1 more tip I will give you all is only if you have frozen plastic or whatever it is cube so its not UV coated go outside with the cube and do like 5 solves then go back in and make sure its quite cold like -1 degrees or alternative freezer or refrigerator but this is a lengthy process, put in refrigerator for like 2m and do a solve and repeat till its nice however I do recommend cleaning it once in a while since you can get hairs, lube, and even dust inside ur cube my Gan 12 was slowing down after some time from factory mods, but once outside for a bit I came home and it was like brand new and it might not work so effectively with springs but it will work 100% with MagLev (I have 2nd Tightest Setting)
reasons for why this wont work for logner periods of time if u just clean it it will eventually get slow again bec u put water into it and once it dries out its just creating more friction I fugred out the hard way, on my moyu 2019 and had to remove the springs entirely to make it at least half decent there are a lot of substitutes like dish soap but they wont last long, by dish soap I mean you have to have it submerged in water a bit so its like water lube, but it wont create the layer like silicone lubes will and will eventually dry off easily or just will feel insanely bad to turn I just recommend either making ur own lube or buying since bro gan 1 lube aint that bad for its price or traxxas 50k they're both really cheap lubes.
0:22 Just so you know you should never pull the corner of the cube out first instead you with turn the top layer 45 degrees and pull out the edge part same goes with assembling the cube as it will be easier and wont damage the cube
You don't have to sort the pieces, it helps to assemble the cube after cleaning. I sorted the dirty and clean pieces and then sorted the clean pieces into edge, corner, and center pieces. If it is hard for you to disassemble the cube, remove one of the center caps, and loosen the screw.
Bhai mere mere aapke pass kahin ki cube hai to aap mere ko ek giveaway kar dijiye free mein mere ko kyon sikhana hai vah mere pass bekar wala hai bahut hi Piche Piche rahata Hai de dijiye free mein
@@Akroast9712 You can but you can't fully remove all the dust. If it's hard for you to disassemble it, remove one of the center caps and loosen the screw.
Main ne is video ko dhekne ke baad jo step app ne bataya tha oos follow karne baad mera cube aur jyada kharab ho gaya bakwas video 😵💫😵💫😵💫😵💫😵💫💯😵💫💯👎🏼👎👎👎👎👎
1 more tip I will give you all is only if you have frozen plastic or whatever it is cube so its not UV coated
go outside with the cube and do like 5 solves then go back in and make sure its quite cold like -1 degrees
or alternative freezer or refrigerator but this is a lengthy process, put in refrigerator for like 2m and do a solve and repeat till its nice
however I do recommend cleaning it once in a while since you can get hairs, lube, and even dust inside ur cube
my Gan 12 was slowing down after some time from factory mods, but once outside for a bit I came home and it was like brand new and it might not work so effectively with springs but it will work 100% with MagLev (I have 2nd Tightest Setting)
timestamps:
0:00 Introduction
0:10 Step 1 De-assemble the cube
1:01 Step 2 Sort the pieces
1:35 Step 3 Cleaning the cube
3:17 Step 4 Re-assemble the cube
5:19 Step 5 Last Layer
:)
@@ultimate6194 Never thought I'd get timestamps on my videos. Thanks
@@TheTwistedCuberyou’re welcome
What you use to clean cube?@@TheTwistedCuber
@@PoonamRajput-b4c Tissue🤣🤣
0:10 You know you can loosen the hub bolts, right?
@TheVoidStudioOfficial I did not know that until a few months ago
i just have another tip. If you have QiYi warrior cube just loose one of the screws a little bit.
Yeah, I was about to make a video on it, but it works on almost every other cube. For GAN cube, use the GES tool.
Cleaning the cube actually helps. This is a great video ❤
Thanks
Cleaning the cube makes it feel like sand.
It smells like sand
Taste like sand
It's probably a sand.
reasons for why this wont work for logner periods of time
if u just clean it it will eventually get slow again bec u put water into it and once it dries out its just creating more friction I fugred out the hard way, on my moyu 2019 and had to remove the springs entirely to make it at least half decent
there are a lot of substitutes like dish soap but they wont last long, by dish soap I mean you have to have it submerged in water a bit so its like water lube, but it wont create the layer like silicone lubes will and will eventually dry off easily or just will feel insanely bad to turn
I just recommend either making ur own lube or buying since bro gan 1 lube aint that bad for its price or traxxas 50k they're both really cheap lubes.
I think I made a mistake, it's probably better to clean it without adding water to the cloth.
I mean adding water to the cube itself not the cloth
I am ur 667. Subscriber!
0:22 Just so you know you should never pull the corner of the cube out first instead you with turn the top layer 45 degrees and pull out the edge part same goes with assembling the cube as it will be easier and wont damage the cube
does putting the cube underwater then scrambling it and solving it in the water work?
well there is one way to find out..
@@muffindg5780 it didnt):, it rusted it instead
@@GivingOthersAMentalBreakdown u have sacrifised ur self for the others :)
I can feel the pain putting the last layer
Bro its easy when you have MagLev
I also
@@RealRenko And easy when you have springs on cube
You can also loosen the screws to make it easier to disassemble
That one last corner is a pain
It's a GREAT video, and that's no exaggeration.
Thanks
thanks for helping me to make my cube smoother also by cleaning
Wooooo
@@mansibhovad4532 Woooooo
I watched the whole tutorial and found you dont need to take the centerter off of the last layer.
How much is your cube
10$
What!😳
@@TheTwistedCuber mine is 1$
@@TheTwistedCuber and it's smooth
@@craftworld123 where did you buy it from?
Do i only need to loosen one screw or all screws to make the cube faster
All of them. Also, if you loosen it too much, your whole cube could break.
@@TheTwistedCuber ok thanks
I always do that but I can't seem to get it perfectly
This actually works, thx Bro :)
You can use lube if you want to make it even more faster.
Oil? I once tried it and it turnd to micropieces like sand in little time, so I didnt try again.
Oil is bad because it will be good for a few weeks, then it will be trash
Aur bhai kaun sa Tel dalen jismein Mera Kyon badhiya Ho Jo Mere Pass leave Nahin Hai
Bhai abi ky time per konsa tarika best hai konsa oil lagna chaye taky bad ma karab na ho
You can use any oil. I didn't use oil in this video because the title says "How to make your cube faster and smoother without lube or oil"
@@TheTwistedCuber mera matlab kia kia hum use kary jo bad ma slow na ho
@@LizazEnglish Coconut oil
Heyy,so i was just wondering we sort the pieces according to what? And i find it difficult to de-assemble the cube
You don't have to sort the pieces, it helps to assemble the cube after cleaning. I sorted the dirty and clean pieces and then sorted the clean pieces into edge, corner, and center pieces. If it is hard for you to disassemble the cube, remove one of the center caps, and loosen the screw.
@@TheTwistedCuberthank u so much!!
i fell bros pressure on the first part
If don't mind don't hardly pull out the pieces just unscrew it
I learned that you can loosen the screws to make it easier two months later.
@@TheTwistedCuber kehna kya chate hoooooo
This was a great video.But by mistake I turned the screw on the wrong side and my cube is rip now
ok this could actually work since there's dried Thinner in my cube-
I don't recommend taking all parts cause it' will more slow the cube
What is rate of your rubiks cube
800 rupees
i learned one more thing that how loose the screw is so smooth the cube
Super easy I'll try it rn
Bhai machine ka tel Dal sakte hain
@Zishanmath If you put oil in your cube, no matter which oil it is, it will be fast for a few days and then gradually get slower.
I have a problem. I have put kitchen oil in my kube and i though it Will go much faster but now is it so slow. What should i do? 😢
Dissasemble the cube and try to remove the oil with water and a cloth.
Thanks for a Quick answer. I Will try it 😊
What is this song name ?
I know this song looks familiar
But idk it's name
@@mervatmakram3111 ON AND ON(CARTOON)
That cube looks so similar to my cube it might be the same
Lots of cubes look the same
just clean the cube, that's what took him 10 minutes to teach
That is the MoYu new cube, I am using it Gan 14 is my main
@allenzhang5223 This video is 2 years old 😭😭
What you using for cleaning
I used tissue paper, you can use a cloth too
My cube was only 80 cent and i do it and i got my cube like flash dam 😂😅
Thanks
I cant de assemble my cube its so hard
Bro
If it is hard for you to disassemble the cube, remove one of the center caps, and loosen the screw
Bhai mere mere aapke pass kahin ki cube hai to aap mere ko ek giveaway kar dijiye free mein mere ko kyon sikhana hai vah mere pass bekar wala hai bahut hi Piche Piche rahata Hai de dijiye free mein
@@Zishanmath Bhai mere pass paisa nahi hai 😭😭😭😭😭
Mai cube ko aap tak kaise pahunchaoonga😭😭😭😭😭
This is worst video no use for cleaning it just looks neat but no use we need to add lube, loose screws and adjust magnet power
The methods you said also work, but cleaning your cube also makes your cube much faster because dirt can pile up in your cube and make it slower.
I'm do that but it still not fast and smooth
Loosen the screws in your cube
Simple ways is sprinkle some (white)flour inside the cube and verify it
It is not recommended because your cube will be good for a few days, and then it will start to slow down.
Better trick loose the cube and it made very smooth
Hii😊
Their was hair in my cube 😂
that ad?! just clen the cube?!
?
It's the moyu mei long
Oh its my patent 😅
❤
Hiii
its moyu melilong 3c
I use Gan
Time waste video
499₹ cube I have
No clue
?
For me it makes the cube slower😢
It will make it slower if you had put oil or lube in it
I threw it
@@shitaldeore3259 Nice
Nariyal ka tel lagao moj manao
Maine try Kiya tha but faster nahi more slow ho gaya khane ka tel lagao use speed hota hai dont use nariyal ka tel
@@Pro_EDITX_95 It will be faster for a few days, then it will be very slow
@@TheTwistedCuberCan we clean cube without disassembling it ? By just cleaning in gaps?
@@Akroast9712 You can but you can't fully remove all the dust. If it's hard for you to disassemble it, remove one of the center caps and loosen the screw.
noob 😂😂😂
What
???
It really works😊
Main ne is video ko dhekne ke baad jo step app ne bataya tha oos follow karne baad mera cube aur jyada kharab ho gaya bakwas video 😵💫😵💫😵💫😵💫😵💫💯😵💫💯👎🏼👎👎👎👎👎
Did you put oil in your cube?
Pagal