ฝัง
- เผยแพร่เมื่อ 1 ส.ค. 2024
- Important: 25min 40sec white gears position.
Remove the brown sponge from the solenoid and glue there a thin plastic piece.
CM4540 is very similar.
UPDATE!!!: I found an other video about this issue which is much more simple: • CP3525 Tear-down to 59...
I haven't tried it in that way, but you should.
Hi,
Thanks to your video, my printer is fixed !! I just removed the foam and the problem is gone .
Cheers !!
Omg! thnx bro, finally this video saves my spinning day, I hardly understood the language but still, I followed the steps and fixed the ERROR 59.F0 on a CP4525, obligado parabens !!!!
Thanks for the disassembly of this area, I get to replace the fuser drive in one today :-(
Thak you! I had error 59.00.F0 on a CM4540FKSM and I had no idea what could cause it. After I saw your video I found that solenoid on my printer, cleaned it, and the error is gone, so this fix works on CM4540 as well. Of course it took me the whole day to do it :))). Thank's again!
Is the disassembly and reassembly procedure similar or same?
Not quite the same, but after you remove the scanner and the top side, the procedure is very similar. Most of the parts are in the same place, but you have a few extra things because you have the scanner.
Thank you for your feedback. I have modified the description.
Thank you for this video!
Obrigado... Foi de grande Ajuda!!!
thank you very much for information. Hi from Lima Perú.
thank you for this video! obrigado parabens ! - brasil
Gracias
Спасибо за видео,вы помогли мне
This is very helpful vedoo
Thank you
Good job
Ce très intéressant ça me donne un plus 😮
Machines less complex than this printer took man to the moon...
بفضل الله بحل المشكلة دى ف ساعه بس
السلام عليك اخي ان لدي نفس المشكله ماهو الحل شكرا
good morning I have a question, I have an hp cp4525 with faults in the page counter, she counts them when I print them and after I turn off the printer and turn it on she subtracts the pages already printed from the counter, you know what is happening that? do you have any solution for that failure?
This video proves you don’t have to remove the main drive or the lower high voltage board
Tank U
Unless, of course, from the .001% chance it is actually the Fuser main drive assembly.. oi.. good video
Hi I have a m452dw printer that has the same error 59.f0 do you think applying the piece of tape on the solenoid would fix it?
No i think. M452dw is young yet. The "sponge error" come about min. 4-5 years.
buenos dias tengo una duda, tengo una hp cp4525 con fallas en el contador de paginas, ella las cuenta al momento de que las imprimo y luego que apago la impresora y la enciendo ella me resta del contador las paginas ya impresas, sabes xq esta pasando eso? tienes alguna solucion para esa falla?
Thanks for your video, it really helped me with many printers i've had paralyzed because of this trouble. But i have a question: Can i left the solenoid without that tiny sponge? Thanks again.
No, you have to glue there a thin piece of plastic.
On a solenoid. You can never have metal to metal contact, or magnetization will occur. Replace the foam pad with proofing material like felt, or slip 3:8” shrink wrap tubing over the foam pad lip. You’ll never have this problem again.
like, bro!
hi, i remove the brown sponge from the solenoid and glue there a thin plastic piece and the printer have a 52.00 error, do you know what error it is?
52.00: The scanner has experienced a startup error.
Check the following connectors: J501, J503 on the laser PCA and J106, J110, J111 on the DC controller PCA
Hi, I will need to do this on the CM3530 MFP (Printer/Scanner/Copier) version of this machine, how complicated is it to remove the scanner/control panel top, or is it necessary to remove it for this repair? Also why is the power supply removed? It does not seem to be in the way, Thank you
It is necessary to remove the scanner, but I don't know how complex it will be. In connection with the PS: I don't remember exactly because it was 4 years ago when I made the video, but I think it was necessary to remove it.
Thanks for this movie. i have a CM3530 printing fine on USB but cannot connect it via LAN, win10 dose not recognize the LAN. The cable is fine, ip4 is fine. possible the formatter board needs to replace?
Yes, it is possible, but usually defective formatter boards cause other problems not that one.
1. Connect the printer to an unmanaged switch or router. If the port led goes on than the link is OK.
2. Try to check the layer 2 communication. I use Lantronix Device Installer. You'll see if it is OK. (Your computer's connection needs to be OK.)
3. If the first two steps are OK than you have a layer 3 problem with IP settings.
You can try a factory reset on the printer, but sometimes it can cause other problems.
bonjour tous le monde, c'est très util cette video, est ce qu'il y a quelq'un qui a un cite où puis-je acheter ce solenoide sur internetc'est urgent merci
This is an absolute nightmare, how am I supposed to do half the steps on the mfp version??.
Can this be done without removing the psus or so many components?
Did you end up doing it? I have to do it on the MFP version too.
@@aabsc no, never got the time and space to do it, it's on the eternal "to do"
Hello ! I followed the instructions in your video about error 59.F0 (CP3525) , I removed the sponge. After assembling back the printer I get an error 59.30 on the display. Any tip ? Help !
Check J117 connector on DC controller. Check fuser motor rotation.
Thank you !
Hi, I finally got to replacing the entire fuser drive assembly but when I took apart the old one the solenoid doesn't seem to stick, does this mean that wasn't the cause of my 59.F0 error or does the sticking not have to be noticeable to cause the error? If it sticks it's for a fraction of a second and barely noticeable, is that enough to cause an error? Thank you
Yes, because it works repeatedly and the time period while it sticks became longer and longer.
@@scrwdrvr It fixed it! Thank you th-cam.com/video/NW4UA_4HQNI/w-d-xo.html
I replaced the whole fuser drive assembly but now get a 55.01.00 DC Controller Memory error. I've replaced the DC Controller board - still get the error. I triple checked all the connections on the board AND behind the High Voltage Power Supply (upper) - nothing is disconnected. I replaced the DC Controller again, still the error. Any ideas on this?
I haven't got any specific hint. But: was the first 55.01.00 appearance after you changed the fuser drive? If yes, then you should search the reason where you "walked" during the replacement.
@@scrwdrvr Thank you for the reply, but I'm not sure I understand what you mean by "the reason where you walked during the replacement". Right now, the printer is sitting disassembled up to 19:18 on the video . I didn't go further, because I just wanted to make sure nothing was left disconnected (it wasn't). And yes, that error made it's first appearance after replacing the fuser drive. So I replaced the DC Controller board (twice!) but it didn't make any difference, so I'm guessing it ISN'T the DC PCA.
Thanks again, and please let me know what you meant.
@@hitmanbluesband I'm affraid that the error was caused be the repair process. A loose groud wire, two interchangeable cable, a poor contact can cause an inexplicable error. You right, the DC PCA is likely OK as before.
hello, thanks. i did mine but afterwards i have an error: imcompatible fuser. kindly help.
Hello, Check the connectors between the fuser and the pcbs.
thanks but now I've 52.0 and I can't locate J501, J503 at all. where can I find it on the machine pls?. any kind of help would be appreciated. thanks
First check J106, J110, J111 on the DC controller PCA.
thanks! works fine now.
Part number for this unit?
Fusing (fixing) drive assembly with motor (duplex) RM1-4974-000CN
Fusing (fixing) drive assembly with motor (simplex) RM1-5001-000CN
Is it the same as HP LJ 500 color?
Very similar I think. Watch this video: th-cam.com/video/m52QQRJEHfQ/w-d-xo.html
Hi there! I have the same printer (HP Color LaserJet CP3525n) with the same error (59.F0 error). We first thought that the problem was the ITB, we already ordered and replaced the ITB with new one, but still have the same error, and I also hear a noise inside the printer. Do you think it is necessary to replace the white gears and the solenoid, or there is another way to fix this printer? Thank you in advance for your help. By the way, great job!
Hi! I think it's enough when you remove the brown sponge from the solenoid and glue there a thin plastic piece. Pay attention white gears position!
Thank you VERY MUCH. I finally get the solenoid out of the printer, very difficult! Can you tell me what kind of plastic should I use to fix the problem? And what size? 1 millimeters or 2 millimeters? Maybe thicker? And what about to test the solenoid outside, how can I be sure that it is working fine? Thanks again!
Never mind, 1mm or 2mm is ok. If you cleaned the sticky area then it will work fine.
apparently mine still showing the same error after applying the plastic it wont boot past 59F0 error...
new fuser kit by the way...
There is NEVER a reason to have to take the LVPS out to repair this error, nor disassembly of the DC controller board.. 30 minutes in and out, from power down to start to power up to test..
This is for a transfer belt solenoid in the comment above..
esa misma falla la este modelo también si tienes la solución a esa falla me ayudarías mucho elgato9_15@hotmail.com si encuentras una solución avísame
kár hogy szar a felbontás, lószart se látni :(
A szervizkönyv sokat segít a video mellé, érdemes letölteni.
Thank you