To service the electronics or condensate pump we need to access the right side of the unit (when viewed from output vent). But the soffit shown at the end of the video appears to show the right side of the unit up against a wall making it inaccessible for service. Can you show us photos of a correctly installed unit with soffit and access panel? Thanks.
Hello, My High wall Duct-Free units display the "Set" temp for the unit on the front panel. If I toggle the remote,the front display will read the Room Temperature BUT only for a few seconds before reverting back to the Set temp. Question, Is there a way I can set the front panel to display the current room temperature without reverting back to the set temp? Thank you in advance
This video shows the what appears to be the wrong flaring tool for a unit with the heat pump feature. The tool used in this video appears to be a "Concentric" and does not flare copper tubing in a manner intended for the high pressure associated with heat pump mode. The proper flaring tool has an "Eccentric" design and flares tubbing in a manner suited to substantially higher pressure.
So what happens if the condensate pump fails? How difficult is replacing the pump? Asking seriously because I'm strongly considering one of these but I am not crazy about how these handle condensate.
Hello Jeremey - thanks for checking with us. It is recommended that an access panel be installed under the unit to provide access if service is needed. We hope this helps! -NC
Hello Jose, thanks for your interest in our exciting new our High ESP Duct unit, which has a built in condensate pump and associated float switch that manages the operation of the condensate pump. I hope this helps! -SF
Where can I buy the threaded rod parts? I can't seem to find it online or in my local hardware store. What size threaded rod is used? What type of vibration dampening parts are used?
Hello Metz - thanks for checking with us! We do not have the model number of the actual unit in this video published in Jan. 2016. Please check our website below for current FlexFit models which include the Slim Duct design: www.haierductless.com/series/flexfit-single-zone-series FlexFit Slim Duct models are available in 7,000 BTU, 9,000 BTU, 12,000 BTU or 18,000 BTU. We hope this helps!
This department assists with appliances in the United States, but we certainly have support available for our consumers in Australia as well. You can view support information at this link: spklr.io/6051S7GT . We're confident those specialists will be able to help!
![CAMPปลิ้น | EP.79[1/2] แก๊งไทบ้านพาบุกเมืองบั้งไฟโก้ ยโสธรรรร!!!](http://i.ytimg.com/vi/Ldr3_fvTEXk/mqdefault.jpg)
To service the electronics or condensate pump we need to access the right side of the unit (when viewed from output vent). But the soffit shown at the end of the video appears to show the right side of the unit up against a wall making it inaccessible for service. Can you show us photos of a correctly installed unit with soffit and access panel? Thanks.
Can you add a plenum ti this unit and run 3 ducts about 7 feet?
Hello,
My High wall Duct-Free units display the "Set" temp for the unit on the front panel.
If I toggle the remote,the front display will read the Room Temperature BUT only for a few seconds before reverting back to the Set temp.
Question,
Is there a way I can set the front panel to display the current room temperature without reverting back to the set temp?
Thank you in advance
This video shows the what appears to be the wrong flaring tool for a unit with the heat pump feature. The tool used in this video appears to be a "Concentric" and does not flare copper tubing in a manner intended for the high pressure associated with heat pump mode. The proper flaring tool has an "Eccentric" design and flares tubbing in a manner suited to substantially higher pressure.
great, thanks a lot
So what happens if the condensate pump fails? How difficult is replacing the pump? Asking seriously because I'm strongly considering one of these but I am not crazy about how these handle condensate.
you fix it when you're making the repair on the sheetrock.
I have a problem with this system, the ducts stopped sending air into the space, the efficiency is very low
Nice installation video, please can I get this video?
If you install that in a soffit how can it be serviced or repaired in the future without tearing out sheet-rock every time?
Hello Jeremey - thanks for checking with us. It is recommended that an access panel be installed under the unit to provide access if service is needed. We hope this helps! -NC
Muy buenos
where can i get those long bolts with the bracket to purchase to hang my unit?
It's called all thread and comes in 10' lengths. It is cut to size in the field.
Thank u so much
You are welcome, Islow!
Could you tell me what is the name or code of the optional drain pump ? Thanks in advance
Hello Jose, thanks for your interest in our exciting new our High ESP Duct unit, which has a built in condensate pump and associated float switch that manages the operation of the condensate pump. I hope this helps! -SF
please, i need help asap. :(
Sir three phase wiring in pcb indoor & outdoor & main supply please sir
Hello Khan - are you located in the United States? What is the model number please?
Where can I buy the threaded rod parts? I can't seem to find it online or in my local hardware store. What size threaded rod is used? What type of vibration dampening parts are used?
3/8s rod and nuts.
I use vibration pads in between
Home depot sells it
I’m try find that parts but I can’t , do you know another place ?
@@thisguy333 What is the right-angle bracket called? I tried to search threaded rod hanger to no avail. Thank you.
Try ceiling mount cassette bracket
What size is this?
Hello Metz - thanks for checking with us! We do not have the model number of the actual unit in this video published in Jan. 2016. Please check our website below for current FlexFit models which include the Slim Duct design: www.haierductless.com/series/flexfit-single-zone-series
FlexFit Slim Duct models are available in 7,000 BTU, 9,000 BTU, 12,000 BTU or 18,000 BTU. We hope this helps!
جميل ❤
Ок
Hello do have spare parts PCB for model AD09SS1ERA in Australia?
This department assists with appliances in the United States, but we certainly have support available for our consumers in Australia as well. You can view support information at this link: spklr.io/6051S7GT . We're confident those specialists will be able to help!
Thanks..,
Sir
सर हिंदी में बताया करो
Kisi ka bhi chalega koi bhi ho
Hei am woRk thet
Not good.