Thank you very much for sharing. But when I was co-simulating, the simplorer's progress bar looked like it was stuck and there was no progress. There is no error in the message box. Have you ever encountered this?
thank you dear mr kamyar i have a problem with my cosimulation. there is an error in my simulation as below: [Sim2000] Error - FEA1: ERROR - could not find a transient operating point before launching Maxwell could you please comment?
Hello Mr. Kamyar K....I am trying to do co simulation and set up everything according to the video. How can I add output from maxwell is force of magnetic.
Hello sir, What about the time steps in Maxwell? do we need to specify the end time and increment time the same as the twin builder/Simplorer or different values will also work?
Dear Sir, when I did the co-simulation between Simplorer and Maxwell, it took 1 hour to finish the simulation. I think the reason might be my coils model (the number of turns is 80). Can you let me know whether the number of turn affects to the simulation time or not? If yes, how can we reduce the simulation time? Thanks.
Hi，I am a master student using ANSYS maxwell a lot during my work. Based on my experience it is normal to take several hours to finish a simulation. The time is highly depended on how much precise of your simulation so if you want to increase the speed you can use larger mesh grid in your simulation. As well the accuracy would be reduced. Thus a trade-off should be made between the accuracy and the speed. I usually use maxwell to evaluate my design for planar transformers thus I selected the mesh grid based on frequency, considering skin and proximity effect. Hope my comment is useful for you and we can have further communication if you want.
Hello Mr. Kamyar K....I am trying to do co simulation and set up everything according to the video. Problem is when I am importing the blackbox from maxwell to simplorer, no port is showing there where I can connect to the circuit I have made in simplorer. Please let me know what mistake I am doing
I had the same problem. To solve it go to your Maxwell project and inside the "Excitation" tab right click over one of your defined windings (in this videos the windings are called Rx and Tx) and select the option "Properties". A new window will be displayed and Inside the "Parameters" you have one option called "Type". Select the option "External" inside this box. Repeat the same process for all your defined windings. Then repeat as shown in the video to import it to simplorer. I Hope this helps.
HI Kamyer, Thank you very much for your video, but I have finished analyzing the simplorer, but the result is always not running, has anyone encountered this problem, is it because I am not using Twin Builder? The frequency I use is 100KHZ
Hi. In case of maxwell 2D/3D cosimulation with simplorer in case of BLDC/PMSM motor when i import the subcircuit I am getting six terminals for motor windings which is fine but I did not get terminals for load torque and speed. Is it required to assign band in maxwell for motor application with simplorer transient co simulation? Also how to derive Hall effect signals in simplorer from maxwell 2D/3D?
Hi, i have a problem in translating the current density profile (with parasitics from Q3D) from simplorer to maxwell. i am trying to plot the current density onto the pcb traces to look for hotspots. can you guide me in this regard?
Hello Mr. Kamyar K.....Is there any way I can see field(E or H) around the geometry which I used using this simulation data? What I found is in simplorer I can find only circuit parameter. How to visualise field?
Sir, I am trying to do simulation of a pancake coil and a steel disk in eddy current solution type. when i was trying to give excitation at the coil terminal, this error is coming " excitation may not be assigned on non modal objects. what does this mean? what mistake i have done? please let me know. thank you sir
Dear Kamyar, I designed a single-phase transformer in maxwell2d and imported it into simplorer. Source voltage (connected to primary) in simplorer has a pi/2 (90 degree) phase, so i expected that inrush current would not occur. But it occurs whatever i do. However, in maxwell2d, inrush current does not occur if the phase is pi/2. I cannot figure out what to do, do you have any idea? What should I do to avoid inrush current in simplorer? Thank you so much for your tutorial video, it is helpfull.
When i click add transient cosimulation, the coil is append but it do not have the pins to connect with simporer circuit, i am working in version 19, thanks!
Mr. Kamywar when I tried to ask the maxwell co-simulation circuit, I only get one terminal. I don't get 4 terminals like you do, can you please help me on what I could have done wrong here? Thank you
+MoeAzizBadawi Hi, make sure that you define windings for all excitations and make sure that you set the windings to external current. in te simpler try to delete the sub circuit and replace it by new one. hope it helps.
+kamyar K it worked thanks a lot. I just have 2 small question if possible, I have designed a Class E inverter and I like to use it as my power source. The output of the inverter is High freq1 MHz current, I connected to the along the circuit instead of the Voltage source, but I'm not getting any proper outputs for the power efficiency. Is there a reason behind that? One more thing how could generate A PWM output to driver a power MOSFET any idea? I just copied one the block designed for an example. Thanks a lot, I know this is a lot. I apologize for that, but I really need to get a decent output to use for my project.
MoeAzizBadawi hi, Make sure that the inverter can support tgr current that is required by your sub circuit terminals. If you are making a resonator and its a series resonator at the frequency of resonance you have short circuit. That can cause problem. There is pulse source that you can easily use it as pwm. If I understood your question rightly. Do you mean how you can do it in simulator not real life right? In real life you can use a bjt to drive the pwm pulse coming out of the micro. Or simply by a driver and use that to buffer the gate of power MOSFET.
Dear sir, Thank you so much for your very helpful videos. I am working on Wireless Power Transfer. I have faced some problems while I was working on the Simplorer -Maxwell co-simulation. Will you please clear me the idea about the Winding properties and the External Source for excitation. When I put my Maxwell design into the simplorer, no pins were shown to connect.And one more query where can I get the next episode of this video I mean the result part
Hi Kamyar, Thanks a lot for the great tutorial! Very helpful indeed. I have the same design in Maxwell and also the same circuit in Simplorer. However, when I try to import the Maxwell design into Simplorer, it doesn't have ports for connection. I have tried changing various settings and configurations but nothing is helping. When I import from Maxwell, I get a box in Simplorer with no ports for connection so cant proceed from there. Any help form your would be highly appreciated!
I looked at all of your previous comments and found the answer in one of them. The terminals appeared when I set the winding as external instead of current (right click on winding, go to properties and select external in the type). Thanks a lot!
Hello Kamyar K, I was using ANSYS 18.0.0 version All simulations at MAXWELL tool goes perfect, when I am going to simplorer i design the circuit bs when clicking on simplorer circut --> subcircuit--> MAXWELL components there is no Add dynamic inductance we have Add dynamic magnetostatic Can you help me ???
+kamyar K dear for dynamic analysis i have seen 3 parts... is there any other part for transient analysis...? if yea plz share its reference... thanx in advance
Dear i want to ask about transient analysis for WPT.... May u feel my question silly but i am confused that what kind of results we can obtain from transient analysis of WPT..like L, flux linkage, losses etc. 2-Another thing i want to ask is that how can we find inductance of coil on certain frequency like for 100khz..?
Dear Kamyar I have designed PM motor in maxwell and inverter in Simplorer. I am using cosimulation and everything works fine. But I have seen many places that people attach a resistance and an inductance in series with each phase of the machine. Why is this resistance and inductance needed? Is this the resistance and inductance of machine windings itself or what else? Because I am not using any resistance and inductance in my circuit and this may affect the system analysis
Hi , In the upcoming tutorial that I am uploading I will go over this in detail. But generally those are the parasitic inductors that you may have and the winding resistance. In the maxwell the winding resistance is not being calculated unless you provide it. does it answer your question?
Dear Sir, your video on Maxwell are awesome! I am having some troubles about the cosimulation of a switched reluctance machine Maxwell file and the corresponding drive in simplorer. The maxwell simulation is transient since I need to rotate the machine. I have got the following three error. Could you please help me? Thank you! Error - FEA1: ERROR - could not find a transient operating point before launching Maxwell >> Calculate Error 11557 - Error encountered in the Simulate function of user model. Model: FEA1.MAXWELL >> Calculate Error 13431 - Fatal error encountered while updating models. Model: FEA1.MAXWELL >> Calculate Error 10564 - Simulation aborted. >> Calculate
Hi, I have some more Errors: Error - FEA1: an existent connection was closed by the remotehost. >> Calculate (translated from german) Error 11557 - Error encountered in the Simulate function of user model. Model: FEA1.MAXWELL >> Calculate Error 13431 - Fata error encountered while updating models. Model FEA1.MAXWELL >> Calculate Error - Error while updating model values and states. >> Calculate I have build a simple circuit with two parallel coils and a data signal for the voltage. At first glance, it looked like, that maybe the connection to the licence server or some kind of overload could be the reason. I could not find any numerical problems, but I repeated it with different setting for minimal and maximal time step and it resulted in the same abortion around the same simulation time. The data signal is constant between 3.5 ms and 10 ms, the error occurs around (8.5+/-0.3) ms, so I think it should be a numerical issue. Any idea, what could be the reason for this error or some tipps, where to check?
Hi Mr. Kamayar, When I run analysis in simplorer with maxwell 3D, such kind of error occurs. The source design for Simplorer is required to have transient-transient link enabled. Simulation completed with execution error on server. An external simulator couldn't be setup for simulation. If you don't mind, could you please have a look to these error. I cannot find how to solve it. Thanks you.
Watch the co-simulation tutorial and you would see you need to check a check box in maxwell design setting before you Be able to run the cosimulation. Check the very early videos of mine about co-simulation.
hi I am having this error, "Simplorer requires the source solution 'Setup1 : LastAdaptive' to have a frequency sweep of at least '20' points". The frequency I am using is 2.5 kHZ.
Dear Sir. Thank you for you video. I meet a problem about the co-simulation. When I add Maxwell component, the message in simplorer have an error: Unable to find model 'MxTranTranData', please check your configured libraries. and the model in schematic has no pin to connect with circuit's other part. Please help me with some advise. Thank you very much.
王宇辰 Hi, make sure you are making windings and assigning the excitations to the windings and MAKE SURE IN WINDINGS PROPERTY YOU ARE SELECTING EXTERNAL SOURCE FOR THE EXCITATION. if you dont set the external it would not give pins. let me know if it hasn't fixed yet.
Hi Kamyar, I am trying to find that video where you explain external circuit excitation in Maxwell, but I can't seem to find a video title that fits this. Could you tell me which video it is?
Dear Sir, I am getting the following errors while doing a transient transient cosimulation. What may be the reason for these ? Error 13431 - Fatal error encountered while updating models. Model: FEA1.MAXWELL >> Initialize [error] [Sim2000] Error - Error while updating model values and states. >> Initialize [error] [Sim2000] Error 10523 - Error encountered while initializing the simulators. >> Initialize [error] [Sim2000App] Error 10533 - Error encountered during INIT. >> Initialize
+Srijan Datta this happens when you have nested capacitors without initial values. Remove unnecessary caps and put a cap very small with initial voltage on floating nodes. That should help you to do the sim.
HELP! When I try to import my 3D design to Simplorer, its dont find the model.. The error is: "You must select a design" I did step by step, but it doesn't work. Anyone can help me? Thanks.
+Renata Rezende Reis in simplorer you don't import a step file. In maxwell you import the step file and in the simplorer you import the maxwell setup file. Please watch again
Mr Kamyar, When I'm trying to add the maxwell sub circuit to the simplorer circuit it doesn't generate details and cannot add the sub circuit saying that "You must select a design". Can you please point out me the thing that I'm doing wrong?...
![210- Ansys Maxwell - Simulating Reluctance Motor [part1]](http://i.ytimg.com/vi/tvD1pc494sc/mqdefault.jpg)
![210- Ansys Maxwell - Simulating Reluctance Motor [part1]](/img/tr.png)
Thank you! 10 years later and this is still valuable.
Your videos were really helpfull. Thank you a lot!
Thank you so much for your videos.
SO Valuable
Thankyou very much!! Now able to link max to sim.
Hey mr. kamyar, I am unable to create four terminals of maxwell 3d WPT block when exporting to simplorer. Please help
Hey man, great work....Any idea how to link Simulink and Maxwell 3D Electrostatics directly for material parameterisation?
Thank you very much for sharing. But when I was co-simulating, the simplorer's progress bar looked like it was stuck and there was no progress. There is no error in the message box. Have you ever encountered this?
hi , kamyar, if you want to optimize structure according to the result of simplorer, what should you do?
You can use parameters in Maxwell and according to results of simplorer update the parameters and re-run in simplorer.
thank you dear mr kamyar
i have a problem with my cosimulation. there is an error in my simulation as below:
[Sim2000] Error - FEA1: ERROR - could not find a transient operating point before launching Maxwell
could you please comment?
Hi, Did you solve this error?
Thank you
Hello Mr. Kamyar K....I am trying to do co simulation and set up everything according to the video. How can I add output from maxwell is force of magnetic.
Hi sir, only transient model can be used for co-simulation?
no
Hello sir,
What about the time steps in Maxwell? do we need to specify the end time and increment time the same as the twin builder/Simplorer or different values will also work?
No, it will be dictated by Simplorer
Dear Sir, when I did the co-simulation between Simplorer and Maxwell, it took 1 hour to finish the simulation.
I think the reason might be my coils model (the number of turns is 80).
Can you let me know whether the number of turn affects to the simulation time or not? If yes, how can we reduce the simulation time?
Thanks.
Hi，I am a master student using ANSYS maxwell a lot during my work. Based on my experience it is normal to take several hours to finish a simulation. The time is highly depended on how much precise of your simulation so if you want to increase the speed you can use larger mesh grid in your simulation. As well the accuracy would be reduced. Thus a trade-off should be made between the accuracy and the speed. I usually use maxwell to evaluate my design for planar transformers thus I selected the mesh grid based on frequency, considering skin and proximity effect. Hope my comment is useful for you and we can have further communication if you want.
Hi Mr. Kamayar,
May I know what settings do you set for add winding under excitation?
Thanks.
Under excitation (in transient solution only ) you can find add winding option.
Hello Mr. Kamyar K....I am trying to do co simulation and set up everything according to the video. Problem is when I am importing the blackbox from maxwell to simplorer, no port is showing there where I can connect to the circuit I have made in simplorer. Please let me know what mistake I am doing
I had the same problem. To solve it go to your Maxwell project and inside the "Excitation" tab right click over one of your defined windings (in this videos the windings are called Rx and Tx) and select the option "Properties". A new window will be displayed and Inside the "Parameters" you have one option called "Type". Select the option "External" inside this box. Repeat the same process for all your defined windings. Then repeat as shown in the video to import it to simplorer. I Hope this helps.
nice useful video. Also, can we get field plots of maxwell model in simplorer?
just in Maxwell you can see the field plots
HI Kamyer, Thank you very much for your video, but I have finished analyzing the simplorer, but the result is always not running, has anyone encountered this problem, is it because I am not using Twin Builder? The frequency I use is 100KHZ
there can be many reasons, share the screenshot of the error please
Hi. In case of maxwell 2D/3D cosimulation with simplorer in case of BLDC/PMSM motor when i import the subcircuit I am getting six terminals for motor windings which is fine but I did not get terminals for load torque and speed.
Is it required to assign band in maxwell for motor application with simplorer transient co simulation?
Also how to derive Hall effect signals in simplorer from maxwell 2D/3D?
Hi,
i have a problem in translating the current density profile (with parasitics from Q3D) from simplorer to maxwell. i am trying to plot the current density onto the pcb traces to look for hotspots. can you guide me in this regard?
+Shahid it is quite design specific. What's the error. ?
Hello Mr. Kamyar K.....Is there any way I can see field(E or H) around the geometry which I used using this simulation data? What I found is in simplorer I can find only circuit parameter. How to visualise field?
Simplorer is system-level simulator. you need to get back to Maxwell environment to visualize the fields
Can i use the simplorer to extract the equivalent circuit of my antenna which i designed using HFSS or CST?
I think you can by calculating the impedance and work it out. but better than that use Q3D or HFSS to export S parameter or RLC values
Sir, I am trying to do simulation of a pancake coil and a steel disk in eddy current solution type. when i was trying to give excitation at the coil terminal, this error is coming " excitation may not be assigned on non modal objects. what does this mean? what mistake i have done? please let me know. thank you sir
Dear Kamyar,
I designed a single-phase transformer in maxwell2d and imported it into simplorer. Source voltage (connected to primary) in simplorer has a pi/2 (90 degree) phase, so i expected that inrush current would not occur. But it occurs whatever i do. However, in maxwell2d, inrush current does not occur if the phase is pi/2. I cannot figure out what to do, do you have any idea? What should I do to avoid inrush current in simplorer?
Thank you so much for your tutorial video, it is helpfull.
Add some series resistance see if that helps
Hi, I am currently doing research using Ansys simplorer co-simulation. Can you guide me how to download the software?
legally through Ansys Customer portal
Hello sir, please what version of simplorer and maxwell did you use in your video?
+mark ofori-oduro Maxwell 14 / Simplorer 11
When i click add transient cosimulation, the coil is append but it do not have the pins to connect with simporer circuit, i am working in version 19, thanks!
i have been working the same problem for five days. Have you solved the problem. İf you solved, can you tell me how did you this?
@@yunusdemirci1861 Yunus bu sorunu halledebildin mi acaba ?
@@buraktasova2202 merhabalar yapalı baya oldu o yüzden tam hatırlamıyorum. Sizdeki sorun neydi tam olarak?
Mr. Kamywar when I tried to ask the maxwell co-simulation circuit, I only get one terminal. I don't get 4 terminals like you do, can you please help me on what I could have done wrong here? Thank you
+MoeAzizBadawi Hi,
make sure that you define windings for all excitations and make sure that you set the windings to external current.
in te simpler try to delete the sub circuit and replace it by new one.
hope it helps.
+kamyar K it worked thanks a lot. I just have 2 small question if possible, I have designed a Class E inverter and I like to use it as my power source. The output of the inverter is High freq1 MHz current, I connected to the along the circuit instead of the Voltage source, but I'm not getting any proper outputs for the power efficiency. Is there a reason behind that? One more thing how could generate A PWM output to driver a power MOSFET any idea? I just copied one the block designed for an example.
Thanks a lot, I know this is a lot. I apologize for that, but I really need to get a decent output to use for my project.
MoeAzizBadawi hi,
Make sure that the inverter can support tgr current that is required by your sub circuit terminals. If you are making a resonator and its a series resonator at the frequency of resonance you have short circuit. That can cause problem.
There is pulse source that you can easily use it as pwm. If I understood your question rightly. Do you mean how you can do it in simulator not real life right? In real life you can use a bjt to drive the pwm pulse coming out of the micro. Or simply by a driver and use that to buffer the gate of power MOSFET.
in maxwell version 16 how can make two port co-simulation?
Dear sir, Thank you so much for your very helpful videos. I am working on Wireless Power Transfer. I have faced some problems while I was working on the Simplorer -Maxwell co-simulation. Will you please clear me the idea about the Winding properties and the External Source for excitation. When I put my Maxwell design into the simplorer, no pins were shown to connect.And one more query where can I get the next episode of this video I mean the result part
+ismat zareen make sure you check the maxwell simplorer check. I described that in the tutorial.
Hi Kamyar,
Thanks a lot for the great tutorial! Very helpful indeed.
I have the same design in Maxwell and also the same circuit in Simplorer. However, when I try to import the Maxwell design into Simplorer, it doesn't have ports for connection. I have tried changing various settings and configurations but nothing is helping. When I import from Maxwell, I get a box in Simplorer with no ports for connection so cant proceed from there. Any help form your would be highly appreciated!
I looked at all of your previous comments and found the answer in one of them. The terminals appeared when I set the winding as external instead of current (right click on winding, go to properties and select external in the type). Thanks a lot!
make sure in Maxwell you define a Matrix under Parameters (post parameters)
Hello Kamyar K, I was using ANSYS 18.0.0 version All simulations at MAXWELL tool goes perfect, when I am going to simplorer i design the circuit bs when clicking on simplorer circut --> subcircuit--> MAXWELL components there is no Add dynamic inductance we have Add dynamic magnetostatic
Can you help me ???
Ahmad Roumeih maybe because you don’t have a setup in your Maxwell design that are importing.
Dear sir，
I‘m simulating the transformer with maxwell+simplorer and simulink.But after a few hours the start of simulationI encounter the software error:
buck_simulink (D:/co-simulation/buck/0.2/)
buck
[info] Compiler completed successfully. (10:23:36 下午 五月 12, 2016)
[info] Analyzing... (10:23:37 下午 五月 12, 2016)
[error] [Sim2000] Error - FEA1: ????????????????? >> Calculate (2:02:37 上午 五月 13, 2016)
[error] [Sim2000] Error 11557 - Error encountered in the Simulate function of user model. Model: FEA1.MAXWELL >> Calculate (2:02:37 上午 五月 13, 2016)
[error] [Sim2000] Error 13431 - Fatal error encountered while updating models. Model: FEA1.MAXWELL >> Calculate (2:02:37 上午 五月 13, 2016)
[error] [Sim2000] Error - Error while updating model values and states. >> Calculate (2:02:37 上午 五月 13, 2016)
[error] [Sim2000] Error 10564 - Simulation aborted. >> Calculate (2:02:37 上午 五月 13, 2016)
and the simulation stoped.I don't konw the reason. Could you help me ?
+Paulway Zhu I think you need to save the maxwell girl in a folder that is all Latin characters.
How you design two port blocks?
hi...
would u plz guide what kind of results (data table) we should consider or check after transient analysis..
Please refer to third parts of the tutorials. You will find the answer.
+kamyar K dear for dynamic analysis i have seen 3 parts...
is there any other part for transient analysis...? if yea plz share its reference...
thanx in advance
Check your Mesh for sure. Transient simulation only uses the initial meshing.
Chapter 4 is all about transient simulation. You can also find the playlist for transient simulations. Is that what you asked ?
Dear i want to ask about transient analysis for WPT....
May u feel my question silly but i am confused that what kind of results we can obtain from transient analysis of WPT..like L, flux linkage, losses etc.
2-Another thing i want to ask is that how can we find inductance of coil on certain frequency like for 100khz..?
Dear Kamyar
I have designed PM motor in maxwell and inverter in Simplorer. I am using cosimulation and everything works fine. But I have seen many places that people attach a resistance and an inductance in series with each phase of the machine. Why is this resistance and inductance needed? Is this the resistance and inductance of machine windings itself or what else? Because I am not using any resistance and inductance in my circuit and this may affect the system analysis
Hi ,
In the upcoming tutorial that I am uploading I will go over this in detail. But generally those are the parasitic inductors that you may have and the winding resistance. In the maxwell the winding resistance is not being calculated unless you provide it. does it answer your question?
+kamyar K
thanks for your kind response. please tag me the tutorial in which you discuss this issue.
Please find the tutorials that will be uploaded this week
Dear Sir, your video on Maxwell are awesome! I am having some troubles about the cosimulation of a switched reluctance machine Maxwell file and the corresponding drive in simplorer. The maxwell simulation is transient since I need to rotate the machine. I have got the following three error. Could you please help me? Thank you!
Error - FEA1: ERROR - could not find a transient operating point before launching Maxwell >> Calculate
Error 11557 - Error encountered in the Simulate function of user model. Model: FEA1.MAXWELL >> Calculate
Error 13431 - Fatal error encountered while updating models. Model: FEA1.MAXWELL >> Calculate
Error 10564 - Simulation aborted. >> Calculate
Hi,
I got the same error. Did you solved it?
+Fernando Baneira yes watch till the end of video.
Hi, I have some more Errors:
Error - FEA1: an existent connection was closed by the remotehost. >> Calculate (translated from german)
Error 11557 - Error encountered in the Simulate function of user model. Model: FEA1.MAXWELL >> Calculate
Error 13431 - Fata error encountered while updating models. Model FEA1.MAXWELL >> Calculate
Error - Error while updating model values and states. >> Calculate
I have build a simple circuit with two parallel coils and a data signal for the voltage. At first glance, it looked like, that maybe the connection to the licence server or some kind of overload could be the reason. I could not find any numerical problems, but I repeated it with different setting for minimal and maximal time step and it resulted in the same abortion around the same simulation time. The data signal is constant between 3.5 ms and 10 ms, the error occurs around (8.5+/-0.3) ms, so I think it should be a numerical issue. Any idea, what could be the reason for this error or some tipps, where to check?
Hi,
Did you solve this error?
Thank you
would you provide the ansys simplorer software download link from where i can download it free
Hi Mr. Kamayar,
I have Ansys Maxwell version 16, it it possible to learn me how I can make two port co-simulation, please?
Hi Mr. Kamayar,
When I run analysis in simplorer with maxwell 3D, such kind of error occurs.
The source design for Simplorer is required to have transient-transient link enabled.
Simulation completed with execution error on server.
An external simulator couldn't be setup for simulation.
If you don't mind, could you please have a look to these error.
I cannot find how to solve it.
Thanks you.
Watch the co-simulation tutorial and you would see you need to check a check box in maxwell design setting before you Be able to run the cosimulation. Check the very early videos of mine about co-simulation.
hi
I am having this error, "Simplorer requires the source solution 'Setup1 : LastAdaptive' to have a frequency sweep of at least '20' points". The frequency I am using is 2.5 kHZ.
Dear Sir. Thank you for you video. I meet a problem about the co-simulation. When I add Maxwell component, the message in simplorer have an error: Unable to find model 'MxTranTranData', please check your configured libraries. and the model in schematic has no pin to connect with circuit's other part. Please help me with some advise. Thank you very much.
王宇辰 Hi,
make sure you are making windings and assigning the excitations to the windings and MAKE SURE IN WINDINGS PROPERTY YOU ARE SELECTING EXTERNAL SOURCE FOR THE EXCITATION. if you dont set the external it would not give pins.
let me know if it hasn't fixed yet.
***** I fixed it by set the winding property to external. Thank you very much.
Hi Kamyar, I am trying to find that video where you explain external circuit excitation in Maxwell, but I can't seem to find a video title that fits this. Could you tell me which video it is?
please find actuator with magnetoeststic or transient simulations.
How to calculate mutual inductance using transient solution
Dear Sir, I am getting the following errors while doing a transient transient cosimulation.
What may be the reason for these ?
Error 13431 - Fatal error encountered while updating models. Model: FEA1.MAXWELL >> Initialize
[error] [Sim2000] Error - Error while updating model values and states. >> Initialize
[error] [Sim2000] Error 10523 - Error encountered while initializing the simulators. >> Initialize
[error] [Sim2000App] Error 10533 - Error encountered during INIT. >> Initialize
+Srijan Datta this happens when you have nested capacitors without initial values. Remove unnecessary caps and put a cap very small with initial voltage on floating nodes. That should help you to do the sim.
Yes Sir I did as you told. Now its working fine. Thank you very much for your response.
@@srijandatta5486 I met the same problem. What I should do bro?
Excuse me, does anyone have the download link for ansys simplorer or/and maxwell ?
Hello dear friend, I had a full version of simplorer 7 but I lost it, and I need it necessarily, could you help me to get it? thanks
HELP! When I try to import my 3D design to Simplorer, its dont find the model.. The error is: "You must select a design" I did step by step, but it doesn't work. Anyone can help me? Thanks.
+Renata Rezende Reis in simplorer you don't import a step file. In maxwell you import the step file and in the simplorer you import the maxwell setup file.
Please watch again
The "design" and "solution" box are empty. My windings are external type.. and I've enable the link with simplorer... I dont know whats going on!
+Renata Rezende Reis I do have personal training program but it's not free
+Renata Rezende Reis I do have personal training program but it's not free
Thanks. I'll try again!
how to get ansys simplorer
Mr Kamyar, When I'm trying to add the maxwell sub circuit to the simplorer circuit it doesn't generate details and cannot add the sub circuit saying that "You must select a design". Can you please point out me the thing that I'm doing wrong?...
If anyone knows it would be a great help.
Would you talk louder please...geezzz
sir,how can i get ansys simplorer software