would be more easily seen from the front of the gun but great improvements to the video quality. Definitely have to have an understanding of what you are working on to do this. Not just anyone can jump into this and make it work but it WORKS 💯👌
Mate I total agree, ive said it from the beginning. We are working on videos installing in different AK's and how to make them fit, but this takes time, but they are coming
@@alfatacticalsystems1582thank you for taking the time to reply to the community comments. Definitely support your project and the hard work you’re doing behind the scenes.
Will you develop the 3 position kit for your trigger or make the 3 position version of your trigger (note: the FRT mode is at the middle, like the original full-auto AK)?
@@jonjones3415 It slips over the paddle and push it down on the paddle as far as it will go. It keeps the paddle centered in the bolt carrier. Can run with or without, better to run with it because it won't bind on you.
check out #workingclassless, or SooLicytyson, they both have Dracos. It sounds like you havent got the retainer plate lined up correctly, please email me a picture to info@marstrigger and I will take a look
@ sooicytyson is my homie he’s tried to help too. I mean I’m sure it is something I’m doing wrong but in the tutorial it’s just a lil hard to tell what he’s doing because the video cuts off and just shows him clamping it in
My safety has issues also if I put it in safe the little bar inside falls out of the groove but I think mine has other issues cause I had to trim my bar to fit in my ak, the ak I’m using isn’t a typical century or Zastava so that could be the issue also
I ordered two with the intention of installing it on my AES-10B. The silver rods I received in both kits are different lengths and bent in different directions. The piece that mounts to the AK's safety doesn't stop the trigger from being pulled enough to stop the hammer from falling and the hammer ends up just following the bolt forward. Have tried it with the G2 trigger and the ALG. The ALG wouldn't allow the piece that mounts to the safety to even REACH the trigger. Can't figure it out for the life of me. Have tried installing it on my O-Pap and Mini Draco with no luck as well.
This video doesnt show how or where the front hook of the rod connects or interacts with the carrier. Did i miss something? Also, the Aussie might just be the coolest part of all of this!!!
Show me how you make the Ruger Chassis. I got an acquaintance trying to sell me two tormach(not sure I'm spelling it right, same brand of machine you got) cnc mills for $20,000(for both). One is I wanna say an 1100 series and one is like a 770 if I remember correctly. Both have been used quite a bit. My mentors at work(I'm still an apprentice in a tool and die shop, I started as a tool and die apprentice but swapped to full time CNC) told me if I'm gonna get a machine to just lease a small haas. Another machinist friend of mine has said the same thing, haas mini mill or a step up from that.
Really can’t wait for the selectable one to come
cant really see whats going on, plz try again, with MOAR lighting & be aware of hands in the way. so hyped tho ❤🔥☦🦅💪
No tooling needed it is revolutionary
would be more easily seen from the front of the gun but great improvements to the video quality. Definitely have to have an understanding of what you are working on to do this. Not just anyone can jump into this and make it work but it WORKS 💯👌
Mate I total agree, ive said it from the beginning. We are working on videos installing in different AK's and how to make them fit, but this takes time, but they are coming
@@alfatacticalsystems1582thank you for taking the time to reply to the community comments. Definitely support your project and the hard work you’re doing behind the scenes.
Will you develop the 3 position kit for your trigger or make the 3 position version of your trigger (note: the FRT mode is at the middle, like the original full-auto AK)?
They said they are. That’s what I want
@ぷらぐ they did? Can you send me the video where they said that?
just ordered mine a few daays ago i cannot wait!
thanks mate. It will be out monday
Where to order? Will it work on Romanian rpk?
PEEEEEEEETE! WUSSUPP!? Hope ya'll are doing good my brother from across the pond..we love you bud
@IndependentArmz hey mate, how are you guys? Happy new year
My reset bar is just a tad bit too short and keeps falling out of the piece it’s supposed to go in. Do you sell replacement pieces?
Same with mine you have to bend it
is this just safe and super safe or is there still a semi setting
What the brand of that ak ?
Great video! Thanks... Now we need on on Mars Super Safety, only question i have on those is what to do with the plastic spacer,if needed
It's for the paddle to stay centered.
Or are your referring to the MARS device?
@@yourangerfuelsme perfect Thanks!
@@yourangerfuelsme so it goes into the paddle track? Thanks
its if you have any side ways movement, its to stop it, if you dont have any you dont need it
@@jonjones3415 It slips over the paddle and push it down on the paddle as far as it will go. It keeps the paddle centered in the bolt carrier. Can run with or without, better to run with it because it won't bind on you.
When I put my safety back it won’t clamp. Almost like the safety pin isn’t long enough anymore with all this stuff in there. I have a full sized Draco
check out #workingclassless, or SooLicytyson, they both have Dracos. It sounds like you havent got the retainer plate lined up correctly, please email me a picture to info@marstrigger and I will take a look
@ sooicytyson is my homie he’s tried to help too. I mean I’m sure it is something I’m doing wrong but in the tutorial it’s just a lil hard to tell what he’s doing because the video cuts off and just shows him clamping it in
@ I emailed
My safety has issues also if I put it in safe the little bar inside falls out of the groove but I think mine has other issues cause I had to trim my bar to fit in my ak, the ak I’m using isn’t a typical century or Zastava so that could be the issue also
I ordered two with the intention of installing it on my AES-10B. The silver rods I received in both kits are different lengths and bent in different directions. The piece that mounts to the AK's safety doesn't stop the trigger from being pulled enough to stop the hammer from falling and the hammer ends up just following the bolt forward. Have tried it with the G2 trigger and the ALG. The ALG wouldn't allow the piece that mounts to the safety to even REACH the trigger. Can't figure it out for the life of me. Have tried installing it on my O-Pap and Mini Draco with no luck as well.
Yeah, cuz it's s a bootleg knockoff
@ Of what? Is anyone else selling them?
@muldrowe yeah Alfa tactical stole the design, he does not even sell a complete kit.....and you obviously see the lack of quality control in the parts
@@killerfungis So can I get a better kit from somebody else or no?
@muldrowe yes, I will message you Monday, don't have the name with me, on the road
Cool beans
This video doesnt show how or where the front hook of the rod connects or interacts with the carrier.
Did i miss something?
Also, the Aussie might just be the coolest part of all of this!!!
Show me how you make the Ruger Chassis. I got an acquaintance trying to sell me two tormach(not sure I'm spelling it right, same brand of machine you got) cnc mills for $20,000(for both). One is I wanna say an 1100 series and one is like a 770 if I remember correctly. Both have been used quite a bit. My mentors at work(I'm still an apprentice in a tool and die shop, I started as a tool and die apprentice but swapped to full time CNC) told me if I'm gonna get a machine to just lease a small haas. Another machinist friend of mine has said the same thing, haas mini mill or a step up from that.
Can i put this in any ak?
most, if its a draco or an underfolder, modification will be needed to make it work, just because the trunnion is different.
@alfatacticalsystems1582 so it will work with like a regular Century VSKA or BFT47? Those have regular trunions . The BFT is a bulged one.
Crikey put another shrimp my barbie and another Ak in me Armory
Hard to see need more lighting! But thank you great video!👍🏽😊❤️🇺🇸
Cheers Mate, our old video was bad, I my wife tells me I have no filter and Tourettes
Could this be remade with more light please@@alfatacticalsystems1582
Cant see anything
Really hard to see!!
believe me mate, our last video was shit in comparison, but I will pass on your feedback and let them know
Until there is a 3 Position version of this, this is really not that useful of a product.
Can't hardly hear you, move out of your parents' garage.