*It’s: Pretty. Quiet. **Fastly.Cool** in my room. Works wellLittle of hassle to install was TOTALLY worth it. I’m loving it so far. I recommend watching the installation video and taking it slow~*
This is the first video I have seen that actually shows how to cut through the wall. All the other ones have the hole pre-cut and just show putting in the unit.
Great video. To the point. I've heard that you are supposed to slope the cabinet slightly downward on the outside so water/condensation drains away from the wall.
Hi hows your air-condition? It's been 4 years. I just ordered mine today but without the sleeve, do you think the sleeves are necessary? Does the unit supposed to breathe? The sleeves seems no ventilation. Thank you
I like these units and have had great luck with them. I built a 3 bedroom cabin and installed in each room and another in the living area and they work great. The biggest benefit I can see is that I can easily zone the cabin depending on how many people are there.
so lucky to have a wood exterior finish. Stucco is going to be a bit more challenging. Thanks for the upload. This is by far, much more detailed and direct to the point.
Yes, I could see stucco being more difficult, but really I did not have to replace or adjust from the outside of the house very much. (Just a bit of silicone sealant around the sleeve. So if you are careful with your cutting, hopefully the stucco will not chip or pull away, and you can do the same. Good luck!
Hi Dave, this is by far the best, and most complete video on this topic I've been able to find. I have a lot of experience doing plumbing and electrical work, as well as some framing and carpentry, but it really helped to see how you stepped through the process, built your header and footer, and well, just did it right! The instructions provided with my through the wall sleeve from Freidrich were all but useless and this video filled the gap completely. Thanks for taking the time to put it together!
Hey Chris, I appreciate you taking the time to let me know this video helped you out, it sounds like we were in the same place. The only reason I made the video was because I could not find anything showing the steps. Thanks!
So glad it could help. That’s the main reason I put it up was to give other people a leg up when doing their own projects. Hope your project all went well.
Nice voice over, I'll be doing this job soon myself, this was very helpful. Maybe I'll make a video too when I install mine....we'll see. Thanks for posting.
Thanks for an excellent video on this installation...have not found one this thorough and helpful...have a AC unit being delivered in a week and really needed to see how the sleeve was installed...thanks again!
nicely done. I am installing a Soleus AC and the sleeve instructions have to be the worst illustrations I've seen in any kit. One frame from your video solved the assembly riddle. Thanks!
Nice video but folks should know that the sleeve MUST have a 1/4” slope to ensure condensation doesn’t run back inside house or pool in unit & freeze in winter!
Great point! Yes, at the 2:50 mark, I mention to make sure the sleeve is level. (I of course mean left to right as the level is shown.) But I should also have stated that a slight tilt out is important.
Good job 👏 👍 I have to install a sleeve as well. I can't find any info about how far it is supposed to stick into the room. Very poor instructions on the sleeve and the actual unit.
Hey Dave, I pulled an AC unit out of my garage wall when I moved into my house because it didn't work and I boarded it up. now I'm getting ready to sell and I was thinking I would put a new AC unit in instead of trying to patch the stucco. Problem is that the hole in the wall measures just under 24 and a half inches and all the sleeves I find are 26 in. Any ideas?
That is a tough one. I think cutting it and adjusting the opening is your only option. I guess you also have to make sure the ac unit fits the sleeve. Good luck!
Dazzling Dave 1 - Question after you installed sleeve minimum 1 inch inside of house wall and finished. How many inches does your A.C. show inside of house the inches from the dry wall to the front of A.C. control panels. Thanks looks Great.
Hello, I am installing a though-wall AC this weekends. My sleeve didn't include holes to screw into the wall--noted to drill on sides only. What size and type of screws should I pick up at the hardware store? Thanks
Damn good job… !! Hard to find good videos for this types of AC. Any concerns about having to replace the unit and have to make all the adjustments to fit a new (different) unit ?
Thanks for watching my video and commenting. My unit is still running strong, so I have not had any issues whatsoever. My guess is when this one eventually does go out, I will be attempting to find a unit that will fit into the sleeve. (as opposed to putting a whole new sleeve in.
Hello Dave great Video, I have been going back with the Mini split or Wall unit , The pros & cons , I decided to go with a Through the wall unit with heat. The problem with the diy mini split was the the 410 Freon coil ,unless you have a long run to the inside unit ,you'll have all this coil left and u can't cut cause of the pre -charge .I saw a great install video where the coil was wrapped in a loop nice pro job but comments for the loop was a no no and would eventually shorten the life of the condenser., There were other electrical issues ,outside disconnect ect but really no biggies.. A standard unit without precharge was a option but after the install ,I would still have to have a Havc guy come out and charge the unit.and no pun intended for the $200 + cost,so as to being for my garage .I sized a nice through the wall unit. for my sq footage ....I would just want to note that I will be having a havc to replace my old top floor unit in the furture..
Hi Dave,... Did you have any problems with putting a WINDOW UNIT into a Wall? (i've heard that you need a wall unit for a wall). FOR ventilation and VENTS on the AC. ?
I think the unit I put in is a WALL unit...since the model number starts with (TTW) Which I think stands for Thru-The-Wall. But I had no problems at all or since.
@@dazzlingdaveyoyo Ok that's good. BUT that unit looks a little short to be a TTW unit. I would double check your VENTS to make sure its drawing air from outside. MYSELF, I will have to modify my SLEEVE system to get it work (my Unit is short and narrow, so the VENTS will not be outside without some modification)
Hi There! I am purchasing a tuff shed and will be ordering it with a hole pre-cut in it so that I can install a through the wall unit. Do I need to account for adding a header and a footer like you did? Or can I just have the cut out be exactly the size of the sleeve? Thanks!
I am not an expert on that kind of shed. But if you specify that you want to put in an ac unit when you are ordering the precut, I would expect they will be sure to have the proper strength built into it.
hi dave. is a sleeve necessary for wall ac units? i have an area on my wall to put my ac but not sure if i should pay extra for the ac sleeve. what would u recommend? :D
I would have used plywood, rather than OSB board, 3/8 plywood to be specific, in the header. I swear 1 1/2 + 1 1/2 +1/2 never equals 3 1/2. I have found though that 1 + 1/2 + 1 + 1/2 + 3/8 does equal three and a half. I was impressed with your video and your care about doing it correctly. And just for the fun of starting a silly argument once again. I'll say that your recip blade was in backwards
Thanks for your comment! I get what you mean about the thickness of different plywood and OSB boards. I just used what I had on hand that day. And it’s not upside down, it in just fine :-)
@@dazzlingdaveyoyo I'm not ranting against you, but I am ranting. I've always found that with the blade facing the other direction you're able to cut much flusher if you will. But I seem to lose this battle, everywhere I look people have the blade in the wrong way, I know I know, wrong to me but right to everyone else. Anyways the main point of my comment is that I thought you did a nice job of correctly making that opening.
Dude.... I was putting in in for this specific unit. I wanted the cord to point up so it would not stick down and take up space. So maybe upside down, but right for me.
In some places, upside down (as we are used to it) is now code... the thought being if a toddler or someone else pulls a cord out slightly and something conductive hits the exposed prongs, it will contact the ground prong first and then likely either the neutral or hot wire, hopefully causing a breaker to trip and no one getting electrocuted. I am in the process of doing some commercial work for DoD and the architecture and engineering firm we hired to do the building assessment told me about the recent code change. While it's not in place everywhere, expect to see more of this in the future!
@@ChrisWunsch Thx I have heard about this percieved safety set up. Didn't know it was going into the code. I really like the single prong down style, but oh well. :)
The framing was a little overkill for the load of one stud and the air conditioner weight but things should never move. Tapering the edges on the drywall makes it less likely to crack along the joints. Still a cooool video!
As you can see in this video, I did not need any special brackets for the sleeve. (Based on the instructions it was not needed.) Check with your sleeve's instructions to see if a mounting bracket is needed.
The sleeve did not fit exactly between the studs. (24” sleeve, 32” on center for the stud wall.) If you look at the beginning of the video it shows where I mark the studs and also where I cut out the wall. The studies are marked with a box and an “x”. When I added the header/footer it was the full width of that opening and I slipped it behind the slight amount of sheet rock to fit against the studs. The cripple studs on the side are against the other studs. I know more pictures or videos would have been beneficial….but hopefully this comment helps you.
Can I ask you- when you installed the wall sleeve, did you pitch it lower on the back end ( that sticks outside)? I’m asking because I purchased a wall sleeve and air conditioner- but it was missing the tapered foam blocks to give the AC a downward pitch when put into sleeve. I decided to pitch the sleeve when I secured it. I used a level to make certain. When I put the AC into the sleeve, I also pitched it ( used level on side that protrudes into my home). FWIW contacting the company to get those proper foam blocks has been unreal. Still deciding if I will remove and return it for a different brand, as I feel I should have been able to install correctly from the start. Great video, by the way.
José Fernandéz I did slightly tilt the sleeve away from the outside wall. That way the condensation from the AC unit will not leak into the wall, but instead gather in the pan and either drip out or evaporate from the pan outside the house.
Does the AC unit secure to the sleeve at all? Are there any screws or brackets or pressure fittings or anything or does it just shove in there and that's it? In my unit I have that same looking trim pieces but I don't see how anything attaches to the sleeve or to the wall. Just kind of sits there free floating I guess?
vigilantezack it has been a long time since I installed it....but if I recall it just slides into place and sits there. The units weight, and the pressure of the insulation also keeps it in place.
Does anyone know of this is a two-story house? Because why would he need such a large header for dispacing one stud? A single story home would just need a 2x4 frame around window. Or maybe it's code there.
The A/C unit should pull into the house as you remove it. I do not have a lot of experience with different models, but with mine, I would pop off the bezel on the inside, and remove any insulation/foam that is sealing around the edges. Then the unit should pull into the house. Again, I have only worked with my A/C unit, so I am not 100% sure yours would be the same. Good luck!
Tanner Schmitz. Yes, I am sure there are lots of different ways to go. But I already had this air-conditioner, so I had to do it that way! Thanks for checking out the video.
Tanner, I have two ductless mini-splits in my house and I love them. But if you're doing something for a single room, or in my case, a shop, and you don't want to spend $4K+ (in our area, the going rate) to have a ductless mini-split installed and electrical work done, this is a very affordable option. Both work fine, it really depends on your budget and use-case.
I have seen a few options that would help prevent someone from using that opening to gain entry to a house. Some manufacturers sell a cage that can be screwed to the outside of the house. Obviously you would want a screw head that is harder for the thief to have easy access to, so they cannot just unscrew the cage itself. I have also seen a small bracket that can be mounted on the inside of the house to help prevent the unit from being pushed easily into the home. Having said all that, if you have a very determined burglar, they are going to find a way in for sure.
Hi, I was looking at installing one of these in a conversion van. I desired this type so that It's back could be flush with the van and not be sticking out, which looks horrible. I presume these need to be level. How would I need to consider drain issues ?
Conlaoch Cattan, I really cannot speak toward van installation. But I know a slight angle out is required for drainage. There is a drain area on the lower right of the sleeve.(when looking at it from the outside.) I do not know how often it may need to drain, I have been running mine all summer, and it has not dripped.
mac daddy. I wonder if that is just a user preference? My wife wanted the minimum amount in the house. So that is how I set it up. There is an outdoor cover (insulated box) I use in the winter.
Danica 03. It depends on how much of the sleeve is into the room. I have seen some ac units about 10” into the room, mine is about 5”. (it will also depend on unit you are putting into the sleeve.)
@ Dazzling Dave: Thank you for making and sharing this video. But it would have been better if you showed us exactly what was being done, instead of showing pictures. Also, you were going a bit fast.
Yes, I totally agree. I didn’t think of making this video until I was just about done. I had been taking pictures along the way so I could show my family the process I was doing. In the end I decided to throw it up on my TH-cam channel because it might help people. If I was doing it over again I would shoot video.
It was a few years ago.....but if I recall correctly I found the A/C unit on Craigslist for $150 in amazing condition, and the sleeve at Menards was around $75 I think.
Howbout Nah. It has been a long time since I installed the unit. I remember researching it, and I believe with this unit it was not necessary....but again it was a while ago, so please don’t quote me on that.
Not 100% sure on all the terminology of this project. I meant the lower opening support for the bottom of the air conditioner. Sorry, I am not a professional....just getting the job done as well as I can. Thanks for checking out my video.
At about the 3:00 minute mark when the sleeve is being screwed into the opening, be sure there is a slope going out of the house. (I did about a 1/4 of an inch drop from front to back. This will make sure any drainage will drip outside of the house. Having said that, I have never had my AC unit drip into the sleeve. The water is kept in a tray in the AC unit itself, and evaporates out of the bottom of the unit.
None of the installers EVER talk about the "sleeve and the AC unit pitch/slope"....Extremely important or your AC will not work right in the long run!!!!
*It’s: Pretty. Quiet. **Fastly.Cool** in my room. Works wellLittle of hassle to install was TOTALLY worth it. I’m loving it so far. I recommend watching the installation video and taking it slow~*
This is the first video I have seen that actually shows how to cut through the wall. All the other ones have the hole pre-cut and just show putting in the unit.
Great video. To the point. I've heard that you are supposed to slope the cabinet slightly downward on the outside so water/condensation drains away from the wall.
Hi hows your air-condition? It's been 4 years. I just ordered mine today but without the sleeve, do you think the sleeves are necessary? Does the unit supposed to breathe? The sleeves seems no ventilation.
Thank you
Nice video Dave. Simple and straight to business. The best.
I like these units and have had great luck with them. I built a 3 bedroom cabin and installed in each room and another in the living area and they work great. The biggest benefit I can see is that I can easily zone the cabin depending on how many people are there.
so lucky to have a wood exterior finish. Stucco is going to be a bit more challenging. Thanks for the upload. This is by far, much more detailed and direct to the point.
Yes, I could see stucco being more difficult, but really I did not have to replace or adjust from the outside of the house very much. (Just a bit of silicone sealant around the sleeve. So if you are careful with your cutting, hopefully the stucco will not chip or pull away, and you can do the same. Good luck!
Hi Dave, this is by far the best, and most complete video on this topic I've been able to find. I have a lot of experience doing plumbing and electrical work, as well as some framing and carpentry, but it really helped to see how you stepped through the process, built your header and footer, and well, just did it right! The instructions provided with my through the wall sleeve from Freidrich were all but useless and this video filled the gap completely. Thanks for taking the time to put it together!
Hey Chris, I appreciate you taking the time to let me know this video helped you out, it sounds like we were in the same place. The only reason I made the video was because I could not find anything showing the steps. Thanks!
Thanks, no distracting music. Just to the point.
Thanks for sharing your experience, I'm in the middle of upgrading to an 8000 BTU unit and your video provided useful information.
So glad it could help. That’s the main reason I put it up was to give other people a leg up when doing their own projects. Hope your project all went well.
Nice job. Maybe just a block on both studs to attach a footer? Thank you for making the video I'm sure people learned a lot.
Excellent video. I love me some TH-cam!!
Thanks again boss!!! Have one of these jobs coming up👍👍
Nice voice over, I'll be doing this job soon myself, this was very helpful. Maybe I'll make a video too when I install mine....we'll see. Thanks for posting.
GREAT! EXACTLY what a video of this topic should be! Top notch.
Thanks, I appreciate your comment.
Thanks for an excellent video on this installation...have not found one this thorough and helpful...have a AC unit being delivered in a week and really needed to see how the sleeve was installed...thanks again!
Glad it could help. Good luck!
You are a beast man. Well done. Giving me the courage to make a whole ass hole in my wall.
nune44: take your time, have all the tools ready, and it will be a good project!
thank you for the video I really appreciate it and by the way you did a fantastic job installing your a/c unit
nicely done. I am installing a Soleus AC and the sleeve instructions have to be the worst illustrations I've seen in any kit. One frame from your video solved the assembly riddle. Thanks!
Charles I am glad it helped. I obviously found the instructions greatly lacking as well! Keep cool!
Where do I find the sleeve for my wall air conditioner
Nice video but folks should know that the sleeve MUST have a 1/4” slope to ensure condensation doesn’t run back inside house or pool in unit & freeze in winter!
Great point! Yes, at the 2:50 mark, I mention to make sure the sleeve is level. (I of course mean left to right as the level is shown.) But I should also have stated that a slight tilt out is important.
Thanks Kyron!!! That is the info piece I was seeking.
Thank you so much for your video. Great explanation on how to install the unit. 👏
So glad it helped you, check out my other videos if you want to learn about yo-yos, spintops, or other miscellaneous stuff! LOL
Good job 👏 👍 I have to install a sleeve as well. I can't find any info about how far it is supposed to stick into the room. Very poor instructions on the sleeve and the actual unit.
This is what I'm doing tomorrow. Thanks for the help.
I hope your project goes smoothly!
@@dazzlingdaveyoyo thank you
Hey Dave, I pulled an AC unit out of my garage wall when I moved into my house because it didn't work and I boarded it up. now I'm getting ready to sell and I was thinking I would put a new AC unit in instead of trying to patch the stucco. Problem is that the hole in the wall measures just under 24 and a half inches and all the sleeves I find are 26 in. Any ideas?
That is a tough one. I think cutting it and adjusting the opening is your only option. I guess you also have to make sure the ac unit fits the sleeve. Good luck!
Dazzling Dave 1 - Question after you installed sleeve minimum 1 inch inside of house wall and finished. How many inches does your A.C. show inside of house the inches from the dry wall to the front of A.C. control panels. Thanks looks Great.
Sergio Acosta. About 5 1/2 inches from drywall to front of A/C unit.
Hello, I am installing a though-wall AC this weekends. My sleeve didn't include holes to screw into the wall--noted to drill on sides only. What size and type of screws should I pick up at the hardware store? Thanks
Check with the guys at the hardware store. I would thin 1 1/2 inch Phillips head general purpose screw’s would work fine.
Excellent. Just want I needed thanks. Good job btw
Glad I could help!
Damn good job… !! Hard to find good videos for this types of AC.
Any concerns about having to replace the unit and have to make all the adjustments to fit a new (different) unit ?
Thanks for watching my video and commenting.
My unit is still running strong, so I have not had any issues whatsoever.
My guess is when this one eventually does go out, I will be attempting to find a unit that will fit into the sleeve. (as opposed to putting a whole new sleeve in.
Hello Dave great Video, I have been going back with the Mini split or Wall unit , The pros & cons , I decided to go with a Through the wall unit with heat. The problem with the diy mini split was the the 410 Freon coil ,unless you have a long run to the inside unit ,you'll have all this coil left and u can't cut cause of the pre -charge .I saw a great install video where the coil was wrapped in a loop nice pro job but comments for the loop was a no no and would eventually shorten the life of the condenser., There were other electrical issues ,outside disconnect ect but really no biggies.. A standard unit without precharge was a option but after the install ,I would still have to have a Havc guy come out and charge the unit.and no pun intended for the $200 + cost,so as to being for my garage .I sized a nice through the wall unit. for my sq footage ....I would just want to note that I will be having a havc to replace my old top floor unit in the furture..
Hi Dave,...
Did you have any problems with putting a WINDOW UNIT into a Wall?
(i've heard that you need a wall unit for a wall). FOR ventilation and VENTS on the AC.
?
I think the unit I put in is a WALL unit...since the model number starts with (TTW) Which I think stands for Thru-The-Wall. But I had no problems at all or since.
@@dazzlingdaveyoyo Ok that's good. BUT that unit looks a little short to be a TTW unit. I would double check your VENTS to make sure its drawing air from outside. MYSELF, I will have to modify my SLEEVE system to get it work (my Unit is short and narrow, so the VENTS will not be outside without some modification)
Mine fit the sleeve correctly. The back of the unit fit snugly against the frame.
@@dazzlingdaveyoyo Where did you BUY that Unit...i can't seem to locate a Wall-Unit AC....thanks!
Yes, there is a specific vent for the back of the unit to make sure it is pulling air from the correct area.
Hi There! I am purchasing a tuff shed and will be ordering it with a hole pre-cut in it so that I can install a through the wall unit. Do I need to account for adding a header and a footer like you did? Or can I just have the cut out be exactly the size of the sleeve? Thanks!
I am not an expert on that kind of shed. But if you specify that you want to put in an ac unit when you are ordering the precut, I would expect they will be sure to have the proper strength built into it.
Great video and if you didn't have your name on it I would have thought I was watching a Mike Rowe video...lol
Thanks! Glad you liked it! Now only if I could make as much $ for speaking as Mike, that would be something.
hi dave. is a sleeve necessary for wall ac units? i have an area on my wall to put my ac but not sure if i should pay extra for the ac sleeve. what would u recommend? :D
Yes, you will definitely want a sleeve. It holds the unit properly and gives an avenue for drainage.
I would have used plywood, rather than OSB board, 3/8 plywood to be specific, in the header. I swear 1 1/2 +
1 1/2 +1/2 never equals 3 1/2. I have found though that 1 + 1/2 + 1 + 1/2 + 3/8 does equal three and a half. I was impressed with your video and your care about doing it correctly.
And just for the fun of starting a silly argument once again. I'll say that your recip blade was in backwards
Thanks for your comment! I get what you mean about the thickness of different plywood and OSB boards. I just used what I had on hand that day.
And it’s not upside down, it in just fine :-)
@@dazzlingdaveyoyo I'm not ranting against you, but I am ranting. I've always found that with the blade facing the other direction you're able to cut much flusher if you will. But I seem to lose this battle, everywhere I look people have the blade in the wrong way, I know I know, wrong to me but right to everyone else. Anyways the main point of my comment is that I thought you did a nice job of correctly making that opening.
"get an electrician to help you if you don't know electrical" proceeds to put the outlet upside down
Dude.... I was putting in in for this specific unit. I wanted the cord to point up so it would not stick down and take up space. So maybe upside down, but right for me.
@@dazzlingdaveyoyo Dude. Relax. It was just funny and ironic
I am relaxed. Just thought you were being serious!😜
In some places, upside down (as we are used to it) is now code... the thought being if a toddler or someone else pulls a cord out slightly and something conductive hits the exposed prongs, it will contact the ground prong first and then likely either the neutral or hot wire, hopefully causing a breaker to trip and no one getting electrocuted. I am in the process of doing some commercial work for DoD and the architecture and engineering firm we hired to do the building assessment told me about the recent code change. While it's not in place everywhere, expect to see more of this in the future!
@@ChrisWunsch Thx I have heard about this percieved safety set up. Didn't know it was going into the code. I really like the single prong down style, but oh well. :)
The framing was a little overkill for the load of one stud and the air conditioner weight but things should never move. Tapering the edges on the drywall makes it less likely to crack along the joints. Still a cooool video!
Thanks for checking out my video, and commenting. I appreciate the feedback.
Are supporting brackets necessary for through the wall ac units?
As you can see in this video, I did not need any special brackets for the sleeve. (Based on the instructions it was not needed.)
Check with your sleeve's instructions to see if a mounting bracket is needed.
Did you shorten the cord? Looks so clean like that!! Awesome.
I did not cut the cord to shorten it.
But it is bundled up tight on the side of the unit.
Nice...good video..Thanks
BTW, what size Unit is that....looks like a 6000 BTU ???
Thanks! It is a 10,000 BTU model. Cools the room down nicely.
So did the sleeve fit exactly between 2 studs? It was unclear to what the right side of the header was attached.
The sleeve did not fit exactly between the studs. (24” sleeve, 32” on center for the stud wall.)
If you look at the beginning of the video it shows where I mark the studs and also where I cut out the wall. The studies are marked with a box and an “x”.
When I added the header/footer it was the full width of that opening and I slipped it behind the slight amount of sheet rock to fit against the studs. The cripple studs on the side are against the other studs.
I know more pictures or videos would have been beneficial….but hopefully this comment helps you.
Can I ask you- when you installed the wall sleeve, did you pitch it lower on the back end ( that sticks outside)? I’m asking because I purchased a wall sleeve and air conditioner- but it was missing the tapered foam blocks to give the AC a downward pitch when put into sleeve.
I decided to pitch the sleeve when I secured it. I used a level to make certain.
When I put the AC into the sleeve, I also pitched it ( used level on side that protrudes into my home).
FWIW contacting the company to get those proper foam blocks has been unreal. Still deciding if I will remove and return it for a different brand, as I feel I should have been able to install correctly from the start.
Great video, by the way.
José Fernandéz I did slightly tilt the sleeve away from the outside wall. That way the condensation from the AC unit will not leak into the wall, but instead gather in the pan and either drip out or evaporate from the pan outside the house.
Does the AC unit secure to the sleeve at all? Are there any screws or brackets or pressure fittings or anything or does it just shove in there and that's it?
In my unit I have that same looking trim pieces but I don't see how anything attaches to the sleeve or to the wall. Just kind of sits there free floating I guess?
vigilantezack it has been a long time since I installed it....but if I recall it just slides into place and sits there. The units weight, and the pressure of the insulation also keeps it in place.
Does anyone know of this is a two-story house? Because why would he need such a large header for dispacing one stud? A single story home would just need a 2x4 frame around window.
Or maybe it's code there.
Hey Dave I have one in the wall and it needs cleaned I can’t figure out how to remove the A/C from the sleeve please help me
The A/C unit should pull into the house as you remove it. I do not have a lot of experience with different models, but with mine, I would pop off the bezel on the inside, and remove any insulation/foam that is sealing around the edges. Then the unit should pull into the house.
Again, I have only worked with my A/C unit, so I am not 100% sure yours would be the same. Good luck!
I’m installing a unit in my house and it has a grounding wire. I didn’t see yours had a grounding wire installed at any point. Any advice?
My advice would be to attach the wire to the sleeve. And make sure you use a properly grounded three prong outlet.
Nice video! But for all that trouble you went through I’d probably just go with a mini split unit to avoid tearing up all my walls personally
Tanner Schmitz. Yes, I am sure there are lots of different ways to go. But I already had this air-conditioner, so I had to do it that way! Thanks for checking out the video.
@tanner what do you mean by mini split unit?
Tanner, I have two ductless mini-splits in my house and I love them. But if you're doing something for a single room, or in my case, a shop, and you don't want to spend $4K+ (in our area, the going rate) to have a ductless mini-split installed and electrical work done, this is a very affordable option. Both work fine, it really depends on your budget and use-case.
Very helpful...
Although my wall is made of 6 inches how blocks with thick plaster, rebars and grout in cores... It's another story.
Yeah…. That would make this project a lot harder!
Home pipe bombs- hole is No Problem. LOL
Is there a way to prevent a would-be thief from pushing the unit into the house and gaining entry?
I have seen a few options that would help prevent someone from using that opening to gain entry to a house. Some manufacturers sell a cage that can be screwed to the outside of the house. Obviously you would want a screw head that is harder for the thief to have easy access to, so they cannot just unscrew the cage itself.
I have also seen a small bracket that can be mounted on the inside of the house to help prevent the unit from being pushed easily into the home.
Having said all that, if you have a very determined burglar, they are going to find a way in for sure.
Great video, what did you use to cut threw the wall?
Khal Mykey I used a reciprocating saw.
Did you watch the video?
Hi, I was looking at installing one of these in a conversion van. I desired this type so that It's back could be flush with the van and not be sticking out, which looks horrible. I presume these need to be level. How would I need to consider drain issues ?
Conlaoch Cattan, I really cannot speak toward van installation. But I know a slight angle out is required for drainage. There is a drain area on the lower right of the sleeve.(when looking at it from the outside.)
I do not know how often it may need to drain, I have been running mine all summer, and it has not dripped.
Thanks. Maybe I'll make a video about it. Your right about not that much online. The unit I'm getting is ac and heat.
A wall a/c is supposed to go in deeper so that you can put an indoor cover on it during the winter months? The final result looks strange.
mac daddy. I wonder if that is just a user preference? My wife wanted the minimum amount in the house. So that is how I set it up. There is an outdoor cover (insulated box) I use in the winter.
Do you find it sticks out like 4 inches from the wall??
Danica 03. It depends on how much of the sleeve is into the room. I have seen some ac units about 10” into the room, mine is about 5”. (it will also depend on unit you are putting into the sleeve.)
Great video! Thanks
@ Dazzling Dave: Thank you for making and sharing this video.
But it would have been better if you showed us exactly what was being done, instead of showing pictures.
Also, you were going a bit fast.
Yes, I totally agree. I didn’t think of making this video until I was just about done. I had been taking pictures along the way so I could show my family the process I was doing. In the end I decided to throw it up on my TH-cam channel because it might help people. If I was doing it over again I would shoot video.
@@dazzlingdaveyoyo Ok thanks.
Thanks, that was awesome!
Glad you liked it! Thanks for checking out my channel.
How much does it cost? I'm just wondering
It was a few years ago.....but if I recall correctly I found the A/C unit on Craigslist for $150 in amazing condition, and the sleeve at Menards was around $75 I think.
Did you put in support brackets??
No support brackets were needed for my sleeve and ac unit.
is it not necessary to install a ground wire from the unit to the sleeve?
Howbout Nah. It has been a long time since I installed the unit. I remember researching it, and I believe with this unit it was not necessary....but again it was a while ago, so please don’t quote me on that.
@@dazzlingdaveyoyo i appreciate the reply, the installation instructions say its optional but i think im going to do it anyway just to be safe
Well done.
What is a "Footer" Do you mean the Sill ? Jack studs or trimmers under the header, Cripples studs under the sill.
Not 100% sure on all the terminology of this project. I meant the lower opening support for the bottom of the air conditioner. Sorry, I am not a professional....just getting the job done as well as I can. Thanks for checking out my video.
at what point do i slope the ac for drainage?
At about the 3:00 minute mark when the sleeve is being screwed into the opening, be sure there is a slope going out of the house. (I did about a 1/4 of an inch drop from front to back. This will make sure any drainage will drip outside of the house.
Having said that, I have never had my AC unit drip into the sleeve. The water is kept in a tray in the AC unit itself, and evaporates out of the bottom of the unit.
Nice Video Production...
May i ask **'What video editing program did you use ?'**
Thanks, I shot and edited it all on my iPhone. I used iMovie to put it all together.
Great great video bub
Where do u order the sleeve?
I found mine at Menards, in stock and on the shelf last year.
None of the installers EVER talk about the "sleeve and the AC unit pitch/slope"....Extremely important or your AC will not work right in the long run!!!!
Every unit is different...take a look at yours.
a little bit cooler???HOW ABOUT TONS OF TIMES COOLER BUUURRRRRR!!!