Most are not in oil. Most are on the side either sealed or out of the oil level. Even though some oil does get over there, it doesn't affect the electrical generation.
3 ปีที่แล้ว +1
Just saw the comment but Dayward1 gave the answer already. Thank you
Hi What's the name of that extraction tool and where can I buy one from? Cheers
3 ปีที่แล้ว
it is used for pulling bearings but i had nothing else to use at that time. It is called a bearing puller. The proper tool to remove the flywheel is called flywheel puller. You can see it in this video th-cam.com/video/l1RqdzfvC5k/w-d-xo.html
@ mct 250 ama gerçekten artıka anahtarın ağzı büyüdü ve yalama olacaktı bende bıraktım bir elrktirikli tork almak istiyorum 450nm gücünde sence açarmı bunu gücü yetermi yada kaç nm lik almam lazım çektirmem falan var tek sıkıntı volntın vidası gevşemiyor keçe patladı ustada yok kendim yapmam lazım
6 ปีที่แล้ว
bazen civataları ters diş yaparlar. Yani sağa soğru çevirerek açman gerekir. Ona dikkat et. Sola doğru çevirince açılmıyorsa sağa soğru da dene bir iki kere. Somun sökme alırsan işin kolaylaşır tabi. 450 iş görür. Benim kullandığım da 450nm. ikinci el çin vs bişeyler alabilirsin ucuz ne varsa
I was stuck on removing the nut holding the alternator on until I watched this video. Thanks for posting it.
You're welcome
The tool at 4:40 can be called a strap wrench.
Very good video. Helped me a lot! Thanks!
You're welcome!
Always use the nut on the bolt or you can damage the threads
Sir What will happen if timing chain goes lose and get tick tick noise?
Any problem for pickup and acceleration??
A bit loose will make noise. Too much loose complete engine failure.
@ thnks sir any problem for compression?
@@kishanpreston1533 it is possible
@ thank you for fast reply🤙
I got crf150f, i also had some issues with it.
hope you sort them out as two grown up
why all scooter engine generator side is dry
and in most of motorcycle generator side is wet?
Just simplicity. Oil doesn't harm it, and to seal it means another seal and more complexity and less reliability.
Most are not in oil. Most are on the side either sealed or out of the oil level. Even though some oil does get over there, it doesn't affect the electrical generation.
Just saw the comment but Dayward1 gave the answer already. Thank you
Question the box with like zig zag lines on it is it air box for intake?
can you write which minute and second you saw it in the video
Hi
What's the name of that extraction tool and where can I buy one from?
Cheers
it is used for pulling bearings but i had nothing else to use at that time. It is called a bearing puller. The proper tool to remove the flywheel is called flywheel puller. You can see it in this video th-cam.com/video/l1RqdzfvC5k/w-d-xo.html
Good video thanks
Merhaba cg tip motorda statör tarafında yağ olması normal mi yoksa keçe değişimi mi gerekli. Yardımcı olursanız sevinirim
ağzına kadar yağ doluysa vardır bir sıkıntı yoksa yağlı olmasında bir sorun yok.
@ teşekkür ederim
Thank you !
what is the size of flange nut, please...
metric 19
@ thanks 🙏
Thanks
Nice video, I broked key woodroff too make my ignition timing abnormal. Owners manual says that the key must clean of engine oil in installation.
mine didnt said anything but I was also wondering if i should oil or not. I decided to smear everything in oil:)
Perfect 👍
th-cam.com/video/l1RqdzfvC5k/w-d-xo.html
This engine is same as my Honda dazzler
Didnt know. Thank you
Helal abi sende ingilizcedemi vardı 😂 bu arada abi bu volant açılmıyor vidası gevşemiyor yani bir yöntem söyler misin bana
cbf 150 mi
@ mct 250 ama gerçekten artıka anahtarın ağzı büyüdü ve yalama olacaktı bende bıraktım bir elrktirikli tork almak istiyorum 450nm gücünde sence açarmı bunu gücü yetermi yada kaç nm lik almam lazım çektirmem falan var tek sıkıntı volntın vidası gevşemiyor keçe patladı ustada yok kendim yapmam lazım
bazen civataları ters diş yaparlar. Yani sağa soğru çevirerek açman gerekir. Ona dikkat et. Sola doğru çevirince açılmıyorsa sağa soğru da dene bir iki kere. Somun sökme alırsan işin kolaylaşır tabi. 450 iş görür. Benim kullandığım da 450nm. ikinci el çin vs bişeyler alabilirsin ucuz ne varsa
@ eyvallah sordum mctolanlara sol tarafmış genede sağ ol hocam çok kralsın korkum tork makinesiydi oda olacak inşallah
evet sağa çevirmen lazım açmak için. Bu eleman söküyor motoru ona bakabilirsin
th-cam.com/video/8_l1-PYK3O4/w-d-xo.html
It not corect i can damage the flyweel
You can damage anything if you are not careful.
To much talk...just show the move
Too much to tell. You move in the video where you need to.
shut up and listen
My college automotive instructor came up with this one. "Two ears, one mouth!"
no good
no comment
Very talk tu much,,pu