I power them both with the 529hc and a daisy chain cable. Mission engineering sells a 2.1 to 2.5 adapter which is needed for the hx stomp. Hopefully, I’ll do a video soon explaining that more in detail.
Are you in Toggle mode to do the FS/snap combo? And using the FS for a block bypass? I’ve been trying to set mine up with something similar but using toggle mode for block bypass then makes the block need another press and release before it functions correctly after I’ve changed a snapshot.
There’s a setting for snapshot recall or discard. One allows you to change snapshots and keep the settings that you’ve made by turning off the block, the other allows you to change snapshot and they’ll load the way they were saved last.
When you are controlling reverb with the expression and you change to volume, does the value in reverb stays the same as you leave it? ( for example halfway)
Yes, when I change from delay/reverb to volume, the previous setting stays the same and can’t be changed until I press the button on the mc3 again then move the expression pedal again.
Yes, I use the expression pedal to control various parameters on a block or set of blocks. Instead of using the midi code for the expression pedal on the stomp, I use an empty code and use midi learn on the stomp.
You have to set up either foot switch 4 or 5 to toggle between the two expression pedals, then use the midi command for that foot switch (cc 52 fs4 or cc 53 fs5) to toggle them via midi
If you’re in the US, here’s the link: www.gearbyceba.com/line6-family-usa/hx-touch-enabled-foot-switch-toppers-magnetically-attached-usa If you’re outside the US, here’s the link: www.gearbyceba.com/line6-family-international/hx-touch-enabled-foot-switch-toppers-magnetically-attached-int
@@MauricioBond23 unfortunately not. The first generation would as they screwed on the button. The current evolution magnetically connect which doesn’t work on the MC3.
Finally somone using the MC3 with HX STOMP. Thanks for sharing. I was wondering, i know the hx is limited to 3 snapshots but, imagine you need more than 3 snapshots, could you use presets instead ? Considering you have now 6 fs thanks to the MC3, could you have 6 differents presets directly accessible under your feet ?
you can't change presets instantaneously, so there will be a short interruption of the audio. but yes you can change presets on the stomp via midi. i don't know how many midi ccs the mc3 can send at once. but in general, you can assign a midi cc to any block of your preset and then switch blocks on/off. So you need to do more programming on your midi controller, but this is a workaround to get "more snapshots".
Gearbyceba.com the ones on the mc3 are version 1 toppers that are no longer made. The current ones are magnetic, which will fit the stomp just fine but not the mc3.
Something you can recomend me to start learning about MIDI? It’s has been always hard for me because im not pretty good with computers, i record with portastudio and old stuff
![The Wall Song ร้องข้ามกำแพง | EP.215 | พาเวล นเรศ - พูห์ กฤติน | 17 ต.ค. 67 [1/5]](http://i.ytimg.com/vi/IUzrjuf60P4/mqdefault.jpg)
![⭐ฮิตในTikTok!! ( มะมะมะหมูเด้ง MooDeng ) Ver. แดนซ์ ReMix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/4noyAoMa7bQ/mqdefault.jpg)
Great video. Are you powering the stomp and the MC3 both with the same 529HC? If so, how do you do that? What cable do you need? Thanks!
I power them both with the 529hc and a daisy chain cable. Mission engineering sells a 2.1 to 2.5 adapter which is needed for the hx stomp. Hopefully, I’ll do a video soon explaining that more in detail.
@@DefconClark thanks!
Hi, what cable do you use to connect the mc3 to the volume pedal? Is it a regular patch cable? I would greatly appreciate your help.
You’ll need a trs to trs patch cable.
Thank you so much.
Thanks for this overview. I've been considering the MC6 for my Stomp rig but the MC3 would seem to be entirely sufficient for less cost.
Good deal
Hey man where do you get the pedal toppers from?
What is that bluetooth midi thing that you're using? I couldn't quite understand what you said.
It is the CME Widi Master. I have some videos about it on my channel if you want to check them out.
Are you in Toggle mode to do the FS/snap combo? And using the FS for a block bypass? I’ve been trying to set mine up with something similar but using toggle mode for block bypass then makes the block need another press and release before it functions correctly after I’ve changed a snapshot.
There’s a setting for snapshot recall or discard. One allows you to change snapshots and keep the settings that you’ve made by turning off the block, the other allows you to change snapshot and they’ll load the way they were saved last.
When you are controlling reverb with the expression and you change to volume, does the value in reverb stays the same as you leave it? ( for example halfway)
Yes, when I change from delay/reverb to volume, the previous setting stays the same and can’t be changed until I press the button on the mc3 again then move the expression pedal again.
Itching to get one of these. Really dig your videos
Great video! Where are you plugin the expression pedal in? Can you plug it into the mc3 and that way control the stomp? Thanks!
Yes, I use the expression pedal to control various parameters on a block or set of blocks. Instead of using the midi code for the expression pedal on the stomp, I use an empty code and use midi learn on the stomp.
Could you share your midi settings? What CC are you sending to toggle between expression 1 and 2?
Second this! Would really like to know too
You have to set up either foot switch 4 or 5 to toggle between the two expression pedals, then use the midi command for that foot switch (cc 52 fs4 or cc 53 fs5) to toggle them via midi
Hi, amazing video. May I know what cable do you use for powering the hx stomp and MC3?
For that video, I believe I used a daisy chain from the 529hc
What board is this? The Nano?
Nano plus
Hi there, super helpful, thanks! Which toppers are those? Thx
If you’re in the US, here’s the link:
www.gearbyceba.com/line6-family-usa/hx-touch-enabled-foot-switch-toppers-magnetically-attached-usa
If you’re outside the US, here’s the link:
www.gearbyceba.com/line6-family-international/hx-touch-enabled-foot-switch-toppers-magnetically-attached-int
@@DefconClark thanks 🙌🙌🙌 (those will not work on the MC3 though right?)
@@MauricioBond23 unfortunately not. The first generation would as they screwed on the button. The current evolution magnetically connect which doesn’t work on the MC3.
Does it have start stop features for a drum machine? like an analog rytm by elektron?
I’m sure it can if the device you want to control accepts midi.
Finally somone using the MC3 with HX STOMP. Thanks for sharing.
I was wondering, i know the hx is limited to 3 snapshots but, imagine you need more than 3 snapshots, could you use presets instead ?
Considering you have now 6 fs thanks to the MC3, could you have 6 differents presets directly accessible under your feet ?
you can't change presets instantaneously, so there will be a short interruption of the audio. but yes you can change presets on the stomp via midi. i don't know how many midi ccs the mc3 can send at once. but in general, you can assign a midi cc to any block of your preset and then switch blocks on/off. So you need to do more programming on your midi controller, but this is a workaround to get "more snapshots".
Yes, but there is no spillover so there will be a slight audio gap.
Is it possible for the morning star to draw power from the HX stomp via usb?
Unfortunately, I don’t believe that’s possible.
What are these pedal switch toppers ?? Can I have a link ? Great video
Gearbyceba.com the ones on the mc3 are version 1 toppers that are no longer made. The current ones are magnetic, which will fit the stomp just fine but not the mc3.
If the MC3 only has Midi Out how are you able to control the Hx stomp, you don´t need a midi in?
Nope, the midi out of the mc3 goes to the midi in of the stomp and controls it that way.
@@DefconClark Thanks!, Definitely considering buying it.
How do you like the MC3 compared to the JET?
The jet micro is great for a preprogrammed midi controller. I, however, wanted a bit more controllability, expression port, and bigger footprint.
Super useful, thanks for sharing ! Anyone here nows if it's possible to achieve similar results with a midi baby disaster 3 ?
I’m sure you can achieve similar results with the midi baby. It would be cool if I could get ahold of one to try out for you.
Good stuff
Thank you!
Something you can recomend me to start learning about MIDI? It’s has been always hard for me because im not pretty good with computers, i record with portastudio and old stuff
@@ap210482 check out my friends channel. He’s very technical and helpful.
th-cam.com/users/AlecBourneMidiMadScientist
Nice board
Thanks
wireless midi would freak me out ;)
It’s different for sure