No. It will leak and come apart. Some people use screws and glue but really it's the glue that's holding it together. Screws just keep it together until it can dry
I'm pretty handy and can build just about anything. I've found pre built boxes but I'd like to build my own. I have a 2017 f250 and have six 6.5 ct sounds meso subs. Do you sell or offer any type of drawings or cut lists. Thank you
Hi, I'm French so it's complicated for me to understand your videos. I would like to make a dual subwoofer for 2 SR124DVC subwoofers. But I found conflicting information for 1 box with 1 single subwoofer, so I'm afraid my calculations are wrong for a box with 2 subwoofers. How much should my box be in volume to have a good result? I'm worse than a beginner in it, and with the information I found I got 105.07 liters. Is it good enough? I intend to lock them in the membrane box downwards magnet upwards with 2 vents on each side which go to the center with a plexiglass plate at the top to close. Is it a terrible choice? Basically, plexiglass at the top, plate 2/3 below the middle which houses the 2 subwoofers upside down, the vents and the bottom plate. Like my Caliber BC112EB . I hope to get an answer from you. I've been looking for a way to do this for a while.
Do you really need to double up on the 3/4" baffle for a 300w speaker? I have two 12w3s on a single layer 3/4" baffle and can't feel any vibration from it. Should I remake my box?
He did that for cosmetic reasons. The woofer is recessed and not screwed or bolted through the outer layer. 3/4" MDF is sufficient for this power level and weight of the driver used.
LxWxH lol jk, there's lots of free programs that allow you to put those measurements in and it accounts for the material thickness and will give you a rough estimate of that interior air space. compare with other programs tho because they're not all exact like, I modeled my sub in winisd, which is more for tuning an enclosure and less about actual enclosure measurements. but it does give port length and you can play around with that and the internal air space, then on sub box pro, some free online site I used to calculate air space.... I wanted 8.5 cubic foot so when I got the box to that size in sub box pro I compared the port length to that of the length in winisd and made adjustments in sub box pro until the specs were the same. this probly makes no sense and it's exactly why mark didn't give a clear answer lol. it's too much to answer without a whole lesson being preached but to add on to what Mark said, it'd be better to be too big cuz you can always take air space away, you can't add it back in 🤓
Unless the customer wants something legitimately custom for their car and sub, you wouldn't even come close to being able to compete with prefab box prices. I just bought some of the material for building a box for one 10". MDF, Titebond III, and spray adhesive were almost 100 dollars. Haven't got any carpet yet, terminal, polyfil. Idk what that stuff will jack the price up to but then also you gotta make money on the labor or it's not worth the time. Unless you know someone who wants to pay 400 bucks plus for just the box. And with the amount of time you'll spend to build it it's not lucrative at all. But if you just like to do it and it puts an extra 100 or 2 in your pocket then it's fun and rewarding.
Jl is not budget build
When you said in less than a minute I thought for a second you were just going to cut a couple holes into the speakers box and wire it up lol.
buahahaaaa
He said budget, then I saw JL Audio.... mans got a big budget
It's their entry level subwoofer. Extremely affordable.
I had a 15" sub in my MK1 escort GT way back in 1988
What router table do u use and I want the same set up for router adjustable top
Amazing what you can cook up in the kitchen
Do a whole kicker build
Can i use a nail gun or heavy duty staple instead of glue?
It will come apart when the subs get deep
No. It will leak and come apart. Some people use screws and glue but really it's the glue that's holding it together. Screws just keep it together until it can dry
I'm pretty handy and can build just about anything. I've found pre built boxes but I'd like to build my own. I have a 2017 f250 and have six 6.5 ct sounds meso subs. Do you sell or offer any type of drawings or cut lists. Thank you
What is a budget subwoofer
Where can I purchase your enclosures?
$510 MSRP for the sub/amp combo is a BUDGET build? Man, I must be really cheap then LOL
Oh ya... I can do it in 48 seconds, so take that Mark.😎
Hi, I'm French so it's complicated for me to understand your videos. I would like to make a dual subwoofer for 2 SR124DVC subwoofers. But I found conflicting information for 1 box with 1 single subwoofer, so I'm afraid my calculations are wrong for a box with 2 subwoofers. How much should my box be in volume to have a good result? I'm worse than a beginner in it, and with the information I found I got 105.07 liters. Is it good enough? I intend to lock them in the membrane box downwards magnet upwards with 2 vents on each side which go to the center with a plexiglass plate at the top to close. Is it a terrible choice? Basically, plexiglass at the top, plate 2/3 below the middle which houses the 2 subwoofers upside down, the vents and the bottom plate. Like my Caliber BC112EB . I hope to get an answer from you. I've been looking for a way to do this for a while.
Do you really need to double up on the 3/4" baffle for a 300w speaker?
I have two 12w3s on a single layer 3/4" baffle and can't feel any vibration from it. Should I remake my box?
He did that for cosmetic reasons. The woofer is recessed and not screwed or bolted through the outer layer. 3/4" MDF is sufficient for this power level and weight of the driver used.
He powerd it with disle
How do you work out the size (volume) of the box for the speaker and does it matter if it's too big?
Not a simple answer as there are a bunch of calculations but yes, too big an enclosure can definitely lead to poor sound performance.
LxWxH lol jk, there's lots of free programs that allow you to put those measurements in and it accounts for the material thickness and will give you a rough estimate of that interior air space. compare with other programs tho because they're not all exact
like, I modeled my sub in winisd, which is more for tuning an enclosure and less about actual enclosure measurements. but it does give port length and you can play around with that and the internal air space, then on sub box pro, some free online site I used to calculate air space.... I wanted 8.5 cubic foot so when I got the box to that size in sub box pro I compared the port length to that of the length in winisd and made adjustments in sub box pro until the specs were the same. this probly makes no sense and it's exactly why mark didn't give a clear answer lol. it's too much to answer without a whole lesson being preached
but to add on to what Mark said, it'd be better to be too big cuz you can always take air space away, you can't add it back in 🤓
very spicy 🌶 🔥 🔥
How well does making sub enclosures pay? I’m guessing it’s a “paid by the job.” Kind of thing?
Unless the customer wants something legitimately custom for their car and sub, you wouldn't even come close to being able to compete with prefab box prices. I just bought some of the material for building a box for one 10". MDF, Titebond III, and spray adhesive were almost 100 dollars. Haven't got any carpet yet, terminal, polyfil. Idk what that stuff will jack the price up to but then also you gotta make money on the labor or it's not worth the time. Unless you know someone who wants to pay 400 bucks plus for just the box. And with the amount of time you'll spend to build it it's not lucrative at all. But if you just like to do it and it puts an extra 100 or 2 in your pocket then it's fun and rewarding.
Is this crumb?
We do not have a tablesaw
But why mdf
looks delicious :D
Extra spicy
What do ya bet it actually took MUCH LONGER than a minute to build this box?! I'm pretty sure Mark is lying. 🤷🏽
Wow, nothing gets past you!
Could you do a tutorial on how to make a box for a 4 inch sub?
Bruh 4 inch can't do much
@@vtec8641 you’d be suprised, in my room I have a 4.5 inch sub and I’ve had people think it’s a 10, although I will be upgrading to a 10 soon
@@crikmtb5338 oh dang
@@crikmtb5338 well when you do upgrade to the 10" then come back and tell us that you think the 4" sounds like a 10 Lol
@@haydenpryor2494 it sounded like a 10 in my truck but the 10 sounds like a 15 now
Helli sir, plz give me a diamention for focal auditor 10 inch,RIP250p i need make 6th order encloser if u can help me🥰
No, it takes well over a minute to build even a basic box