Wo depend karta hai uske structure ke upor. Agar weld karne ka jaga hai aur magnet ka operation ke upor iska koi asar nehi parta to kor sakte hai. Thank you.
Good question. Many reasons may be there, few of them are below- 1. Starting belt tension of conveyor if more than belt permissible limit. 2. If pulley diameter is less than belt recommended diameter then breaking stress in belt will be more. 3. If transition distance (flat to full tough) is less than belt recommended distance then belt edges will get damage soon due to uneven load distribution across belt width. 4. Wrong selection of belt without considering filling factor, tough angle, number of ply, etc. 5. Wrong design of conveyor or conveyor components such as off centre loading of material on belt, any sharp edge coming in contact of belt, etc. Thank you. If you really enjoyed my channel video, please subscribe and share with others
We have same one , but we have problem is settled to work in 3 position it depends on material coming,when it work on 1 st position we have no problem but when it's work with the second and the third position it's work for 5mn and stop (contactor opens) what do you think it's the problem please? 😊
Sorry, I can't understand your question. Which 3 position you are talking about? If magnetic separator belt speed during operation (after catching heavy iron particle), may be motor is under designed. Please contact your supplier. Thank you
Good question. Magnetic separator is the transformation of electric energy into magnetic/mechanical energy. During the transformation some energy wastes as heart and temperature rises. There are mainly two ways to get solution, natural cooling or forced cooling depends on the design of magnetic separator. Thank you
Magnetic separator is applicable only for ferromagnetic materials like iron, nickel, cobalt and their alloys. Not applicable for silver, copper, etc. non ferrous metal. For non ferrous metal, you can use metal detector. Metal detector will detect metal and then mark the spot and as per logic can stop the conveyor. Then manually that metal needs to be removed from marked area. Hope i answer your question,, thanks.
Many reasons may be there, few of them are- 1. Misalignment of idler with respect to conveyor belt. 2. Design fault of idler. 3. Poor quality breathing. 4. Lack of lubrication. 5. Idler center to center distance more than recommended. Etc. Thank you
you have to keep some portion screw conveyor open where the magnetic separator to be installed and material of construction screw conveyor should also be non magnetic. However, prefer to installed magnetic separator before feeding to screw conveyor or after discharge of screw conveyor. thanks for your comment
It depends on the design of magnetic separator. If you place your requirement (weight to catch up and size, conv belt width, conv capacity, material depth, belt speed, carrying material details, etc) to OEM, they will design accordingly. thanks
Thank you for your question. actually gap depend upon many factors such as magnet strength, belt speed, burden depth/material depth on belt, particle size to be separated, etc. etc. Magnetic separator OEM will decide the gap needed during their engineering.
Actually I am not in manufacturing field (slurry handling). You please contact vendors who provide such solution. Many vendors are there, may be Linux magnetics, magnattack, etc. Thanks
Thank you for your comment. Sorry, at this moment I don't have any handy sketch of the method. You can ask any magnetic separator vendor for that or Google it please. I have a plan, to put all information in a website in future. Please subscribe my channel and share the video with others. Thanks again.
I don't know how to answer your question. There are dedicated company who makes magnetic separator. Actually making of magnetic separator needs lots of calculation and datas. Basically magnetic separator mainly has magnet, belt, geared motor and many other items. Hope, i am able to answer your question. Thank you for your question.
Thanks for your query. Actually required gauss rating depends on many factors. Few of them are conveyor belt speed, carrying material properties, carrying material depth on conveyor belt, height of hanging magnet from conveyor belt, what is the maximum weight of tramp iron to separate or lift, environment, etc. For medium intensity equipment It may start from 400 at a distance of 200mm.
@@amiteshranjan1345 Sorry, i can't understand your question. Sand hopper for what purpose, conveyor carrying sand and the hopper for sand feeding to conveyor? will you please elaborate ?
@@amiteshranjan1345 followings are the general practices for feeding material to belt conveyor- 1. If feed hopper is large in capacity, should use any feeder below hopper (between hopper and belt) to feed material to belt conveyor. It will help easy extraction of material from hopper and eliminate column load on conveyor belt due to material height in hopper. If all material falls on conveyor belt at a time (for high capacity hopper), the conveyor will stop working due to sudden high load on belt. 2. Material from high capacity hopper may be feeded to conveyor belt directly without using any feeder (like sand carrying ship), but the feeding should be in controlled way (small small material should fall on belt at at time) otherwise belt will stop. 3.. If the capacity of hopper is low with respect to conveyor, direct feeding in conveyor may be allowed without using any feeder. In that case belt should be designed considering that column load of material. 4. If there is feeder below hopper or in case of small capacity hopper without feeder, there should be skirt board on belt to receive material. 5. If you want to feed material directly from hopper to belt conveyor through chute and are not using any skirt (though, this is not recommended), then chute height and cross-sectional dimension will depend on belt conveyor design parameters. Material weight in chute must not be beyond conveyor design capacity, otherwise conveyor will not work. Those all (conveyor feeding mechanism and system design) are vast subject and very tough to explain in short write-up. However, hope you will get some idea regarding that. Thank you
Thank you for your question. If you look closely, one belt is running all around the magnet. iron particle is attracted by magnet and stuck with belt, the belt bring the particle out of magnetic zone where particle falls freely..
![[Full] 4 ต่อ 4 Celebrity EP.920 | 3 พ.ย. 67 | one31](http://i.ytimg.com/vi/KwiW2M_kAg4/mqdefault.jpg)
which is the best company for magnetic separator for conveyors
Elektromag. Eriez
Hope you would prepare and share other items ( sampling unit , trippers, crusher , vibrating feeders and more ).Thank you.
Thanks for your comment. I will. Few shots are there in my channel, you can try. 👍
Thanks for actual work video
You are welcome. Please subscribe my channel and share with others
Form Lawrence Massachusetts god bless all of us amen 🇩🇴🇩🇴🇩🇴🇩🇴🇩🇴🙏🙏🙏🙏🙏🙏Form Lawrence Massachusetts god bless all of us amen 🇩🇴🇩🇴🇩🇴🇩🇴🇩🇴🙏🙏🙏🙏🙏🙏
👍
Kya suspended magnet ke base mein 4 legs weld kar sakte hai
Wo depend karta hai uske structure ke upor. Agar weld karne ka jaga hai aur magnet ka operation ke upor iska koi asar nehi parta to kor sakte hai. Thank you.
Sir any 2 reasons why belt break during running time??
Good question. Many reasons may be there, few of them are below-
1. Starting belt tension of conveyor if more than belt permissible limit.
2. If pulley diameter is less than belt recommended diameter then breaking stress in belt will be more.
3. If transition distance (flat to full tough) is less than belt recommended distance then belt edges will get damage soon due to uneven load distribution across belt width.
4. Wrong selection of belt without considering filling factor, tough angle, number of ply, etc.
5. Wrong design of conveyor or conveyor components such as off centre loading of material on belt, any sharp edge coming in contact of belt, etc.
Thank you. If you really enjoyed my channel video, please subscribe and share with others
We have same one , but we have problem is settled to work in 3 position it depends on material coming,when it work on 1 st position we have no problem but when it's work with the second and the third position it's work for 5mn and stop (contactor opens) what do you think it's the problem please? 😊
Sorry, I can't understand your question. Which 3 position you are talking about? If magnetic separator belt speed during operation (after catching heavy iron particle), may be motor is under designed. Please contact your supplier. Thank you
Reasons for magnetic seaparator temperature rise,any soloution to avoid it
Good question. Magnetic separator is the transformation of electric energy into magnetic/mechanical energy. During the transformation some energy wastes as heart and temperature rises. There are mainly two ways to get solution, natural cooling or forced cooling depends on the design of magnetic separator. Thank you
Magnetic sapreater remove iron particles only? If any silver or copper particles how remove this ?
Magnetic separator is applicable only for ferromagnetic materials like iron, nickel, cobalt and their alloys. Not applicable for silver, copper, etc. non ferrous metal. For non ferrous metal, you can use metal detector. Metal detector will detect metal and then mark the spot and as per logic can stop the conveyor. Then manually that metal needs to be removed from marked area. Hope i answer your question,, thanks.
Sir what r the reasons for carrying roller and return roller makes abnormal sound??
Many reasons may be there, few of them are-
1. Misalignment of idler with respect to conveyor belt.
2. Design fault of idler.
3. Poor quality breathing.
4. Lack of lubrication.
5. Idler center to center distance more than recommended.
Etc. Thank you
Can this work fine on a close screw conveyor carrying solid materials like cashew shell or canel shell.
you have to keep some portion screw conveyor open where the magnetic separator to be installed and material of construction screw conveyor should also be non magnetic. However, prefer to installed magnetic separator before feeding to screw conveyor or after discharge of screw conveyor. thanks for your comment
Which type magnetic brother
Electro magnet
Hello sir can you reply me how much weight it will catch up
It depends on the design of magnetic separator. If you place your requirement (weight to catch up and size, conv belt width, conv capacity, material depth, belt speed, carrying material details, etc) to OEM, they will design accordingly. thanks
how much gap maintain between belt conveyor and obms in not hanging type in cross magnetic separator
Thank you for your question. actually gap depend upon many factors such as magnet strength, belt speed, burden depth/material depth on belt, particle size to be separated, etc. etc. Magnetic separator OEM will decide the gap needed during their engineering.
we need to detect MS parts in Graphite slug ( Semi solid slug ) before feeding it to Hopper of an Extruder. kindly suggest suitable method for this.
Actually I am not in manufacturing field (slurry handling). You please contact vendors who provide such solution. Many vendors are there, may be Linux magnetics, magnattack, etc. Thanks
Thanks for sharing a practical field video. I need a complete sketch of the method. How can I get it?
Thank you for your comment. Sorry, at this moment I don't have any handy sketch of the method. You can ask any magnetic separator vendor for that or Google it please. I have a plan, to put all information in a website in future. Please subscribe my channel and share the video with others. Thanks again.
Please what the right magnet to use for conveyor the distance between magnet and conveyor is 15 cm
Hello, get 【price & details 】about 【magnetic separator 】please click web:
www.sinofote.com/cp/magnetic_separator.html?zlY2
If you like, you can join my facebook group and share your products there also. below is the link- facebook.com/groups/208491943526317
we supply magnetic separator, welcome to click here to get price:
www.ore-processingplant.com/products/magnetic-separator.html?cc
How to make the magnetic separator belt ?
I don't know how to answer your question. There are dedicated company who makes magnetic separator. Actually making of magnetic separator needs lots of calculation and datas. Basically magnetic separator mainly has magnet, belt, geared motor and many other items. Hope, i am able to answer your question. Thank you for your question.
Thanks for great explaining
You are most welcome. Please subscribe my channel and share the video with others also
Esko supply kitna aur kaise connection karte hai
Yeh to machine to machine varry karta hai. Machine banane wala bata payega uska specification ke hisab se
Why ss angle is used in magnetic separator
Which SS angle your are talking about? SS is non magnetic that is why used. But which angle you are talking about. Thanks
What should be the GAUSS RATING of this permanent magnet
Thanks for your query. Actually required gauss rating depends on many factors. Few of them are conveyor belt speed, carrying material properties, carrying material depth on conveyor belt, height of hanging magnet from conveyor belt, what is the maximum weight of tramp iron to separate or lift, environment, etc. For medium intensity equipment It may start from 400 at a distance of 200mm.
Working principle?
I will upload separate video on working principle later. Thank you
sir 2nd question how much minimum gap maitain between belt conveyor and sand hopper
Are you talking about sand hopper for metal detector or anything else ?
@@iamsajalchakraborty only sand not sand metal detector
@@amiteshranjan1345 Sorry, i can't understand your question. Sand hopper for what purpose, conveyor carrying sand and the hopper for sand feeding to conveyor? will you please elaborate ?
@@iamsajalchakraborty minimum gap between belt conveyor and sand hopper chute
@@amiteshranjan1345 followings are the general practices for feeding material to belt conveyor-
1. If feed hopper is large in capacity, should use any feeder below hopper (between hopper and belt) to feed material to belt conveyor. It will help easy extraction of material from hopper and eliminate column load on conveyor belt due to material height in hopper. If all material falls on conveyor belt at a time (for high capacity hopper), the conveyor will stop working due to sudden high load on belt.
2. Material from high capacity hopper may be feeded to conveyor belt directly without using any feeder (like sand carrying ship), but the feeding should be in controlled way (small small material should fall on belt at at time) otherwise belt will stop.
3.. If the capacity of hopper is low with respect to conveyor, direct feeding in conveyor may be allowed without using any feeder. In that case belt should be designed considering that column load of material.
4. If there is feeder below hopper or in case of small capacity hopper without feeder, there should be skirt board on belt to receive material.
5. If you want to feed material directly from hopper to belt conveyor through chute and are not using any skirt (though, this is not recommended), then chute height and cross-sectional dimension will depend on belt conveyor design parameters. Material weight in chute must not be beyond conveyor design capacity, otherwise conveyor will not work.
Those all (conveyor feeding mechanism and system design) are vast subject and very tough to explain in short write-up. However, hope you will get some idea regarding that. Thank you
How can i by
Many vendors are there who sell magnetic separators such as electromag, eriz, etc. please Google and contact them. Thank you
How iron particle is removed from the magnet
Thank you for your question. If you look closely, one belt is running all around the magnet. iron particle is attracted by magnet and stuck with belt, the belt bring the particle out of magnetic zone where particle falls freely..
please share magnet struvture used in mag separator
Sorry, can't understand your comment (magnet structure)
Hello, get 【price & details 】about 【magnetic separator 】please click web:
www.sinofote.com/cp/magnetic_separator.html?zlY
Why step for start magnetic exitacion from manual local
Sorry, unable to understand your comment. Will you please elaborate a bit?
Untuk spesifikasi detail mesin & HARGA mesin Magnetic separator tersebut:
Mohon Hubungi
VALTEKINDO
Terimakasih
Sorry, unable to understand your comment. Will you please write in English. Thank you
Please send make cross belt magnetic seperator
Exactly I can't remember the make. But many good manufacturer are here in India, few of them are Electro flux, Electro magnetic industries. Thank you
Thanks !
Welcome
We are a profesional manufacturer of magnetic separator. Contact me if you have needs.
How to control belt side going
Pl share your contact details
iamsajalchakraborty@gmail.com
That can be controlled by tracking belt and adjusting idlers and pulleys. Thanks
Sure. Thanks