ooooOOOOO SSSSuuuummm dude !!!!! Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not .. But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ... But people told that kid , that his idea was not implementable ...
That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.
@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.
No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊
Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛
Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda
Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”
while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
Rangkaiannya Keren Banget.. hanya saja kalau kita mau Menambah Potensio sebagai Penambah pengaturannya bagaimana Merakitnya..? ok Terimakasih atas Konten nya, Keren Banget jadi Menambah ILMU.. ☺👌👍
Hahahahah Don't be fooled guys. that thing he claims to be a battery has a bluetooth player inside. The audio is actually coming from the media player inside the fake battery. Look at his connections, the red terminal in connected directly to one side of the speaker and the other terminal to the mosfet which I suspect has a short circuit ot the resistor connected to the mosfet case has a short or a wire was put through it to complete the circuit via the heat sink.. Also check when he puts the fake battery down you can see that it is light weight. I would have expected a battery of that side must have some weight . All his videos are fake.
I can test this arrangement with some caveat. So that there was audio output I had to connect the drain from the mosfet to the gate through the 10K resistor. Instead of connecting gate to source. The result was not 1300 W. I think it was much less than the speaker used 8 ohm for 60 W. The mosfet gets very hot.
Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai th-cam.com/video/HGtOfyjRcIk/w-d-xo.html
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing
no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.
You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)
Bom mas esse padrão Rabo Quente na saída, acaba por distorcer os médios. Tenho vários projetos assim e se não for instalado um bom filtro, distorce mesmo.
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta. Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante. Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.
Sar mere pas 7294 2ic apliphyr hai or 2'10inch155megnet spikr hai or osme muje 500wat sbwoofr or lgana hai to konsha bord lun or konsha s.b.filtr lun or konsha transformr lena h plis btana
Can we use it for long time use What will be the minimum power of speaker that can be connected with the circuit and maximum power of the speaker up to which it can amplify the sound Is it a stereo amplifier circuit?
@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada. Es de lógico que ese circuito no puede dar tan alta potencia. Gracias
Hmmm... Really very powerful... Had that thing measured 5watts? Unbelievable... Even the laws of Ohm and power formulas are not what they have been 😳😳😳😂😂😂
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
Has anyone tried this? I would imagine that the battery is 12v and probably 10Ah. I would like to see him runs a voltage test on the battery to show us that there is no amp inside it. I will try this in the near future and get back to you.
*DIY Powerful Ultra Bass Amplifier SSD Computer , No IC , Simple Circuit* th-cam.com/video/PVN2iqXv5kg/w-d-xo.htmlsi=jPtXuJCVo-xog2hT
Oye y si kiero k levanté unas 4 bocinas d esas omas grandes Sele ponen más integrados d audio
ooooOOOOO SSSSuuuummm dude !!!!!
Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not ..
But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ...
But people told that kid , that his idea was not implementable ...
Excellent!!! your are making an advertising for Microsoft surface too!
This is a Class A amplifier, output is approx. 2.5w with 12v power supply.
That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up.
My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.
@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.
No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊
Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W
Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛
hahhahahahhhhaa 4,5? 1w max
Hola, y como se calcula la ganancia de este circuito?
Hesap çok iyi
I am sure that it is at least 10,000 watts 🙂
Edgar y como se hace si quiero colocarle otro speaker ? gracias
This is more like art than electronic achievement
Excelente saludos desde Metán Salta Argentina
GRANDE GRANDE GRANDE, MARAVILLOSA APORTACION PARA EL MUNDO,GRACIAS.
Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda
Una pregunta.... la caja azul es una batería y de que capacidad
@@JoseRamirez-xc9dg es 12 v es la batería que usan las alarma
Nice video sir 👍🏻👍🏻👌👌👌👌👍🏻👍🏻
Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”
@ Technical DIY How can you say 1300 W? But are we sure? What calculation did you apply?
what voltage and watts do you use as a power supply?
Batrainya berapa volt
Galing na man salamat sa pag share ng talent mo bro
Try to use F-CK69 Gaetanium transistor, it will give 10.000W or how much you want. Don't forget to use Shitanium filter caps for output.
what are the filter caps for?
🤣😂🤣😂🤣
Jajajajaja
Done is more than the perfection!
while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
1300PMPO possible 😅 lol
Cred că depinde mult și tensiunea de intrare ( semnal )
@@juliusortaleza1486in PMPO everything is possible.🤷🏻👍🏼
1300w PMPO
GRACIOSO,,, sale la polilla por abajo del discipador justo cuando arranca el riser or filter de la música del video
🤣
God work. ..and easily to make. .thankfully
Good tiching karte hai 👍👌👌👌👌👌👌👍👍👍👍👍
Я в детстве тоже усилители собирал,только маркер тогда ещё не был в ссср,а так бы я нарисовал ,что у меня динамик10гигаватт
Good job friend 😁👍👍
That's like 1 watts at maximum, 1300w would blow that speaker it would be bottoming out really hard smoke and blow, lol
wah praktis ,menggelegar basnya 👍
1.300w? Or 13w?
13 w 😁😁😁😂😂
This amplifier delivers only 8w
Rangkaiannya Keren Banget..
hanya saja kalau kita mau Menambah Potensio sebagai Penambah pengaturannya bagaimana Merakitnya..?
ok Terimakasih atas Konten nya, Keren Banget jadi Menambah ILMU.. ☺👌👍
En la caja de descripción pude observar por lo menos 2 mentiras: 1300W y Hi-RES. Haces buen trabajo creando pero por otro lado no mientas.
Si si es verdad, lo le dije son 1300 Watts de consumo, va ni eso, 1300 Watts RMS jamás puede ser 😀👍
Kembali lagi sperti biasa, ini ter kongkrit bagus jleger bom.. wow amazing
Great work. So much views. 1300W is not a joke.
use Ohms Law it is IMPOSSIBLE here to get 13000W
Mantab terimakasih atas ilmunya semoga sehat selalu aamiin. Bang
Hahahahah
Don't be fooled guys. that thing he claims to be a battery has a bluetooth player inside. The audio is actually coming from the media player inside the fake battery. Look at his connections, the red terminal in connected directly to one side of the speaker and the other terminal to the mosfet which I suspect has a short circuit ot the resistor connected to the mosfet case has a short or a wire was put through it to complete the circuit via the heat sink..
Also check when he puts the fake battery down you can see that it is light weight. I would have expected a battery of that side must have some weight .
All his videos are fake.
that's true ! wires are directly to speaker, we all can see at 8:00
thank's for hint !
nice lol, I thought it was legit until he wires the audio out to both sides of the power resistor, couldn't see how that would achieve anything.
Tengo todo el material pero en verdad funciona?no quiero perder el tiempo
@@ash0787 lolw, mine is under construction :)))) i use 5kg transformer :)) at 20volts :)))
I can test this arrangement with some caveat. So that there was audio output I had to connect the drain from the mosfet to the gate through the 10K resistor. Instead of connecting gate to source. The result was not 1300 W. I think it was much less than the speaker used 8 ohm for 60 W. The mosfet gets very hot.
Классный музон💥🔊🥁🎶
I like these simple designs....very easy to build for beginners. But 1300watts with a single fet from a 12v battery.....that's impossible.
Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai th-cam.com/video/HGtOfyjRcIk/w-d-xo.html
Just try and you can tell💪
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
Mantap ide kreatifnya bang👍
How much is the output watt ?
How much power and Ampier should I give?
1000000v or fack
❤❤❤❤❤❤ what a great help!!!!
Wtf? My Peavey Max amplifier had 24, 150 w Darlington power transistors in it, and it was 400 Watts per channel RMS.
Ang galing mo talaga idol gawa mo ako nyan
Gostei 👏 parabéns ficou show de bola 👏 obrigado.
I’m glad if u can fix the speaker on box. So everyone can hear the bass far better
And not just that if the title of the video is in English at least and English song as well..
@@ricardojuarez291 yup. More enjoyable the diy project.
Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing
th-cam.com/video/HGtOfyjRcIk/w-d-xo.html watch video about Ak amp
no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.
If you are interesting in electrical engineering do yourself a favor and dont watch these videos, there are much more credible sources elsewhere
Mạch công suất âm thanh bé mà khỏe phết của nhà nhỉ
this small speaker is 50w and this amplifier is 20w max
Не 50,а 5-10 от силы но чуйка возможно не плохая😅
@@あなたはここで何を見たいですか 10w speaker is printed. on magnet
You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)
Мужики,вы меня дурите😄
@@paolbackman651 anyone can write 500W on a speaker, more likely a 10w speaker, freeze video where he's waving the speaker about 6min.50s
What u have used in the end ..that something similar like iron plate
Impressive for such a simple circuit
4:37 даже таракан🪳🪳🪳 сделал ноги 🤣🤣🤣🤣
Bom mas esse padrão Rabo Quente na saída, acaba por distorcer os médios. Tenho vários projetos assim e se não for instalado um bom filtro, distorce mesmo.
Como fazer o filtro com potenciômetro?
Hello, thanks, I made it like you, the sound is very weak??
With this single ended drive, the max power output can be easily predicted by the supply voltage and speaker impedance....
Can i use this circuits for boost dc volt?
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up.
My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
What ever happened to good old schematics and parts lists? It would nice to include a shot of the circuit for us old school guys. Nice video though!
Cara!meus cinseros parabéns pela excelente qualidade do seu vídeo. Parabéns!!!!
Good idea i like 👉🎬
Can use potensio for increas or dicreas?
3:18 I olmost died by laughing at this point 500W ;D omg hahahahaha
Congratulations blessed ball show stays with God hugs
ขอบคุณครับ. หาของเจ๋งๆมาให้เล่น เบสสุดยอด
Est ce que cet amplie na pas de parasites!????
Ребят когда он показывает динамик посмотрите там 10 ватт 8 ом😂
Mantaaap bang.bisa buat jual di pasaran ni..di toko toko udh ada blm bang hasil karya nya
How would you remove humming sound while conducting to transformer Ac-to-Dc ?
Simple tested solution
Connect 1uf poly cap between audio input + and ground.
Where does 1300 Watts come from, if such an irfz44n dissipates a maximum of 94 watts?
4.36 из под радиатора выбегает таракан аудиофил))))
😂
Beau travail, merci pour le partage. Félicitations du Maroc 🇲🇦🇲🇦🇲🇦
Será que pode usar uma fonte de 12volts ao invés da bateria?
Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta.
Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante.
Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.
@@ramos3246 será que vira testar em um carro?
essa bateria é de 12volt 12 amperes
Excelente,pero vieras metido la bocina en una base o una cubeta de agua para ver que tal el sonido encerrado.saludos desde Campeche,Mexico
Muito massa...ganhou mais um inscrito 👏👏👏👏👏
Agar yah savan to dikha rahe hain aap vah bajega nahin to
excellent video I see what you do congratulations hand up
cara gostei muito, só que a ligação do falante está invertida né? batendo pra dentro , o certo é para fora
Esse alto falante ai 500w😏
Mantap, tp g dijelaskan pasang mosfet ke heatsink perlu isolator apa g, & besaran voltase ACCUNE jg g dijelaskan
fala sério nunca daria essa potência toda..
Kkk né isso kkk
Deve ser esses cara que fazem os mini-Sistem das casas brazoca hj em dia kkkkk. Consomem 10w e reproduz 1300w
@@adrianocordeiro8643 kkkkk Nem classe D com 90% de aproveitamento kkk
C'est impossible, mais possible pour vous, je vous aime et je vous remercie 🙏🙏
muy buen video bien esplicado me gusta la electronica y me gustaria aprender
Sar mere pas 7294 2ic apliphyr hai or 2'10inch155megnet spikr hai or osme muje 500wat sbwoofr or lgana hai to konsha bord lun or konsha s.b.filtr lun or konsha transformr lena h plis btana
Can you make a video for making amp for using guitars pls
how much powwer we need to give it it's glowing on if we give 12 or much higher volt and current
Mas, valeu o vídeo, me lembrando aqui qdo trabalhava na ind.eletronica, eu fabricava as placas de circuitos impresso.
👍👍👍 saya punya amplifier merk sunbuck suaranya normal tapi ada gak yang suaranya ada kresek2 itu apa nya ya Om 🙏
4:36 от девайса отделилась деталь и убежала . Если бы не убежала мощность была бы 13000W . 😄😄😄
китайских Chines 99999999 WATT
Какой-то лютый треш😂😂😂
Просто убираем нолики и тогда по честноку всё будет))
13 Ватт с КНИ-10%.
Это тараканы разбегаются
Can we use it for long time use
What will be the minimum power of speaker that can be connected with the circuit and maximum power of the speaker up to which it can amplify the sound
Is it a stereo amplifier circuit?
Maximum input voltage of this circuit?
От 12 вольт как то попахивает вранье
Да неа, вполне рабочий вариант. Только качества звука желает лучшего
При 12 вольтах? 1300 ? КПД-1000%-прорыв в физике,понятно,что у них другой "ГОСТ".
keren pokoknya. 👍👍
Congratulations... excelent!!!!!
👍👍👍👍👍👍👍👍
REPÚBLICA 🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷ARGENTINA
Excelente, buena calidad de sonido. Muy económica y eficiente.
neeee este video es muy falso
@@manu-06 porque???
@@juliopena2336 no existe un amplificador clase a con 1300 watts ._.
Este proyecto a lo mucho 12w
@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada.
Es de lógico que ese circuito no puede dar tan alta potencia.
Gracias
Dah nyoba gak bisa keluar suaranya
Nice share..
Amazing 👏👍👍
Hmmm... Really very powerful... Had that thing measured 5watts?
Unbelievable... Even the laws of Ohm and power formulas are not what they have been
😳😳😳😂😂😂
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
Merci beaucoup !!!!!!!
❤❤❤❤❤❤❤
RMS 5W? :-)
Esta en avalancha toda la potencia se va al parlante pero de seguro se te quema facil necesitan mucha proteccion a no ser que tengas bocinas de sobra
4:37 помощник выбежал😀
Excelente amplificador, gracias..!
Ati te funcionó??
@@luisdamianduran2744 Saludos, aun no lo he armado aunque tengo todos los componentes.
@@carloszambrano3227 noooo bro no te da 1300w
A lo mucho 10
@@manu-06 eso es correcto, no más de 10w.
@@carloszambrano3227 ci y además un amplificador clase a no puede pasar los 30w
Hola. Donde conectas la corneta, la caja verde que es.... Y donde va el positivo y negativo del cable jaks.. No lo dices..
Sir, please make this circuit in the supply of three faces please
Glad you found an amp to go with your 500W speaker
Parece ser tão simples de fazer
Has anyone tried this?
I would imagine that the battery is 12v and probably 10Ah.
I would like to see him runs a voltage test on the battery to show us that there is no amp inside it.
I will try this in the near future and get back to you.
Hello, I wanted to ask you, have you assembled a circuit, does it work, how many amps does it consume?
@@ГеннадийМ-ь9ш Hi, thanks for reaching out. No I haven't had the time but I will let you know how it goes. Thanks!
@@irawardmusic thank you, I will wait for an answer from you!
Projeto muito bom gostei
Nossa passou uma barata? Rs
Siiii, también la ví
ওয়াও বিউটিফুল
Spk nya 500watt brpa in bang ?
Yes, this a great design from 5W heatsink... Probably can output ~1W (maybe 1300 milliwatts?!) of power with huge distortion... HaHa...
FICOU BATENDO PRA DENTRO MAS FICOU ÓTIMO...
Amazing video