Getting Started with ESP32 CAM || With the solution for Fatal Error || Rudra DIY Crafts
ฝัง
- เผยแพร่เมื่อ 21 ก.ย. 2024
- Hello everyone welcome to a fresh new video of Rudra DIY Crafts.
Today we are going to get started with the ESP32 Cam Board. Here you can watch the Intro to ESP32 Cam. Then we will discuss about How to solve The Fatal Error problem while uploading the Code.
Copy & Paste this link in ArduinoIDE - File - Preferences - Additional Boards Manager URL - dl.espressif.c...
Full Blog and Circuit : www.embeddedbr...
Hopefully you liked the video then click on the like button and Don't forget to subscribe and share ...... Yes also click the bell icon to get instant notifications.... Click on these following links to be connected with me on Social media platforms .. 👇👇👇
Facebook -
My FB page - / rudradiycrafts
Twitter -
My Twitter _ / rudraswarup99
Instagram -
My ID - / rudra_swarup
My Page - / craftechfacts
TH-cam -
Primary Channel - / @embeddedbrew
Second Channel - / @rudraswarup
So friends Thank you for watching
Rudra DIY Crafts
Imagine N Innovate
#rudradiycrafts
#ESP32cam
#fatalerror
![[SOLVED] ESP32CAM Error - Failed to connect to ESP32 Cam || Problems Uploading Code to ESP32 Camera](/img/n.gif)
Very happy to see detailed explanation from our homeland
Thank you 😊
It is working perfectly
Thanks for clearing my doubt
I am gettimg error message as No serial data received, uploading error : exit status 2
Informative One 👍
Thank you ❤️
very nice video! Keep it up!
Very nicely explained👍
very nice sir
Thank you
Nice one😲🤟
Thank you
I got some many idea's for this camera !
No serial data received is the error what is to be done to resolve
Did you find the solution? I have the same problem.
Any one solution pleasee
@@cvvahhggg2800 I fixed the problem.
1 - set FTDI's jumper to 5v and use 5v pin of esp32-cam instead of 3v pin. (This part you have to do at your risk !!!)
2- gpio 0 connect to ground
3 - FTDI's rx to tx of cam and FTDI's tx to rx of cam.
4 - upload the code.
5 - Ignore pressing reset button. Just wait and it will eventually upload the code.
Once it successfully upload the code, remove FTDI and also remove connection between GPIO 0 and ground.
Then use 5v adapter to supply power to the cam. This will also generate a lot of heat to the camera. So put a fan behind the camera to keep the temperature low.
I got mine to work with CameraWebServer sketch. But video quality is really bad and lagging.
I probably need to use external antenna. But it's not easy to desolder that 0 ohm resistor.
Nice moustache sir, and also nice informative video
Hope our college teaches and explains like you
Pitwaane ka irada he kya 😂
Thank yo Sir for the Good video
I am getting 'no programmers available '
And an error :fd_forward no file in directory
What should I do....?
May be ,This is bcoz of the Library. Try updating the Library
in serial monitor it's showing lots of question marks and square signs after pressing reset button what to do plss help
May be you haven't choosen the right baudrate
its showing me error at camera_pins.h how to solve it please respond its important for my project
sir plzz help i ahve uploaded code and when i connect to breadboard the bot is not running
plzzz help me sir
[E][camera.c:1113] camera_probe(): Detected camera not supported.
[E][camera.c:1379] esp_camera_init(): Camera probe failed with error 0x20004
how to solve this error?
I have error 'fatal error during uploading the code'.
Not resolving i have done:
1. Perfect connections in all io0 to gnd.
2. 5v supply in ft232rl to 5v in esp32 cam.
3. Installed driver ftdi and corrct port com3.
4. Also checked voltage output across ftdi.
Still not working please help with a solution.
sometimes improper json in preferences could cause such issue and need to press reset button while code uploading even you short I0 to GND
@@govtjob4913 the board was gone sir i tried all things
How can I contact you... thanks!
Can contact via Instagram.. link in description
Can we mobile Hotspot to connect to esp32 camera?
Yes .. I'm already using Mobile hotspot
@@EmbeddedBrew I'm still unable to solve Fatal error. Plz help.
What is that cable you connected to FTDI name please
It's the same cable used in Arduino Nano
USB cable type - Mini USB
madi chala
Je baaat
Bro in serial monitor it's showing lots of question marks and square signs after pressing reset button what to do plss help
Try to change the BaudRate
@@EmbeddedBrew it worked thanks brother
how do you change the baud rate?
@@kripsonxgamer7780 in serial monitor, right side baud rate will be there
Fatal error problem is not solving bro
Time out waiting for packet header is showing
time out is beacuse you might not pressed reset button while code uploading.
Hi sir , my code was uploaded and shown done uploading. Then i open serial monitor and press reset button..but shows"rst:0×1(POWERON_RESET),boot:0×3(DOWNLOAD BOOT/UART0/UART1/SDIO_REI_REO_V2)
waiting for download" ...how to solve it and get ip address??
Do just one press on the button
@@EmbeddedBrew then the mentioned statement comes for once and nothing changing
Instead of ESP32 Wrover Module choose the board as AI Thinker ESP32 Cam. Do the same in the code as well ..it should work after that.
@@EmbeddedBrew already using AI thinker esp32
Thank you
I still couldn't get into flashing mode. I don't know what's wrong
If u r getting the fatal error.
Instead of "ESP32 Wrover module" as board Choose "AI Thinker ESP32 Cam"
@@EmbeddedBrew also need to press reset button while uploading the code
I have tried this but got error message as No upload port provided & ESP32 not connected
Try looking in device manager and check if the device gets connected, if not, try identifying the driver for your esp
Sir, I have 1 module. I have also got the error but it dod not resolve. HERE IS THE list of tried solution:
1. Connecting capacitor between En amd GND pin. 2.repeat whole process. 3. Press boot button while showing "connecting.."
4. Tried using esp32 c module base /adapter board
5.changing Module selection in IDE, 6. NEW ftdi, new cable,
7.Two voltages 5 v, or 3.3V,
8 external power supply,
But still error persist.
Does this module has an internal memory issue? Will the whole issue can be solved if I upload bootloader and repeat whole process? If yes, then how?
Same issue with my new esp32 cam
Where you taken the ssid and password?
This is the Wifi and password of your Router or mobile Hotspot.
@@EmbeddedBrew Now its showing --fatal error occured. Failed to connect Esp32 . No serial data received .. what to do?
Check the connections again ..
Then Choose the board as AI thinker camera module from the list and in boards section.. then you can upload
Where u bought it?
Amazon has them
still same error occuring
If ur getting the fatal error. Instead of "ESP32 Wrover module" as board Choose "Al Thinker ESP32 Cam"
Thanks. Still doesn't work.
If u r getting the fatal error.
Instead of "ESP32 Wrover module" as board Choose "AI Thinker ESP32 Cam"
@@EmbeddedBrew First thing I tried:-) After trying dozens of suggestions online, I think the CP2102 adapter is bad, so I ordered a ESP32-CAM-MB programmer.
And the ESP32-CAM-MB worked beautifully:-)
hello i havethis problen any solution please
[E][camera.c:1113] camera_probe(): Detected camera not supported.
[E][camera.c:1379] esp_camera_init(): Camera probe failed with error 0x20004
change board name to wrover from AI also try to downgrade esp32 to lower