Well done Christian - always a good idea to check the actual continuity of any replacement wire(s) - your multimeter is one of your best friends. Thank you and happy travels ("No helmet? NO WAY!").
What can i do, my scooter is showing the same messege E4 and than when i press the lever to accelerate sometimes run and sometines does not run, what cai i do?
ı change the new controller new display new cable w testing new battery and didnt change anything reason left its motor ! with new controller and display display shuts off directli and comes once like "tek" sound from motor model of e-scooter is bruno
Check the resistance of the windings, make sure they are about 6-7 ohms and they are the same. After that, check the hall sensors. Measure black with every other color, while you spin the motor verry verry slow with the tester leads on black and yellow, then black and blie, black and green. You should get a reading going from about 5v to about 0v on each sensor if you spin the wheel about 1-2cm (that is cm...)
I have the same problem. I asked the shop what it could be and they simply say to send it to them and they will see. I guess it ends with "you have to change everything" = 130€. This was the worst purchase of my life. It never worked ok since the start.
@@cristianbuga5126 After watching your video I think I will buy new cables from them and see if it works. While I still had the warranty they changed the controller, the cables, the battery and finally the problem was the motor. Less than 2 years later I have this E4 error. I'm going to try to change the cables and hope it's just that. Thank you for the video. When it gave me this error I asked them why did it happen and they told me maybe I had broken the spiral cable. When in reality it is simply they must use bad materials, because it worked the night before and the next morning it didn't. I don't do anything risky with it, nor do I fold it.
Well done Christian - always a good idea to check the actual continuity of any replacement wire(s) - your multimeter is one of your best friends. Thank you and happy travels ("No helmet? NO WAY!").
What does the yellow wire do?? And the blue and green wires what are they're roles
Green and blue are comunication cables and yellow is return pozitive if i'm not mistaking
What can i do, my scooter is showing the same messege E4 and than when i press the lever to accelerate sometimes run and sometines does not run, what cai i do?
The same he did look for a broke cable
I have etwow but it's bride for 25/h from display if i want to make the L5 i don't found it
If you want to make it go faster, cut a pin from the light sensor on top of the display, on the left side. It should go faster.
@@cristianbuga5126 do you know any factory codes?
@@r0ck3tdr1v3r what do you mean by factory codes?
@@cristianbuga5126 like changing the voltage settings 4236, 4248... (Codes in P Menu)
@@r0ck3tdr1v3r i haven't done any research in the settings
Can anyone help me i have the problema At the brake and accelerator sensor
ı change the new controller new display new cable w testing new battery and didnt change anything reason left its motor !
with new controller and display display shuts off directli and comes once like "tek" sound from motor
model of e-scooter is bruno
gas throttle and brake is working well
Check the resistance of the windings, make sure they are about 6-7 ohms and they are the same. After that, check the hall sensors. Measure black with every other color, while you spin the motor verry verry slow with the tester leads on black and yellow, then black and blie, black and green. You should get a reading going from about 5v to about 0v on each sensor if you spin the wheel about 1-2cm (that is cm...)
الصورة غير واضحة تماما وكذالك الموسيقى مرتفعة لم يفهم من هو السلك ...
I have the same problem. I asked the shop what it could be and they simply say to send it to them and they will see. I guess it ends with "you have to change everything" = 130€. This was the worst purchase of my life. It never worked ok since the start.
Sorry to hear that...The one that I fixed, works perfectly fine
@@cristianbuga5126 After watching your video I think I will buy new cables from them and see if it works. While I still had the warranty they changed the controller, the cables, the battery and finally the problem was the motor. Less than 2 years later I have this E4 error. I'm going to try to change the cables and hope it's just that. Thank you for the video. When it gave me this error I asked them why did it happen and they told me maybe I had broken the spiral cable. When in reality it is simply they must use bad materials, because it worked the night before and the next morning it didn't. I don't do anything risky with it, nor do I fold it.
MUSIC TOO LOUD for the level you are speaking at making this hard to watch AND listen :(
Noted. I will try to be more carefull when editing.