￡130.26 5％ Off | 5GG 827 469 F For Vw Golf 7 Vii Mk7 Flip Badge Logo Rear View Camera 5GG827469F 5GG 827 469 F a.aliexpress.com/_mLvWWYX I picked the highline and that’s the video.
Your welcome let me know if you need anything else. I’d recommend buying the same camera as me if your planning to follow along some have a blue wire not covered in my vid
Both our cars, BMW X5 and Golf GTE, have reversing cameras. What I don't like about the VWs is that as soon as you take the car out of reverse, the camera cuts off. With the X5 the camera remains for a few additional seconds. So I still have a rear view as I edge forward.
Wouldn’t it have been easier to run cable through roof lining and front door pillar to fuse box ? About to attempt an install on my golf r . Found it easy to root cable for my rear dash camera that way 🤔
Hi there, Thanks for the video, as good as I've seen 👍🏻 What I'm not sure about still though is the two orange wires and the red wire up to the back of the MIB2 unit. I think the red goes to the fuse box? It's not clear what needs doing to the two yellow/orange ones? Thanks again, Mac
Go on the pins and match the colour stripes and you’ll be fine on the canbus connection. Red is the +12v it can go into the back of the fuse box but it’s a right pain. I used a fly wire type thing.
@@andygardner3177 Camera installed, however getting below error on long coding "marginal conditions have not been met" seems camera is new and do not have basic settings :/
@@kasten8020 Hard to say exactly what helped, but I was in dealership where they had ODIS ( official software ). They tried to code it but got the same error. Next day its simply started to work.
Hi Andy, great video! planning to take on the project myself for a 2019 eGolf (w/ Discover Media). I have a few quick questions.. Do you find the quality of the camera up to the standards of "OEM"/original? or do you think the OE camera from VW will be better quality? Regarding the wiring of this version (highline), there is no need to tap into the reverse light because of the canbus connection, right? My understanding is that there are just 2 canbus wire, 2 video wire, and a 12v power to connect at the back of the MIB unit. (Is there a ground as well?) Any tips on how to pick up the 12v power from the red wire without damaging the original wiring? Thanks!
Hi, The camera looks as good from a visual compare with a friend. You are correct with highline there is no feed from the light. The ground is taken from the car wiring you plug into in order to open the tailgate. The brown and purple connector shown in the video. You can take it put it into the fuse board but this is hard or use a fuse "piggy back"
@@andygardner3177 Thanks so much Andy, fuse "piggy back" sounds great! I guess for us UK cars we just run the wire on the left side and we can access radio and fuse box without wiring going through the middle?
Are you trying to use a piggy back/fly wire device or fitting the fuse way in? I have a 7.5AMP fuse in. I think i picked this size based on the factory wiring diagram so it's the same size as if car came with the camera.
Hi Andy, great video. Helped me a lot! Thank you for this. Just wanted to ask if you managed to make the video on coding and calibration? Would really love to do it myself. I have a vagcom
Great video! The most I have installed so far is the Dashcam, front and back, with connection to the fuse board. How hard is it to install the rear view cam? what tools do I need?
The connection to the back of the fuse board is a nightmare it’s really tight and you need to pull the purple retainers out of the back of the fuse board. I used a piggy back fly wire fuse thing. Tools wise it’s trim tools, trox bits, a socket for the rear seat and tape. I also used a bit of strong wire to help with pulling the cables. I taped the cable to the wire then pushed it thru.
@@andygardner3177 Hey Andy, thanks so much for your help. I fully agree with your approach. I saw some other videos but I don't know why they pull out the screen as well. It should be enough to get out the mib unit in the glove compartment. I sent you a Instagram connection request BTW 😊
Thanks for the video very useful! I am stuck with two orange/brown and orange purple cables that need to go in to the MIB but there was no can bus connector included in to my wiring loom set, do you know if it’s possible to connect them in a different way?
Hi, Did you have any issues of the display keeps disappearing and needing to do a hard reset on the main MiBII system? I see you have using the same 12v positive as the head unit did that work fine?
Hello, greetings from Spain. my camera shows error B201000. Does it mean that it is not parameterized? or what is missing to calibrate? Do you know if it can be done in obdeleven? or vagcom? Thank you
Hi my friend please I want to ask you, the higline reversing camera retrofit have 3 or 4 deferent mode of view, I want to ask those options of view into the camera or you need to change some unit on your car to get it?
My friend , I just want to know the options into the camera or the unit of the car , by the way install it in my car but I not have those mode of view the car seat Leon mk3 cupra, I am afraid 😟 my unit not have it that all if I have have to change the camera I will do it no problem 😊
Guten Tag, ich heute Kamera eingebaut in ein Versand t roc und das Problem das die Kamera nichts anzeigt.Könenen sie ein Video machen wie es codiert wird. Danke
Coding from: ilovecarmods.com/vw/composition-media-mib2 Module: 5F (Information electronics) Coding → Long Coding → Byte: 19 → Bit: 4 New value: disable Module: 5F (Information electronics) Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B New value: activated Module: 5F (Information electronics) Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B_msg_bus New value: Comfort data bus Module: 76 (Parking aid) Coding → Long Coding → Byte: 02 → Bit: 4 New value: enable Module: 19 (CAN getaway) Adaptation → Channel: Installation list; specified installations - Camera System Rear View New value: Coded Module: 6C (Rear view camera) Coding → Long Coding → Byte: 07 → Bit: 0 New value: enable Module: 6C (Rear view camera) Coding → Long Coding → Byte: 07 → Bit: 1 New value: enable Module: 6C (Rear view camera) Coding → Long Coding → Byte: 07 → Bit: 2 New value: enable Module: 6C (Rear view camera) Coding → Long Coding → Byte: 07 → Bit: 4 New value: enable That assumes VCDS, is that what your gonna use? I used that, the calibration I’ve not worked out properly yet I’ve printed the grid out. I’ll knock a video out once I’ve got the calibration done. It’s not far out to begin with tbh. That’s why I’ve not rushed to do it
Hi Andy, great video. I purchased the same highline RVC from Heycar and fitted it to my NAR 2016 Golf-R with an (earlier retrofitted) MIB2 Discover Pro. I've coded things to what you've posted, and am 99% certain that I have the wiring correct for the KA2/highline (disconnected the right back-up light signal and routed the trigger wire from the camera to the badge-flipper, etc.). My issue is that the badge and camera won't flip open. I can see on the display that the camera is working and the lines are tracking the steering angle and the view modes properly appear. Could you please post the complete long coding strings that you are using for the RVC, 6C and Parking Aid, 76 (or 10)? Might be related: when I code my 6C with VCDS, the values for bytes 3 and 4 are 0 and the drop-downs don't list any model/variant data, so I need to type the hexadecimal values in. Thanks in advance. (By the way, I have heard that ODIS simply will not allow the calibration routine to complete on a Golf because the VIN will always mis-match and the Golf was never equipped with the KA2/highline camera. However, the values supposedly can be copied in using VCP so you can get rid of the "not calibrated" DTC.)
Do you have a blue wire going to the rear light? That works differently to the one I have and how the official VW one does. Some also just work on gyro not taking canbus data at all. Are you after low line or highline coding ?
@@andygardner3177 I disconnected and capped off the blue/black wire from the camera that works its way back to T73a/64 on J519 (and the right backup light, etc. - my rt backup still works) and have everything wired for the KA2 highline, so I am looking for the R189/5GG 827 469 F highline coding and the Park-Assist module coding, too, just to make sure because one of the DTCs I get is: "U1121 00 [009] - Missing Message [message Parkhilfe_01 not received]". So my analysis is that either 6C is not getting the "Open the door" signal because of wrong Hex10/76 coding, or its misinterpreting the signal because of incorrect Hex6C coding. The thing is that we all know that the highline camera relies on CANbus to open the badge, but do we know which module is responsible for sending the command? And, by the way, the US Arteon and Atlas that I've checked both have 5F coded for "BAP VPS msg bus" set for Infotainment Bus, not Comfort Bus, which seems to be the generally accepted channel, so go figure. This is why I'm interested in the full coding strings.
@@BillRehbock some of the cameras use a blue wire to the rear light to know when to open the camera. They just don’t work like the official VW or the camera I brought. Can you share a link to the camera you have?
@@noz3m I’ve printed the board but not got round to it the camera is pretty close I brought as it is. I can’t tell the difference from factory at a quick look. (Friends R)
@@andygardner3177 ah I see so the quality is nice? I like the highline camera but I won't be able to get it calibrated here. Don't have the software.. so not sure if I should get the low or high version. What do you think?
I accidentally unpluged the parking sensors module when i was installing reserve camera on my golf mk5 and now my parking sensor are not working any solution pls
￡130.26 5％ Off | 5GG 827 469 F For Vw Golf 7 Vii Mk7 Flip Badge Logo Rear View Camera 5GG827469F 5GG 827 469 F
a.aliexpress.com/_mLvWWYX I picked the highline and that’s the video.
Great great content! It will be awesome to see a vid of the coding and the part of the fuse box.
Thanks!
The coding is in the description.
That´s awesome, thanks for the video and the full info at the description! ;)
Your welcome let me know if you need anything else. I’d recommend buying the same camera as me if your planning to follow along some have a blue wire not covered in my vid
@@andygardner3177 I'd try to follow the DIY buying from the same store, thank you! ;)
Excellent camera work 😮😮😮😮
Hi, Sorry about that, let me know if I can help in anyway🙂, this is just a hobby, stuck it together to help someone on the forum.
Both our cars, BMW X5 and Golf GTE, have reversing cameras.
What I don't like about the VWs is that as soon as you take the car out of reverse, the camera cuts off.
With the X5 the camera remains for a few additional seconds. So I still have a rear view as I edge forward.
Is it not disabling based on speed?
Character In the video It's great, I like it a lot $$
Great Vieo Andy.
I would like see the parametrization video too.
Carolco
Yeah the AliExpress link I used came parametrised. I haven’t got round to calibration as it’s basically already correct
@@andygardner3177 Dont have any error in unit 10 or 76 unit ?
Thank you very informative, I hope to do mine too 👍🏾
Wouldn’t it have been easier to run cable through roof lining and front door pillar to fuse box ? About to attempt an install on my golf r .
Found it easy to root cable for my rear dash camera that way 🤔
Hi there,
Thanks for the video, as good as I've seen 👍🏻
What I'm not sure about still though is the two orange wires and the red wire up to the back of the MIB2 unit.
I think the red goes to the fuse box?
It's not clear what needs doing to the two yellow/orange ones?
Thanks again,
Mac
Go on the pins and match the colour stripes and you’ll be fine on the canbus connection. Red is the +12v it can go into the back of the fuse box but it’s a right pain. I used a fly wire type thing.
@@andygardner3177 Yeah, that's exactly what I ended up doing. All working well thankfully 😎
@@andygardner3177 fly wire but where did you connect it to?
Hi, do you have the coding instructions too?
Thx for video, very useful, any hints on coding and calibration?
The coding is in the description mate. Calibration I haven’t got round to as it’s close enough so it’s low on my todo list
@@andygardner3177 thx mate! Somehow overlook it.
@@andygardner3177 Camera installed, however getting below error on long coding "marginal conditions have not been met" seems camera is new and do not have basic settings :/
@@AlexKingstonehow did you fix the issue have the same problem
@@kasten8020 Hard to say exactly what helped, but I was in dealership where they had ODIS ( official software ). They tried to code it but got the same error. Next day its simply started to work.
Hi Andy, great video! planning to take on the project myself for a 2019 eGolf (w/ Discover Media). I have a few quick questions.. Do you find the quality of the camera up to the standards of "OEM"/original? or do you think the OE camera from VW will be better quality? Regarding the wiring of this version (highline), there is no need to tap into the reverse light because of the canbus connection, right? My understanding is that there are just 2 canbus wire, 2 video wire, and a 12v power to connect at the back of the MIB unit. (Is there a ground as well?) Any tips on how to pick up the 12v power from the red wire without damaging the original wiring? Thanks!
Hi, The camera looks as good from a visual compare with a friend. You are correct with highline there is no feed from the light. The ground is taken from the car wiring you plug into in order to open the tailgate. The brown and purple connector shown in the video. You can take it put it into the fuse board but this is hard or use a fuse "piggy back"
@@andygardner3177 Thanks so much Andy, fuse "piggy back" sounds great! I guess for us UK cars we just run the wire on the left side and we can access radio and fuse box without wiring going through the middle?
@@leijiao1074 yeah that’s right down the side and then up 🙂 Same for the US they just do the other side.
@@andygardner3177 Great, many thanks! appreciate all the info. I will order the camera now :)
@@leijiao1074have you installed the camera I want one to in my egolf 2020
Do you need to Programm the camera itself with vcp? I only have VCDS
Great vid, I am just having problems to fit the red wire in the fuse box. Any tips?
Also how many Amps fuse do I need ?
Are you trying to use a piggy back/fly wire device or fitting the fuse way in? I have a 7.5AMP fuse in. I think i picked this size based on the factory wiring diagram so it's the same size as if car came with the camera.
@@andygardner3177 thanks. I did it with a piggy back now. Works like a charm :)
Hi Andy, great video. Helped me a lot! Thank you for this. Just wanted to ask if you managed to make the video on coding and calibration? Would really love to do it myself. I have a vagcom
The coding is in the description, I keep trying to get round to playing with the calibration. I have the giant domino printed to scale
@@andygardner3177 thank you, must have missed it. I'll take a look now :)
@@andygardner3177 Hello, did you manage to complete the calibration on your own?
Hi, great video. Is the coding the same for Golf mk7.5?
Hi, I am installing to a 7.5 in the video. The coding is the same.
Great video! The most I have installed so far is the Dashcam, front and back, with connection to the fuse board. How hard is it to install the rear view cam? what tools do I need?
The connection to the back of the fuse board is a nightmare it’s really tight and you need to pull the purple retainers out of the back of the fuse board. I used a piggy back fly wire fuse thing. Tools wise it’s trim tools, trox bits, a socket for the rear seat and tape. I also used a bit of strong wire to help with pulling the cables. I taped the cable to the wire then pushed it thru.
@@andygardner3177 Hey Andy, thanks so much for your help. I fully agree with your approach. I saw some other videos but I don't know why they pull out the screen as well. It should be enough to get out the mib unit in the glove compartment. I sent you a Instagram connection request BTW 😊
Thanks for the video very useful! I am stuck with two orange/brown and orange purple cables that need to go in to the MIB but there was no can bus connector included in to my wiring loom set, do you know if it’s possible to connect them in a different way?
I guess your forced to splice it then my Instagram is mrpandygardner if you need anymore info or want to send me a picture or anything
Hi, Did you have any issues of the display keeps disappearing and needing to do a hard reset on the main MiBII system?
I see you have using the same 12v positive as the head unit did that work fine?
@@thespecialist786 I didn’t have that issue, everything is still working perfectly.
What about the programing video still not uploaded, its basically the most important thing to get the camera working.
I posted the coding in the description. Im trying to calibrate it but this is not needed really it’s close enough for me anyway.
@@andygardner3177 seen the description after i wrote the comment 😂, thank you very much for sharing the information.
I got a oem on my car. The screen i black when in turn on reverse. I have a new camera installed and it not work. fail code no signal
Hello, greetings from Spain. my camera shows error B201000. Does it mean that it is not parameterized? or what is missing to calibrate? Do you know if it can be done in obdeleven? or vagcom? Thank you
Hi my friend please I want to ask you, the higline reversing camera retrofit have 3 or 4 deferent mode of view, I want to ask those options of view into the camera or you need to change some unit on your car to get it?
Hi they can be coded in, I have them coded in. If you follow the coding in the description they are there.
My friend , I just want to know the options into the camera or the unit of the car , by the way install it in my car but I not have those mode of view the car seat Leon mk3 cupra, I am afraid 😟 my unit not have it that all if I have have to change the camera I will do it no problem 😊
Guten Tag, ich heute Kamera eingebaut in ein Versand t roc und das Problem das die Kamera nichts anzeigt.Könenen sie ein Video machen wie es codiert wird.
Danke
Hi mate, I was just wondering if you could make a short video of the quality of the camera etc. Thanks!
Do you mean image quality?
@@andygardner3177 yeah mate! Exactly that sorry I worded so poorly haha.
@@aadamc8329 this is in the dark ibb.co/S0NQZmM it’s pretty clear. Before I coded the other modes in.
nice video cheers
Hi im planning to buy the camera. Do you have a pdf or instructions for the coding and calibration thx.
Coding from: ilovecarmods.com/vw/composition-media-mib2
Module: 5F (Information electronics)
Coding → Long Coding → Byte: 19 → Bit: 4
New value: disable
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B
New value: activated
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B_msg_bus
New value: Comfort data bus
Module: 76 (Parking aid)
Coding → Long Coding → Byte: 02 → Bit: 4
New value: enable
Module: 19 (CAN getaway)
Adaptation → Channel: Installation list; specified installations - Camera System Rear View
New value: Coded
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 0
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 1
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 2
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 4
New value: enable
That assumes VCDS, is that what your gonna use?
I used that, the calibration I’ve not worked out properly yet I’ve printed the grid out. I’ll knock a video out once I’ve got the calibration done. It’s not far out to begin with tbh. That’s why I’ve not rushed to do it
Hello brother i have bought wiring for my rear camera but it doesnt have the orange splitter in your video how can i bypass ir
Does it have two orange wires?
Hi Andy, great video. I purchased the same highline RVC from Heycar and fitted it to my NAR 2016 Golf-R with an (earlier retrofitted) MIB2 Discover Pro. I've coded things to what you've posted, and am 99% certain that I have the wiring correct for the KA2/highline (disconnected the right back-up light signal and routed the trigger wire from the camera to the badge-flipper, etc.). My issue is that the badge and camera won't flip open. I can see on the display that the camera is working and the lines are tracking the steering angle and the view modes properly appear. Could you please post the complete long coding strings that you are using for the RVC, 6C and Parking Aid, 76 (or 10)? Might be related: when I code my 6C with VCDS, the values for bytes 3 and 4 are 0 and the drop-downs don't list any model/variant data, so I need to type the hexadecimal values in. Thanks in advance. (By the way, I have heard that ODIS simply will not allow the calibration routine to complete on a Golf because the VIN will always mis-match and the Golf was never equipped with the KA2/highline camera. However, the values supposedly can be copied in using VCP so you can get rid of the "not calibrated" DTC.)
Do you have a blue wire going to the rear light? That works differently to the one I have and how the official VW one does. Some also just work on gyro not taking canbus data at all. Are you after low line or highline coding ?
Do you have a link to the camera you brought?
@@andygardner3177 I disconnected and capped off the blue/black wire from the camera that works its way back to T73a/64 on J519 (and the right backup light, etc. - my rt backup still works) and have everything wired for the KA2 highline, so I am looking for the R189/5GG 827 469 F highline coding and the Park-Assist module coding, too, just to make sure because one of the DTCs I get is: "U1121 00 [009] - Missing Message
[message Parkhilfe_01 not received]". So my analysis is that either 6C is not getting the "Open the door" signal because of wrong Hex10/76 coding, or its misinterpreting the signal because of incorrect Hex6C coding. The thing is that we all know that the highline camera relies on CANbus to open the badge, but do we know which module is responsible for sending the command? And, by the way, the US Arteon and Atlas that I've checked both have 5F coded for "BAP VPS msg bus" set for Infotainment Bus, not Comfort Bus, which seems to be the generally accepted channel, so go figure. This is why I'm interested in the full coding strings.
@@BillRehbock some of the cameras use a blue wire to the rear light to know when to open the camera. They just don’t work like the official VW or the camera I brought. Can you share a link to the camera you have?
Does your camera have a blue wire if so it doesn’t work like the official VW one or this one I’ve fitted? They only use the canbus for steering
Did you get the high or low line?
if you did the highline, were you successful with the calibration?
High. There different “high” on AliExpress. Mine works like the official VW one. There’s a link to the one I brought in the description.
I haven’t dug into calibration.
@@andygardner3177 all I hear that it's impossible to calibrate it. Do you find it works good enough as is? So without the calibration?
@@noz3m I’ve printed the board but not got round to it the camera is pretty close I brought as it is. I can’t tell the difference from factory at a quick look. (Friends R)
@@andygardner3177 ah I see so the quality is nice? I like the highline camera but I won't be able to get it calibrated here. Don't have the software.. so not sure if I should get the low or high version.
What do you think?
hai
i bought in aliexpress highline camera for golf 7. it's open but i dont get video. can you give coding pls.
Coding from: ilovecarmods.com/vw/composition-media-mib2
Module: 5F (Information electronics)
Coding → Long Coding → Byte: 19 → Bit: 4
New value: disable
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B
New value: activated
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - VPS_0x0B_msg_bus
New value: Comfort data bus
Module: 76 (Parking aid)
Coding → Long Coding → Byte: 02 → Bit: 4
New value: enable
Module: 19 (CAN getaway)
Adaptation → Channel: Installation list; specified installations - Camera System Rear View
New value: Coded
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 0
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 1
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 2
New value: enable
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 07 → Bit: 4
New value: enable
Do u know if this will fit mib1 or where to check 😬😬
At the bottom of the description mate
Any news about calibration?
I haven’t looked at it because it’s so close. I might get round to it at some point.
Hello, do you know if i can install hightline rear view camera, if i have on my car MIB 1?
There’s a list of part numbers in the description if you hold menu the part number will come up.
I accidentally unpluged the parking sensors module when i was installing reserve camera on my golf mk5 and now my parking sensor are not working any solution pls
Plug it back in 👍
This one work with radio 5G0035819A ??
Hi, No it doesn’t.
Links to buy ?
It’s a pinned comment
Good job!, please next time take horizontal video to see better
NOW 199,64 ￡ WTF