@@fatalerror4296 It was just kidding. I learned welding while serving in the military. For free. And I know that welding in that video is not difficult.
No kidding! Now you have holes in your wall and in the door! And when he opens that door to full extension, that rod is going to find a home in that wood. 😳
Wouldn't be surprised if this is more expensive lmao, a tigh tension spring with a specific size like that would not only take a decent amount of time yo find but is probably like $15 on its own, plus a $2 bolt and $1 in nuts, thats $18, i just looked on google and the first one that came up was $18.12 from ace, and the second one was $15 lmao
Да в любом случае, не более чем на несколько раз. А пружина то неисвромятина должна быть, так же как и всё остальное, что б не порыжело. Я к тому, что и себестоимость у изделия по нонешним временам немаленькая будет.
Aside from how stupid it is to build something like this that you could buy for a few buck, there's a couple engineering flaws to it: The welds will break soon because spring steel (in this case, probably class 2 wire) doesn't weld well. It won't have much preload tension on it so if the hinges have ANY drag it will stop before closing. The metal on metal fit where the bar slides through the mount on the door will quickly wear and provide a lot of extra drag. And it's not offset from the door frame enough to allow the door to go much past 90 degrees.
Also the direction of the spring is tightening and theres no space for it to get any smaller so the amount it opened in the video is probably as wide as it will ever open before it breaks
Двенадцать стульев Часть 1. Старгородский лев Глава 10. Голубой воришка Дверные приборы были страстью Александра Яковлевича. Положив великие труды, он снабдил все без исключения двери пружинами самых разнообразных систем и фасонов. Здесь были простейшие пружины, в виде железной штанги. Были духовые пружины с медными цилиндрическими насосами. Были приборы на блоках со спускающимися увесистыми дробовыми мешочками. Были еще пружины конструкций таких сложных, что собесовский слесарь только удивленно качал головой. Все эти цилиндры, пружины и противовесы обладали могучей силой. Двери захлопывались с такою же стремительностью, как дверцы мышеловок. От работы дверных механизмов дрожал весь дом. Старухи с печальным писком спасались от набрасывавшихся на них дверей, но убежать удавалось не всегда. Двери настигали беглянок и толкали их в спину, а сверху с глухим карканьем уже спускался противовес, пролетая мимо виска, как ядро.🤣 Извините, чёт навеяло...
Мой троюродный брат инженер. Он предлагает открыть цех прям в квартире по сборке сварочных аппаратов и станок поставить по изготовлению пружин.идея так себе, но с инженером не поспоришь. 👍
People that do have welders are the type of people this is for. You could put this in an outhouse you built, a clubhouse, deer blind, shooting shack, ice shanty etc. Looks like it would work better than the gas strut types they sell in stores for those applications too.
Сразу два недочёт. Прижимную планку надо было торцом приваривать и на кронштейне пружины точки крепления со стороны двери нужно повернуть на 90°. Тем самым максимально совместив ось пружины с осью дверных петель.
Когда я рос в советском союзе такими "доводчиками" были оборудованы 90% дверей. Еще проще конструкция, два крепежа и пружина на растяг. Ни сварки, ни шурика не надо было.
@@Jesse_Carreon once you have a welder, things you can make / repair things that compensate very quickly the welding machine cost . How do you value experience ?
Lmfao I just imagined myself saying this to my woman and what she'd say 🤣 I do. Do alot.of welding so she'd just probably be like your legs arent broke 🤣
This is a great idea if you need a door closer for your secret torture room and you don't want any questions from some nosey clerk at a hardware store...
Me: buys a $99.99 welder from harbor freight, welding gloves, apron, mask (because I didn’t know that little T-shaped thing that came w/ the welder was a mask), flux core welding wire, bench vise for holding the parts, a bolt, 3 nuts, a spring, some screws, and some steel bar, and a bench grinder for finishing the edges. Also me: realizing my now $275 door closer has the spring backwards.
torsion spring might need 90° worth of elasticity (if that makes sense, i mean if u push the spring beyond 90° elastic limit is reached) only looks to make it 45° here. As for the bar its at a 90° offset to the door, opening the door the full way means it will just barely reach if at all. I suggest starting at an offset to the bar beyond 90° and use a different spring, that beint said v good concept, not anything ive done
Seems to be at a cabin, where it might not be practical to pop out to home depot or wait for Amazon to get to you. Besides, if you're a tinkerer building it from scraps, the cost is 0
Only one problem, the pivot points of the door and the closer are in different positions so the rod arm will jam on the slide bracket and won't allow the door to open fully with out modification.
For the comments about the door not opening, that door can clearly open wider than 90 degrees. The problem is, there's no way to adjust tension or release tension when you want to leave door open. Store bought door closers can be adjusted and many have a feature to hold the door open.
@AztecWarrior69 it will open 100° or maybe 120° but not 180° . There are door stoppers made to stop doors from opening 180° . They attach to the hinge and work in the exact same way. If you look at one, you'll understand what we're talking about. If you think it won't open then you just don't understand what you're talking about.
@@brookelord3448 What the hell are you talking about? 180 I never mentioned or asked if it will open 180. I am telling you it Won't ever even get to 90 degrees, Period.
You can get it for like 120$ in india. We owned this basic Weilding machine because labor cost for even a simple work cost as much as complicated work 🤦♂️
Какая дверная пружина? Есть ссылка? Ты думаешь, все в мире тупые, а твой народ самый умный? До тебя технологии позднее чем до Индии доходят вообще-то. Пружины цепляют снаружи и она портит краску, а это изнутри ставится.
When you're in the middle of the woods and you dont have a car to drive to HomefvxknDepot, but you have a shop in the cabin with electricity, welding equipment, and a TH-cam video recording setup.
It's like when you was a kid wanting to replicate art from a TV show but they took out a professional art supply and materials that no 8 y/o kids ever have.
Когда нам было лет по 8-10 сосед Игорь Феофаныч пришпандорил прежину что трактором не разогнуть. Мы жили на втором этаже, так эта дверь так шарахала что телек подпрыгивал и мы все дружно с жильцами вспоминали дядю Игоря не совсем хорошими словами. Кто то пошел и оторвал эту пружину. А дверь то деревяггой была на улицу. Уж лучше бы дядя Игорь рессору к двери пришпандорил. Сейчас мне 40 лет. До сих пор помню дядю Игоря. А как то утром он разбудил двор от того что начал сверлить в тазике дырки. Как он сказал - это острая необходимость. И это в 7 утра летом. А дом у нас был 2-х этажный на 24 кв. Спасибо тебе дядя Игорь за наше незабываемое детство
А вот у одного изобретателя очень туго открывалась входная дверь. Когда его спросили, почему дверь так туго открываются, он сказал, что при открытии воды из колоца откачивается на поверхность 8.5 литра воды. Его спросили: а почему именно 8.5 литра? Он ответил: К сожалению дамы при большем количестве воды не в состоянии открыть дверь!
First step: Buy a $500 welder
Lol 😂
2ND step : Enroll in a $10,000 college to learn welding skills.
Welders can cost as low as 100 dollars.
@@Minseok_Ko you dont need to go to college to weld. Im in high-school and im taking a welding class right now. Its not hard at all.
@@fatalerror4296 It was just kidding.
I learned welding while serving in the military.
For free.
And I know that welding in that video is not difficult.
How to make a door closer cheaply: Go to the store and get that $2 thing
and it will run ten times longer
No kidding! Now you have holes in your wall and in the door! And when he opens that door to full extension, that rod is going to find a home in that wood. 😳
В России это не 2$ стоит а дорого
And you give your cat a toy
Wouldn't be surprised if this is more expensive lmao, a tigh tension spring with a specific size like that would not only take a decent amount of time yo find but is probably like $15 on its own, plus a $2 bolt and $1 in nuts, thats $18, i just looked on google and the first one that came up was $18.12 from ace, and the second one was $15 lmao
It's not cheap, its genius.
Вы пробовали в таком варианте дверь открывать полностью?
😂😂😂😂😂😂
Остап Бендер пробовал
It has to be impossible
Да в любом случае, не более чем на несколько раз.
А пружина то неисвромятина должна быть, так же как и всё остальное, что б не порыжело.
Я к тому, что и себестоимость у изделия по нонешним временам немаленькая будет.
@@joshuaphillips4958
Door only opens half way 👌🏽
BUT…… It CLOSES BY ITSELF. Stop hating.
@@sgvincent100 LMAOOOO
@@sgvincent100 Lmaooo so what’s the point of it closing if you can’t even open it right?
@@sgvincent100 that's like cutting the roof off a car and saying WELL NOW ITS A CONVERTIBLE STOP HATING
Ya they didn't show the part where the rod gouges the door
Nobody:
That one guy who learned how to weld yesterday:
Hahahahaja
Lol
That was legitimately me 😂
Hahaha. What do you men by "Nobody:"
irrelevant for this use, as long as it works its ok
先ず、普通の家に溶接器具が無いwww
I learnt that www at the end of your sentence translates to lol
Aside from how stupid it is to build something like this that you could buy for a few buck, there's a couple engineering flaws to it:
The welds will break soon because spring steel (in this case, probably class 2 wire) doesn't weld well.
It won't have much preload tension on it so if the hinges have ANY drag it will stop before closing.
The metal on metal fit where the bar slides through the mount on the door will quickly wear and provide a lot of extra drag.
And it's not offset from the door frame enough to allow the door to go much past 90 degrees.
Всё делать самому, нужно много времени и денег. Пойдём, лучше мамонта завалим.
Also the direction of the spring is tightening and theres no space for it to get any smaller so the amount it opened in the video is probably as wide as it will ever open before it breaks
@@user-xs7ru2ii9lforeign comments always say the weirdest shit
how about the fact this is just a spring and yet the door closes like there's a dampening system preventing it from slamming like this system would
Not to mention what an eyesore!
В любой непонятной ситуации нужно варить пружину или подшипник
Некоторые не только варят, но ещё и жарят!
Двенадцать стульев
Часть 1. Старгородский лев
Глава 10. Голубой воришка
Дверные приборы были страстью Александра Яковлевича. Положив великие труды, он снабдил все без исключения двери пружинами самых разнообразных систем и фасонов. Здесь были простейшие пружины, в виде железной штанги. Были духовые пружины с медными цилиндрическими насосами. Были приборы на блоках со спускающимися увесистыми дробовыми мешочками. Были еще пружины конструкций таких сложных, что собесовский слесарь только удивленно качал головой. Все эти цилиндры, пружины и противовесы обладали могучей силой. Двери захлопывались с такою же стремительностью, как дверцы мышеловок. От работы дверных механизмов дрожал весь дом. Старухи с печальным писком спасались от набрасывавшихся на них дверей, но убежать удавалось не всегда. Двери настигали беглянок и толкали их в спину, а сверху с глухим карканьем уже спускался противовес, пролетая мимо виска, как ядро.🤣
Извините, чёт навеяло...
@@user-lx9zt1zt3u эх, перечитать что ли это шикарное произведение?!
@@user-lx9zt1zt3u when the comment to the comment is better than the video 😂
Автор просто не знает что нельзя варить пружину и подшипник
“How to make a door closer cheaply” proceeds to weld.
“Cheap materials”
@@cringecrusader6985 you realise a welder required a welding material, right?
@@Reptile_Gecko yeah so it’s for people who have one already are you daft
“Next video I’ll be showing how to cheaply make concrete from moon rocks (hint: they are free, all you have to do is go get them)”
@@Reptile_Gecko fair point
wauw. prachtig idee. dank je wel voor het delen
I love this, thanks a lot
Есть ощущение что пружину варить идея просто отличная 😅😂
Почему? Просто сварочник далеко не надо убирать, поставить рядом с этой дверью и подваривать когда это нужно будет.
@@Matev123 можно даже прикупить недорогой полуавтомат б.у. и поставить рядом, если основной сварочник часто нужен.. так что отличный лайфак.
Вы не правы, этот полезный совет не для закрытия двери, а для создания новых рабочих мест.
Мой троюродный брат инженер. Он предлагает открыть цех прям в квартире по сборке сварочных аппаратов и станок поставить по изготовлению пружин.идея так себе, но с инженером не поспоришь. 👍
@@toptygin007 Анжанеры знают толк))))
Лайфхакеры перешли от сварки подшипников к сварке пружин... Прогресс 😂
TheDèrgraue, прогресс и никуда не деться. Был подшипниковый хакерлайф, стал - пружинный.
@@user-mv8jm4yq5r lo de o. llevo lo
om lo ook
@@user-mv8jm4yq5r lo lo
th-cam.com/users/shortsOFgUPdsFqNk?feature=share
I love it .
Wow this is fantastic I lovedit
The weight of my door and the angle of my house are in perfect balance that the door already closes itself
Then you must be needing a door stopper. Guess this guy would tell us how to manufacture that as well.
@@impuneetverma Nah I like that it closes itself. It’s usually closed so when I leave to head out of my room gravity does its work for me
Oblivion npc detected
@@impuneetvermayeah you need a door stop to prevent you from closing your door in the first place🤣that’s the optimal strategy
Weird flex but ok
They’re cheaper than the materials you used to make that. Not to mention, not everyone has a welder sitting around their house😭
.7
6
هه
8تتخ۵۷
Ya
Sshh. Its a life hack video. It must be useful in your life.
People that do have welders are the type of people this is for.
You could put this in an outhouse you built, a clubhouse, deer blind, shooting shack, ice shanty etc. Looks like it would work better than the gas strut types they sell in stores for those applications too.
В деревне может быть полезно
Instructions unclear, I lose a limb everytime I walk through this door
Сразу два недочёт. Прижимную планку надо было торцом приваривать и на кронштейне пружины точки крепления со стороны двери нужно повернуть на 90°. Тем самым максимально совместив ось пружины с осью дверных петель.
Всё эта приблуда один большой недочёт!
Все хорошо и классно, но это не доводчик, а хлопатель двери.👍😁
Да. Вернее захлапыватель. Нужен ещё демпфер чтобы не хлопало а доводило.
@@Otrem3501 вот тогда это будет доводчик)))
Когда я рос в советском союзе такими "доводчиками" были оборудованы 90% дверей. Еще проще конструкция, два крепежа и пружина на растяг. Ни сварки, ни шурика не надо было.
@@Otrem3501 согласен 👍
@@den8kk876 Всё верно 👍. Я считаю, что моя родина СССР. Мне 60+. Удачи по жизни!
How to make a door closer for cheap
Step 1: go out and buy a welder because you probably don't have one lying around
It's possible to make one at home.
@@johnalves7168 im sorry but how do you just make a welder at home?
Step 2: Learn how to weld because you likely don’t know how to weld.
@@HDent64I saw MacGyver do it with a car battery, jumper cables and two quarters. I believe that’s an arc welder if I’m not mistaken.
Playing
Maaan! That's genius
Nice job 👍
Есть ощущение, что дверь не полностью в таком положении откроется, нужно отверстие овальное делать в ответной планке🤔
это да и кол-во витков увеличить чтобы сварной шов не лопнул
Через 15 лет отверстие само станет овальным
ЗДА-А-СЬТЕ !!!
دقیقا
@@user-iz3gp3zj1z
250полуляхов из 250
Ah yes cheap materials… now where do I get a $5 welder?
Neat idea for a low cost
solution to a problem!
Was für ein toller Hecht!
I don't need that. If I want the door closed I'll start an argument with my wife. She'll slam the door.
😂😂😂😂
Modern problems require modern solutions
I just need to open my mouth, don't even need to start an argument. She is very understanding... She'll start the argument on her own
Great!
@@infinow 😂😂😂😂poor man!
Your door stop makes it so the door doesn’t open very far. You’ll either be forced to deal with that, or it’ll snap off.
It will go to 90 degrees, right? Why does it need to open more than that?
@@aw8388 it wont, stressing a spring like that leads to breaking, especially with a bad weld
The rotational point isn’t in line with the doors arc of opening so yeah that wouldn’t open far
Or his going to have nice gouge marks out the door.
At least the bar that connects the spring to the door is loose that way it has wiggle room for the difference of the hinge placements
Звуковые эффекты которые мы заслужили:
The life span is short due to the spring solder ... It is best to make a ninety-degree bend pulsating
Can't wait to hear the FunkFPV commentary on this one.
Sameeee
Came here to write exactly that!
Omie lol
Oh! Shit son!
Probably point out how it looks like the guy almost welded through the spring. Wont be long before it snaps
Кхе, кхе...
ДОКТОР ДЬЮ, У НАС КЛИЕНТ!!!
Да, он такую хуйню ещё не разбирал
Доктор сибасся в тёплые края
@@116volt9 это ты сибаса, а он с нами
@@bespod2421 где это? С вами. В мыслях? 😂
L
Nice work 👏 👌 🎉
錆びたらギーギーいいそうだけど良い仕組みだ。プラモとかの小さいギミックに良さそう
How to make sure you can never fully open your door again
Bro how are you complaining about the thing it was MADE to do. I swear some of you needed to get bullied more.
@@MegaSPAZ2010 yeah. Like you. Cause that door closer is gonna snap pretty soon. You’re hardly able to open the door anymore
@@MegaSPAZ2010 literally those thing probably gonna spin harder then the afton springlock suit
@@MegaSPAZ2010it was made to close an open door, not to prevent a door from opening
😊норм
Тема
These type door hinges are already cheap but I guess I’ll have to go and buy a welding machine and run a 220/240 line for it.
A Harbour Freight MiG welder is 99.00 and runs on 110V
And a door hinge is $4 and runs on 0V what’s your argument here?
@@Jesse_Carreon once you have a welder, things you can make / repair things that compensate very quickly the welding machine cost . How do you value experience ?
I prefer my home to not look like I've made it out of whatever junk I found lying around
Конечно он это собрал из металлолома, но сама идея интересна, если наладить полноценное производство и доработать изделие
@@user-xg9jz2om3gприварить подшипник)
Это можно использовать и не для дома, а например для сарая или курятника.
Но ведь если у тебя есть ферма или гараж какой-нибудь, то это не плохой вариант.
Lol!
Thank you so much
Now I'd like to see you fully open the door.
You reckon the 1 tack weld will hold against that much force?
@@SkyJUSTIN6 Exactly why I commented this lol.
'Let's see how deeply this bar gouges into the door surface before the weld shears'
😂🤒
"Honey? Plug in that welder."
"What are you gonna do?"
"I'm about to keep this door shut!"
Lmfao I just imagined myself saying this to my woman and what she'd say 🤣 I do. Do alot.of welding so she'd just probably be like your legs arent broke 🤣
😂😂😂😂😂
На конец рычага на двери который вставить пружинку на сжатие, тогда дверь не будет хлопать.
Looool funny people
That is amazing
This is a great idea if you need a door closer for your secret torture room and you don't want any questions from some nosey clerk at a hardware store...
Я человек простой вижу когда гайку к болту приваривают листаю дальше🤣🤣🤣
А где здесь гайку к боту приваривают интересно?
@@--7785 Он увидел болт с гайкой и пролистал дальше
@@user-hi2eq8cc4s он у видел шо там приварили гайку а приварив гайку к пружине надо было приварщику морду набить за безполезное потраченое время
굿~~~입니다.
아이디어가 참좋아요.😊
Simple and Robust design 😊 I praise guys innovative ideas....❤ Small step towards innovation makes big difference in society 😊
Me: buys a $99.99 welder from harbor freight, welding gloves, apron, mask (because I didn’t know that little T-shaped thing that came w/ the welder was a mask), flux core welding wire, bench vise for holding the parts, a bolt, 3 nuts, a spring, some screws, and some steel bar, and a bench grinder for finishing the edges.
Also me: realizing my now $275 door closer has the spring backwards.
Never buy Flux lol it burns way too hot
@@Reezour_Waargh .
You said it first hahaha. I was comin here to say that exact thing.
But u have the tools now. So u can make a cheap new one.
Couldn't have addressed that better myself
Thank you so very much
torsion spring might need 90° worth of elasticity (if that makes sense, i mean if u push the spring beyond 90° elastic limit is reached) only looks to make it 45° here. As for the bar its at a 90° offset to the door, opening the door the full way means it will just barely reach if at all. I suggest starting at an offset to the bar beyond 90° and use a different spring, that beint said v good concept, not anything ive done
Step 1: Buy all these tools for 500$
Step2 : When you mess up, get the final product online for 17.99
В России можно купить инверторный сварочный аппарат за 50-100 долларов и он тебе ещё пол жизни прослужит, так что первый пункт отменяется
😅😊😅😅
In Russia, even children have a welding machine. I have been welding parts since I was 9 years old.
@@Goterias and let me guess now you are 10.
@@Goterias the whole world doesn't revolve around russia
Как в "12-ти стульях"
Главное успеть проскочить, чтобы по хребтине сзади не получить)
Russian always think 👍😘
Love it!
Great video
"I have some trust issues with the welding" 💀💀
Muito bom
It’s still more solid than gorilla tape
You gonna hang over a cliff on them welds or what?
@@Maradnus 8,h8g8 8g7g😏😃😏😃
@@Maradnus &7g 📢📣🔋📣🔋📢📢📱
If you can afford a welder, you can afford a door closer
There’s no glory on buying.
@@trineodecalle True, but there is more money left in the wallet.
Seems to be at a cabin, where it might not be practical to pop out to home depot or wait for Amazon to get to you. Besides, if you're a tinkerer building it from scraps, the cost is 0
For sure.
What if that’s ur job, and they let u take the equipment home?
Nagyon ötletes, kapura megfelelő.
Its gonna be a nice line with no paint if you have a painted door
I love how he can’t open it all the way. Door closer meaning it keeps the door closed. That rod gonna scrape the hell outa that door
Yes door closer has two arms that hinge
Next video: how to make a 50 cent pencil by just using $2 in crude material and 3 hours of your time !
Muito bom GOSTEI
Smart idea 😊
Мне как раз дверь нужно открыть на 20см, чтобы просунуть лицо в соседнюю комнату
А мне в форточку женской бани
колено и шарнир можно приделать...
Лопнет пружина на стыке сварки при первом же открывании.
Как мы видим не лопнула
@@GROtesknayaStoleshnica228 так дверь приоткрыли
С чего вдруг?
Usa 70 18 🤷♂️
Eventually the weld at the spring will break.
Congratulation zanmim bon travay..
A spring hinge from home Depot for $15.00 will do the same thing.
Next video: how to cast broken fingers from doors that are closed using high strength springs cheaply
🤣
The spring is now super brittle where it's been welded, it won't last long before breaking anyway.
Ask me how I know...
Only one problem, the pivot points of the door and the closer are in different positions so the rod arm will jam on the slide bracket and won't allow the door to open fully with out modification.
Всё правильно, автор дверь до конца так и не открыл.
All i need is one of those cheap cold fusion welders from Temu and then we will see it if works🤨
I like the sound affects.😊.
Walmart sells a door closer for 10 bucks that also comes with a metal tab that can be slid to hold it open. Installs in minutes.
Yeah but that doesn't require stick welding, where's the fun in that?
For the comments about the door not opening, that door can clearly open wider than 90 degrees. The problem is, there's no way to adjust tension or release tension when you want to leave door open. Store bought door closers can be adjusted and many have a feature to hold the door open.
All you need are holes (at various intervals depending on how far you want the door open) on the threaded rod and a small screw
Ну в баню пойдет, по тому что там всегда нужна жара и что бы не выходила от туда
Wrong it will not open 90. T
@AztecWarrior69 it will open 100° or maybe 120° but not 180° . There are door stoppers made to stop doors from opening 180° . They attach to the hinge and work in the exact same way. If you look at one, you'll understand what we're talking about. If you think it won't open then you just don't understand what you're talking about.
@@brookelord3448 What the hell are you talking about? 180 I never mentioned or asked if it will open 180. I am telling you it Won't ever even get to 90 degrees, Period.
Kapı bu şekilde tam olarak açılamaz. Metal çubuğun kapıya gelen kısmında yuvarlak parça U şeklinde yapılmalıdır
2 spring hinges = 10$ … 2 hours of time = priceless
Ты курс то видел рубля?
Это же половина рабочего дня в России
It won't fully open now
No but you don’t need full 180 degrees in most situations
@@ak14619 180 degrees? Where do you live? In a 1800s saloon? 🤣
That door won't even open 90 degrees like most doors would now.
No it won’t. In USA it won’t pass inspection. It calls egressing Since the door won’t open at least 90 degrees
Yes it would. There's nothing stopping it opening a full 90 degrees.
Love how it shows just that top corner of the door. Can't even tell if it works.
The guy might be just closing the door himself.
Wow excellent
thats like something I'd see in a dive bar
People everywhere are pissed their door doesn't open all the way anymore.
Eso parece 🙄🙄 da la sensación que abre poco ...
“How to make a cheap door closer”
Proceeds to use very common household item known as a “welder”
You can get it for like 120$ in india. We owned this basic Weilding machine because labor cost for even a simple work cost as much as complicated work 🤦♂️
A welder in rural America isn't that uncommon. I grew up with access to 2 tig machines, a gas stick welder, and a mig.
Excellent 😮
its amazing master
Они офигеют еще, когда узнают, что дверная пружина за 156 рублей делает то же самое, только лучше и проще.
Какая дверная пружина? Есть ссылка? Ты думаешь, все в мире тупые, а твой народ самый умный? До тебя технологии позднее чем до Индии доходят вообще-то. Пружины цепляют снаружи и она портит краску, а это изнутри ставится.
Disclaimer: Requires bodybuilders to open door fully
😂
🤣🤣
Good idea keep it up
When you're in the middle of the woods and you dont have a car to drive to HomefvxknDepot, but
you have a shop in the cabin with electricity, welding equipment, and a TH-cam video recording setup.
It's like when you was a kid wanting to replicate art from a TV show but they took out a professional art supply and materials that no 8 y/o kids ever have.
Когда нам было лет по 8-10 сосед Игорь Феофаныч пришпандорил прежину что трактором не разогнуть. Мы жили на втором этаже, так эта дверь так шарахала что телек подпрыгивал и мы все дружно с жильцами вспоминали дядю Игоря не совсем хорошими словами. Кто то пошел и оторвал эту пружину. А дверь то деревяггой была на улицу. Уж лучше бы дядя Игорь рессору к двери пришпандорил. Сейчас мне 40 лет. До сих пор помню дядю Игоря. А как то утром он разбудил двор от того что начал сверлить в тазике дырки. Как он сказал - это острая необходимость. И это в 7 утра летом. А дом у нас был 2-х этажный на 24 кв. Спасибо тебе дядя Игорь за наше незабываемое детство
Nice one. I used 2 screws and a bungee cord.
mom: Stop slamming ur damn door
me: Its the auto closer
Варенная к стержню пружина, долго не простоит, лопнет или по месту сварки или рядом.
Мыши съедят, или моль заведётся, не делай так. 🤣
Я думаю походит и довольно долго, если бы это была вибрация то месяц Макс. Соль мороз
А тут кручение, сухо, лет с 10 как пить дать, а может и больше.
문이 열릴수록 장력이 강해지는 단점이 있지만 간이로 쓸만하네요
Good for any light weight door at size below1m x1m.
Liked your video subscribed❤❤❤❤❤❤❤❤❤❤
Дорогой давай купим доводчик ? -У нас есть доводчик дома
🤣🤣🤣
А вот у одного изобретателя очень туго открывалась входная дверь. Когда его спросили, почему дверь так туго открываются, он сказал, что при открытии воды из колоца откачивается на поверхность 8.5 литра воды. Его спросили: а почему именно 8.5 литра? Он ответил: К сожалению дамы при большем количестве воды не в состоянии открыть дверь!
😅🤣🤣😆 te mamaste.
, евреи они такие))))
This is one part of making a spring lock from scratch instead of intradural
Masya'allah idenya ❤❤❤❤
Интересная конструкция! Но, пружина скорее всего-отломится!!
Не скорее всего, а наверняка. Просто варить легированную сталь, не самый умный поступок. Есть гепростые способы, но это не тот случай.
Да блин почему все больше материала для доктора Дью начало попадаются в рекомендациях 🤣
потому что доктор всё реже и реже стал разъёбывать таких мастеров
Bruhhh, lol 🗿
Да тут и ежу понятно что варить пружину хреновая идея
250
This is @MrNik01 .
I don't understand
Love it😍
C’est excellent pour l’explication 👍