O meu roborock S50 está com esse mesmo erro de carregamento. Parabéns pelo esforço na solução, mas precisa de muitas ferramentas e técnica pra fazê-la.
I went into this with no soldering experience. When I took the bad fuse off, there were two reddish rectangles underneath. Are those solder pads? I removed those too and there was a metallic material underneath the red rectangles. Was the new fuse supposed to be soldered to those red pads?
Hi, what tools do you use on your wideo? How do you so easily separated the the fuse from the motherboard? I’m rather inexperienced in that matter and looking for some advice.
Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard? Thx in advance!
I was able to fix it, finally! I replaced the capacitor on the charging dock but didn't fix it. Then changed the fuse as shown in this video and that worked like a charm
Measured the resistor and it shows 0.15-0.4 values. Jumped it with a wire just to be sure....stil have the same error...any help? Battery ang charging station measures where ok. Also switched the battery Frome and with a friend's robot and his work fine with both of them, mine gets the error 13 with both ones
I first changed the capacitor on the charging station but that doesn't do anything, and after that i did what you did which was quiet a hussle (used another brand of a resettable fuse) and it the robot is finally charging again
@@TechDayEveryDay with what device? And what is the liquid? And isn't there some danger because of the hot air and the parts close to the fuse which should not get broken?
Hi I also have a error 13 problem with my robot. But mine charges. Once the robot is charged and i try to start it it just turns off. Once it restarts it starts to charge again. I tried a known good battery but the problem still prevailed. I also jumped the fuse on the Mainboard but it did not held. What could I try now?
![[EN] Roborock S50 - Error 13 - mainboard fuse exchange](http://i.ytimg.com/vi/CGj-sO4wKOU/mqdefault.jpg)
![[Live สด] การออกรางวัลสลากกินแบ่งรัฐบาล งวดวันที่ 16 พฤศจิกายน 2567](http://i.ytimg.com/vi/wPd7VFfWHIA/mqdefault.jpg)
O meu roborock S50 está com esse mesmo erro de carregamento.
Parabéns pelo esforço na solução, mas precisa de muitas ferramentas e técnica pra fazê-la.
In my S50, fixed the charging error by changing the main capacitor in the charger. 10 minute job.
I done the same, but error returns after 3 month
This fixed the Error 13 on my Roborock E25, thanks!
You are welcome;)
Yessss it works. Thanks for sharing my roborock is back!
You are welcome
I went into this with no soldering experience. When I took the bad fuse off, there were two reddish rectangles underneath. Are those solder pads? I removed those too and there was a metallic material underneath the red rectangles. Was the new fuse supposed to be soldered to those red pads?
Hi, what tools do you use on your wideo? How do you so easily separated the the fuse from the motherboard? I’m rather inexperienced in that matter and looking for some advice.
Dziękuję Robrock s55 śmiga teraz super :)
Proszę bardzo :)
Gdzie kupiłeś bezpiecznik?
W TME
Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard?
Thx in advance!
Were you able to fix it? My S5 is driving me crazy
I was able to fix it, finally! I replaced the capacitor on the charging dock but didn't fix it. Then changed the fuse as shown in this video and that worked like a charm
What is the liquid that you put on the bad fuse to take it out?
Flux?
Measured the resistor and it shows 0.15-0.4 values. Jumped it with a wire just to be sure....stil have the same error...any help?
Battery ang charging station measures where ok. Also switched the battery Frome and with a friend's robot and his work fine with both of them, mine gets the error 13 with both ones
Where do you get a fuzz like this? How Do I know if it applies to the s7?
Nice job, thanks for explanation 👍🏻✌🏻
I first changed the capacitor on the charging station but that doesn't do anything, and after that i did what you did which was quiet a hussle (used another brand of a resettable fuse) and it the robot is finally charging again
It is nice to hear that it helped you.
После замены предохранителя отказался пылесос заряжаться и видеть заряд докстанции..
Причём тестого собирал, всё ок..собрал полностью и кирдык
Moin, ich habe das selbe Problem wo kann ich so eine Sicherung bekommen? Gibts irgendwo auch einen Schaltplan?!
May I ask where did you get the replacement fuse in the US? Thanks!
Hi, temp of the air flow?
it works thanks !!!
I changed the whole motherboard and that didn't solve my problem, so i changed the charging base and then yes that was definitely solved
What are you using there to get of the old fuse?
I'm using hot air.
@@TechDayEveryDay with what device? And what is the liquid?
And isn't there some danger because of the hot air and the parts close to the fuse which should not get broken?
@schr3ck3 please check link from below www.google.com/amp/s/www.instructables.com/SMD-SOLDERING-101-USING-HOT-PLATE-HOT-AIR-BLOWER-S/%3famp_page=true
Unfortunately that didn't fix it. will keep looking!
Try to change capacitor into dock station. There are videos about it
@@spoloborota2 yup, I did it a while back and it fixed it
Hi I also have a error 13 problem with my robot. But mine charges. Once the robot is charged and i try to start it it just turns off. Once it restarts it starts to charge again. I tried a known good battery but the problem still prevailed. I also jumped the fuse on the Mainboard but it did not held. What could I try now?
i have the same problem. have u solved ur problem?
My dad called it suckerbot 2000
I have that!!!!