to disconnect the whole alarm? Thanks in advance for any advice you might offer me.
excellent video , thanks
Glad it helped
My mechanic told me that my 2000 Mustang has a circuit cut in the alarm system which is draining my battery quick & have to get a jump start every time. Will disconnecting the main alarm box stop it from draining & I’ll be good to go?
Hi ,great video I am a bit nervous about removing the alarm from a mitsubishi montero it is an audiovox prestige model aps-250.my battery just dies and i think it is the alarm,I normally keep it shut off with the valet switch but now when I recharge and reconnect the battery it just goes dead do you have a video for that model thanks for any help,or what would it cost to be removed by a professional.thanks
Hello Sir, I have viper remote start on my 2012 tundra. I purchased the truck from a dealer who did know anything about it and doesn't looks like its working, except for unlocking and locking doors. I just realized it was poorly installed and I want to remove completely. Is there anything I need to know about it, will it have any impact on factory functionality or programming?
Just finished many thanks 👍🏻
No problem 👍
I have an 03 Aztek. My key is lost and my passkey 3 security module got broke. I have a passkey 3 from the 04 Aztek. The ignition assembly is different between those years. The 04 rally bolts onto the steering column whereas the 03 IS built into the steering column my lock cylinder has been drilled out do you release it in order to use the lock cylinder from the 04 which is not a fit. What do I need to do to fix this the easiest way. Will the same principle work as in with the gentleman who lost his key? My car has been down for three and a half months
What about oem car alarms that malfunction? Can I unplug that and toss it? I think the box is shorted out.
why did u not start the car after removing the stuff it turn over little bit did not run.
The purpose of this video is to encourage you to remove the alarm on your own so that you will hire an experienced car alarm specialist charge you double to figure out what you did wrong.
i have an anti theft system on my Impreza. and its annoying. before you start the car. you have to
scan/tap the remote under the dash. its really annoying when you're in a hurry and its freezing outside. previous owner installed it and he thinks its pretty cool.. NOT!
is this type of system gonna be the same process of removing it?
I know this video is old but I have a question. Any way to bypass the panic alarm on a 05 Grand Cherokee? I just want working lights and turn signals. I had the ECU tuned to run on the key without the imobilizer tripping. Locked door. Went to unlock it. Alarm won't shut off
Hello i am having a no start no crank issue lights on dash come on and gauges work but head lights and heater fan do not! have a relay in internal fuse block clicking with ignition?
Thanks!
I bought my truck at a auction and it has one of these fricking things and my fuse for my dash constantly pops along with my running lights I cant drive at night is there a chance that this safety system could be causing it
09 Santa Fe, alarm keeps going off randomly.
I removed the horn fuse to get rid of the sound but have people telling me daily they see my lights flashing all day.
My vehicles anti theft is oem from hyundai, if I remove the anti theft fuse will my vehicle still start after? I’m worried to remove it and have to take it to the dealership for them to reset it or something.
Thanks.
do you know anything about 2003 Saturn Ion alarm
Podrias hacer un tuto de como quitar la alarma de fabrica de un stratus 2000 amigo, tengo problemas con la mia
My 99 solara has a basic python 2007 era alarm with unlock buttons, the alarm stays off as between battery changes etc as long as it wasn’t armed before I guess, but it’s draining my battery too fast and I’m not sure why so I’d rather just get rid of it, can I just unplug the positive cable from the battery?
i have a 01 jimmy i have a after market remote start hooked up it came with this car when i got it. the problem is it has 2 different alarm systems on it and both work one is factory the fob i guess they call it which i have problems with going off and car does not start. i found the remote start unit under the dash and it came with two remotes. the factory alarm came with one. i cant find the factory alarm need help to take it out. ive already reset and reprogramed it numerous times. i have taken out the remote start thinking it was the problem and wired a new alarm system in and worked fine but after every hour i would pust the unlock botten it would unlock the doors and set the alarm off. after i start the car to shut the alarm off. i push lock and unlock it would not go off any more untill i wait about an hour again. also the remote start doesent honk when i had it in. but when i use the factory remote it honks. and thats how i figured it had 2 alarm hooked up and working at the same time
Where do I get a cigar lighter wiring diagram for a 03 Chevy Tahoe?
on a 2007 Dodge Magnum if i remove the alarm would the car start ?I replaced the ignition it started then someone hit the lock buttons while in the car activating the alarm so now the security light is flashing and it will not start,i dont have a original key so cant reprogram nor do i have a key fob
I have a 2007 chevy impala. It won't start. I'm thinking it has something to do with the alarm. It's not a factory. Its an auto page I believe. I think that might be the reason it won't let my car start. Do you have any idea what it can be? Anything will help. Thank you.
I’ve had a car for a while and we recently replace the motor could that have tripped the alarm and shut everything off like the fuel pump? I checked the kill switch and the pump was also replaced
I have an 03 BMW 745 li when I replaced the battery the car wouldn't start it seems the owner before me installed an aftermarket alarm and remote start how do I remove this without any key fob for aftermarket alarm and remote start
What brand and model is the new alarm and the power probe?
I got a 93 Buick regal with a bulldog alarm system and I don't have the fob. Not even sure if it works. I need to install a keyless entry. Help
Thanks for the video, I have a really basic question regarding the wiring since I suspect I developed a short, are car alarms grounded to chassis/battery? My fob started acting up to the point I had to be right next to the car to unlock it, and now any electrical load messes with my idle (very bad when raining/humid), i'd like to test if the alarms wiring is to blame, where should I start? Thanks.
If the range is the issue, thats either the alarm's antenna, location or a low battery in the remote most likely, Id start there.
Hi where can I get a new remote system for a 03 Malibu my car tends to not start whenever the anti theft lights comes on and kill my battery life.
Hi how do u remove or bypass 93 Maxima Nats alarm system car won't start
First thank you for the video it helps to understand what's going on with these things. Second I have a 2011 Honda Accord and my alarm keeps going off. I've unplug the hood latch. Removed all components from the aftermarket alarm yet my factory alarm keeps randomly going off, usually at night when it cools down. If I disconnect the orange wire in the driver's door will that disable the alarm? I just want to disable the factory alarm not necessarily remove it
try unlocking the driver door with a key 2x and call me in the morning..
@@Lesscoelectronics Will do thank you. What's the number to reach you?
904 342 5491
I bought a car with an alarm, a "Viper". The passenger door doesn't lock, and neither door unlocks with the key fob. The dealership won't mess with it until the aftermarket alarm is removed... Will a shop charge me to remove an alarm? I'd like to go back to factory, with just a usable key fob without the aftermarket alarm. Any suggestions? Thanks in advance
My car locked up and the engine won’t even start now and the alarm is going off, because I lost my key fob and I had to use the spare key and now it just won’t turn on, will doing this help me with that it’s a Chrysler 300c 2005
Where is the alarm fuse located on a 2010 honda ? My alarm won't stop going off and my gear shift is locked in park and wont go into drive. I unhooked both sides of batteries and when I reconnect the battery the alarm is still going off
My 1994 S10 Blazer starter kill disable relay has 4 wires. Orange, white with black stripe, red, and black. What wires are okay to cut and leave alone unreconnected and what wires need to be reconnected? I don't want to mess anything up and your videos have been very helpful, but I'm confused about the starter kill disable relay. Please respond asap.
Towne Automotive Photography Ii
Maybe you can help me out. I bought an rsx with an aftermarket alarm installed. It didn't seem to work so I got removed. After doing so a check engine light came on (p1164 A/F sensor) I know it's not the sensor because the only thing that was changed was the removal of the alarm. Basically when the alarm was removed all the wires from the aftermarket system was cut off and I don't think any was butt connected or soldered. Any ideas on what it could be before I start tracing each wire one by one in the wiring diagrams ?
Nice vid !! Im needing to find out how can i bypass a 04 kia sorento Not turning on after battery swap...
factory or aftermarket alarm?
will this work on a 07 nissan quest?
I'm putting an after-market alarm on there I forgot to say that I got everything hooked up except for the lock and unlock I can't find the module
Hope I could see one on a nissan roug 18
Hi I'm having a Vat system problem as well on my 2005 Cadillac cts my fob isn't working as well an while I'm driving I'm hearing scratching under my dash can you pls help me out an reach out to me
"Step 2: Start the car. Put the key in the ignition and try to start the car. Almost all alarms, both factory installed and aftermarket systems, will shut off and reset when the car is started."
If the alarm system features an immobilizer, would the key start the engine?
Hi you make it looks so easy. I have 2003 ford ranger with thief’ light is blinking and car won’t start, if I were to disconnect the alarm would the car start?
the only reaso it doesnt start would be because the starter kill relay is leaving the start wire open and is is defective
I have a renault megane 3 and I can’t leave a window down for the dog without the alarm going off. Even without the dog in the summer I have to park with every window closed otherwise the alarm goes off after a ten minute period or so. It’s so annoying, I’d like to disable the whole alarm system. What’s the easiest way to do that please?
I have a 2002 GMC YukonXL. It won't let me set the alarm & I just bought a new battery. I just want to lock it manually. Please help!!!!
I just cut all my wires where they connected some of were just splitting.
I have a 2000 Durango that I lost the key to and would like to install a remote start system as well as new security, the original security set off when I wired the ignition to buttons after some time of driving and left me stranded
thats a pickle, youll need a locksmith on that one..
Worked, Bro. Thanks! You gave me the confidence to do this by myself. What do you suggest to do with the old T-taps- -remove the clip on part or leave them be? I'm not putting in a new alarm.
If youre interested in getting fancy just leave them..
i have a dodge 2013 avemger and my factory alarm isnt working
does any body knows how to make the car go off in the newest chevrolet cars, i cant find the fuel pump wire to make the current cut off, id supoused i could used the releys cut off but im really stuck on this, tank u to all of you
Can some one help me with my auto mates model AM7 alarm system with a 4 button remote really need help
I removed my alarm but my car cracks but is seems like there is no fuel going to the engine I don't know what to do it's just stuck now
Thanks
Welcome
Is this for factory alarm?
I have a 96 acura TL my aftermarket alarm got ripped out and now my car won't start what can I do to get my car running is there someone that can help me out
also when i hooked up the new alarm when removing the remote start one. the new one came with a chirp siren and when the alarm went off the horn went off not the chirp siren which made me believe even stronger that there is another alarm interfering with the new one somewhere. still can't find the factory alarm that's giving all the problems
Denalfreings
, I kHz Christmas
How to remove chevorlet impala 2019 alaram tone
Great video. My Viper car alarm s blue light stopped blinking. The remote still locks and unlocks the doors. The lock and unlock chip also stopped working. But when I pressed the Panic button, the alarm went off. How do I fix this. Appreciate any info.
it may be in valet mode, hit lock unlock lock in quick succession, that ought a fix it.
Try taking it out of valet mode.
How remove factory alarm system rav4 2014
I have a question. In the 06 Camry LE is there an alarm system in that same area your working on. Because it won't go into programming mode when trying to program the fob. I found the receiver for the keyless entery on the back panel near the rear speaker's. But I don't know if it has another receiver in the area your working on. Do you know?
What model is the alarm, do you see it on the module?
Its the receiver door control. As far as the model I don't really know if the trw on the corner is the name of the model. But at the top right corner of the module it says TRW.
I have a 1997 Toyota Camry CE e has alarm on it but I'm putting an after-market on it and I can't find the module for the unlock and lock on a I looked everywhere and can't find it
drop the driver side underdash, that will expose everything
my 2007 Ford Fusion battery keeps getting drained and autozone thinks that the alarm system is the problem. Would this be a good solution?
I have the same problem. I'm going to have my Viper removed or install a new brain.
I bought a 1998 honda prelude type SH. the previous owner disconnected the factory car alarm.
I was wondering ...how can I EN-ABLE the alarm on again so that I can program the remote I bought.
I saw the *brain/mother board* of the alarm but have no clue how to turn it back on.
Whats the alarm model?
I just found out that my 2010 Escape has a Ford dealer installed VSS System (7l3z-19a361) and that's why my horn's going off when opening doors. I found a 2012 Ford installation manual but they show it installed and tied into the steering column area. Mine is by the glove and I see it's tapped into the center console harness by the fuse box. I wonder if I can just start pulling taps off the wires.
There is usually a wire schematic on the back of the main alarm unit, That'll show you what goes to what. If you need a full manual - Audiovox now owons code systems and you can get their tech dept at 631 231 7750. good luck with everything..
Thanks! I have the schematic for two years later on same generation vehicle, so that should suffice. Same unit, just located and tapped differently on mine. My main concern is whether there is anything I could get into trouble with, but I know wiring well enough and it's still an aftermarket system. Gonna follow your lead, pull the battery negative, unit power wire first then just trace back the harnesses. Appreciate the AudioVox tech number. Subscribed.
Is this car you'r working on a 300c if so do i have to replace the box module if so what is the price and part no. for the replacement
What module are you referring to?
can someone help me identify the trigger wire for the alarm under the dash for a 2018 accord so I can add a shock sensor to the alarm? thanks
FUNCTION
COLOR | POLARITY
LOCATION
REMOTE START & POWER
Constant 12 volts
WHITE (50A)
IGNITION SWITCH WHITE 5 PIN CONN, PIN 1
Ground
-
CHASSIS GROUND
Ignition #1
GREEN (+)
IGNITION SWITCH WHITE 5 PIN CONN, PIN 2
Accessory #1
ORANGE (+)
IGNITION SWITCH WHITE 5 PIN CONN, PIN 4
Accessory #2
RED (+)
IGNITION SWITCH WHITE 5 PIN CONN, PIN 3
Starter #1
BLUE (+)
IGNITION SWITCH WHITE 5 PIN CONN, PIN 5
Brake Pedal
LT GREEN (+)
BRAKE SWITCH OR DASH FUSE BOX GREEN 36 PIN CONN, PIN 19
Parking Brake
LT GREEN (-)
PARKING BRAKE SWITCH
Clutch Pedal
BROWN (-)
CLUTCH PEDAL SWITCH 2 PIN CONN, PIN 2
Rear Defrost
BROWN (- LATCHED)
BENEATH DASH FUSE BOX WHITE 28 PIN CONN, PIN 11
Keysense
PINK (-)
KEY SWITCH BLUE 7 PIN CONN, PIN 7
Immobilizer Data Bus
GRAY
IGNITION SWITCH WHITE 7 PIN CONN, PIN 6
Immobilizer Type
-
TRANSPONDER - SEE DIAGRAM #239
KEYLESS ENTRY CONTROL
Lock
GREEN (-)
DRIVER DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 24 #201
Unlock
PINK (-)
DRIVER DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 25 #201
Driver Door Unlock
YELLOW
DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 19
Trunk Release
ORANGE (REVERSE POLARITY)
DASH FUSE BOX GREEN 44 PIN CONN, PIN 43 #232
LIGHTING
Parking Lamp (+)
RED
DASH FUSE BOX GREEN 44 PIN CONN, PIN 31
Parking Lamp (-)
GRAY
HEADLIGHT SWITCH WHITE 12 PIN CONN, PIN 8
Headlights
YELLOW (-)
HEADLIGHT SWITCH WHITE 12 PIN CONN, PIN 7
Reverse Light
ORANGE OR TAN (+)
DASH FUSE BOX GREEN 44 PIN CONN, PIN 38
SECURITY
Horn
LT BLUE TO ORANGE (-)
DASH FUSE BOX GREEN 36 PIN CONN, PIN 32
OEM Alarm Arm
VIOLET (LOCK) BLUE (LOCK DETECT) (-)
DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 17 (LOCK) PIN 22 (LOCK DETECT)
OEM Alarm Disarm
RED (UNLOCK) LT BLUE (UNLOCK DETECT) (-)
DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 16 (UNLOCK) PIN 23 (UNLOCK DETECT)
All Door Trigger / Dome Light
PINK (-)
BACK OF DASH FUSE BOX 13 PIN CONN, PIN 11
Driver's Front Door Pin
BROWN (-)
DASH FUSE BOX GREEN 44 PIN CONN, PIN 6
Pass Front Door Pin
LT GREEN (-)
BACK OF DASH FUSE BOX GREEN 18 PIN CONN, PIN 11
Driver's Rear Door Pin
LT GREEN (-)
DASH FUSE BOX GREEN 44 PIN CONN, PIN 7
Pass Rear Door Pin
YELLOW (-)
BACK OF DASH FUSE BOX GREEN 18 PIN CONN, PIN 12
Trunk Pin
WHITE (-)
DASH FUSE BOX GREEN 44 PIN CONN, PIN 30
Hood Pin
BLUE (-)
DASH FUSE BOX GREEN 36 PIN CONN, PIN 4
CAN Bus High
PINK
IGNITION SWITCH WHITE 7 PIN CONN, PIN 4
CAN Bus Low
BLUE
IGNITION SWITCH WHITE 7 PIN CONN, PIN 3
OEM KEYLESS INTEGRATION
Lock Motor
ORANGE
DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 18
Driver Unlock Motor
YELLOW
DOOR HARNESS IN DRIVER KICK PANEL WHITE 25 PIN CONN, PIN 19
All Unlock Motor
RED
BACK OF DASH FUSE BOX GREEN 18 PIN CONN, PIN 18
Trunk Release Detection
ORANGE
DASH FUSE BOX GREEN 44 PIN CONN, PIN 43
OEM Keyless Module Location
-
OEM Lock Relay Location
-
ACCESSORIES
Window Up
D\ YELLOW P\ RED D\ LT GREEN P\ PINK @ MAIN SWITCH
Window Down
F/ GREEN F/ YELLOW R/ YELLOW R/ BROWN #211
How do I contact you
After removing the alarm, will the key fob still unlock and lock the doors?
I want to know this question to. Will your fob still work?
@@ernieperea9961 answer NO
answer NO
Hello Great Video ( Would it be ok to ask a question )?
I have a 2001 dodge neon with a dei 522t, remote start with a transponder 5UU something like that, not sure the model.. Anyway the alarm has been going off by itself a lot, so I unplugged all the wires going into the 522t remote start, I also took 2 fuses that where in 2 wire hardness,.. The strange thing is the alarm still goes off once in awhile, what could be causing this, and is there anything I can do?? Please Help..
I don't mind if the headlights flash, it's the horn honking, that are driving my neighbors nuts, and I been unplugging my battery every night..
is it a siren or a factory horn sounding off?
No siren is installed, it's the factory horn.. when it goes off the head lights flash and horn honks.. also when it was acting some what normal, the remote wouldn't disarm the alarm, with new battery installed in remote, the only way to turn off was to unlock the drivers door..
Thanks for the reply.
thats the darn factory alarm, not the aftremarket one. what you can do to fix that is open the driver door and while its open unlock the door with the key 2x
Thanks so much, I didn't know this car had a factory alarm.. after some googling I found other people with the same problem.. I just figured that what was under the dash was the problem.. Now I know all I have to do is lock the door manually when getting out..
But I would have never found this info, if not for you, Thanks so much, from the whole neighbor hood..
I think I'll disconnect my battery before I start cutting cables!
😂