Artillery Sidewinder X2 - 3D Printer - Unbox & Setup

แชร์
ฝัง
  • เผยแพร่เมื่อ 11 ธ.ค. 2024
  • Artillery Sidewinder SW-X2
    Amazon: geni.us/CbjdjAI
    or: geni.us/zUcEXW
    Aliexpress: www.aliexpress...
    Recommended: geni.us/JustVlads
    Artillery official website: www.artillery3...
    Artillery Sidewinder SW-X2 3D Printer Latest Model Ultra-Quiet Printing 300x300x400mm Automatic Leveling Power Failure Recovery 95% pre-Assembled 110V-220V Free Switching
    The print speed can reach up to 150 mm/s, and with the Direct Drive Extruder, makes high quality print, especially for flexible filament. When it arrives on your doorstep, the Sidewinder X2 comes 95% pre-assembled, which makes installation easy as can be.
    The printer has a direct drive extruder and a fast heating AC heat bed with built in thermal runaway protection, even if the board or the SSR malfunctioned, the bed won’t heat up endlessly until bad things happen. With the Lattice glass smooth headbed surface, it makes all types of filaments can be easily stick on.
    There are 3 inductive sensor end stop separately set on XYZ axis while those non-touch, high-precision limit switches can automatically calibrate and maintain good stability under high-speed printing. Most importantly, features Synchronized Dual Z System greatly increase its printing stability.
    SW-X2 will save you from the loss of power. When it recover from a power failure, the machine will continue to print. Also, it will automatically pauses your 3D print and notifies you when you've run out of filament, saving you time and money.
    With a 300 x 300 x 400 mm build volume, the Sidewinder X2 3D printer has a hushed operating sound even working at fast speeds, thanks to its exclusive ultra-quiet stepper drivers which significantly reduce the noise level.
    SW-X2 overhauled the motion system on the Z, replacing the lead screws with a belt-driven system, which not only reduces the noise level but also allows for faster print speeds.
    As an Amazon Associate I earn from qualifying purchases
    My website: www.justvlads....

ความคิดเห็น • 115

  • @JustVlads
    @JustVlads  3 ปีที่แล้ว +4

    New Channel: www.youtube.com/@Just_Print
    SW-X2: geni.us/CbjdjAI
    Recommended: geni.us/JustVlads

  • @GreySectoid
    @GreySectoid ปีที่แล้ว +19

    Just bought this as my first 3d printer, the assembly wasn't hard but your advice here was invaluable since the manual left so many important things unmentioned. Thank you!

    • @Sharpzee
      @Sharpzee ปีที่แล้ว

      hi just found this video and im looking into starting with 3d printing how is the printer after using it for some time in terms of beginner friendliness and quality

    • @omegadeepblue1407
      @omegadeepblue1407 ปีที่แล้ว

      ​@@Sharpzeeis fine, but if you are really super beginner -0% skill then you can look for a Elegoo Neptune 3 pro (you can also wait for the Neptune 4 that is going to be avaible very soon) or the Anycubic Kobra 2, those two are the most modern beginner 0% skilled user friendly, you can also look at the Bambu X1C but only if you can pay it.

    • @Kman31ca
      @Kman31ca ปีที่แล้ว

      What you're looking for is what Omega said, OR get the Bambu Labs P1P for 700$. Probably the best price to capabilities 3D printer out there.

    • @Nero_AZ
      @Nero_AZ ปีที่แล้ว

      Me to I just got my artilery sidewinder and not gonna lie the video was necessary for me lol

  • @robkuhar2045
    @robkuhar2045 ปีที่แล้ว +5

    I found the following settings best: 220 degrees extruder 65 degrees bed a light coat of hairspray. And DONT FORGET .To enable compensation for auto-leveling, add M420 S1 Z10 after
    G28 in starting Gcode.

  • @sithinthemaking
    @sithinthemaking 3 ปีที่แล้ว +30

    I was putting my sidewinder x2 together today- they've changed the assembly of the spool holder slightly from shown in this video, which threw me at first as I thought I had some parts missing! Turned out it was just I had the out-of-date instruction manual. The manual on their website was up to date and showed me how to put it together.

    • @namhi1022
      @namhi1022 3 ปีที่แล้ว +3

      Thank you for this comment. I thought I was crazy!!

    • @zfvids
      @zfvids 3 ปีที่แล้ว +1

      THANK YOU! I was typing up a support ticket about missing pieces when I decided to check the comments lol

    • @kieculpitt407
      @kieculpitt407 3 ปีที่แล้ว +1

      Same here; took me a couple minutes to realize I had the updated redesign....lol

    • @WynterNash
      @WynterNash 2 ปีที่แล้ว +1

      Me too! I was so upset thinking that I was missing those two silver tubes. I contacted Artillery support on Facebook Messenger, he sends me a video of a German guy speaking German (which I do not understand), but while watching it I figured it out. I told Artillery they should make their own video showing the update instead of wasting people's time like that. They said the updated manual did not get put in the box. What a true PITA that was! lol

    • @Redshift1360
      @Redshift1360 2 ปีที่แล้ว

      Haha same thing happened to me too, luckily I fiddled with it and figured it out before emailing support. Glad to know I wasn’t the only one who was confused😂

  • @jasonwu2758
    @jasonwu2758 2 ปีที่แล้ว +6

    The many hours you've saved people are countless. Thanks from Australia and all the 3d printing n00bs!

  • @AdobadoFantastico
    @AdobadoFantastico ปีที่แล้ว +4

    This video was so thorough, clear, but also relatively concise for what it showed. Saved me a ton of trouble, thanks.

    • @livefreeprintguns
      @livefreeprintguns ปีที่แล้ว +2

      I watched his Ender-3 video a few weeks ago... it was INSANELY good and helped me get my Neo setup way more than any other channel.

  • @MiDnYTe25
    @MiDnYTe25 3 ปีที่แล้ว +15

    Thanks for the detailed instructions on assembly, it was a breeze to put mine together and start right away! Awesome guide and video.

  • @disturbedfan545
    @disturbedfan545 3 ปีที่แล้ว +8

    I bought this a month back. Had some clogging issues form the beginning and my prints typically don't adhere well to the bed. It's all probably my fault tbh but I had the extruding gear break during a print and went through a week of back and forth to get new parts from the company. After I fixed the extruder, it runs fine. It is a very solid printer for the price and I will say probably better than most at the same price level.

  • @livefreeprintguns
    @livefreeprintguns ปีที่แล้ว +1

    It's insane how knowledgeable you area on this stuff.

  • @GaryForgingOn
    @GaryForgingOn 2 ปีที่แล้ว +1

    Thank you for the video. I just bought a sidewinder x2 and I need to pull it out of the box and set it up. This is my first 3d printer. Thanks

    • @triplethreat9168
      @triplethreat9168 2 ปีที่แล้ว

      How do you like your first printer ? I’m considering it for Black Friday sale

    • @Cosmic_Corp
      @Cosmic_Corp ปีที่แล้ว

      @@triplethreat9168 Did you get it? Im strongly considering getting one but very nervous being my firsat printer

  • @mestari33
    @mestari33 2 ปีที่แล้ว +2

    Thank you! I just got the Sidewinder X2 yesterday and this video was very useful! Thanks!

  • @adelinechung3987
    @adelinechung3987 3 ปีที่แล้ว +10

    Did you manage to find the perfect settings for the swx2 on cura?

  • @larsbliss2728
    @larsbliss2728 ปีที่แล้ว

    Mine arrived last week. I'll be setting it up this week for some fun. My first 3d printer.

  • @usmannaeem9018
    @usmannaeem9018 3 ปีที่แล้ว +8

    5mm retraction on a direct drive?should be arround 1-3 mm

    • @KxngUnkasa5
      @KxngUnkasa5 2 ปีที่แล้ว

      What do you think was causing the stringing?

  • @gotsn0w
    @gotsn0w 2 ปีที่แล้ว +8

    Excellent video! Helped me a lot with both adjusting the tension on the roller wheels and leveling. Thank you! :D

  • @pincopalla106
    @pincopalla106 3 ปีที่แล้ว +2

    Hi, I'm looking for the stl of the yellow tower you printed at 0:54. Thank you very much in advance for your attention and for the accurate review of course! ;-)

    • @JustVlads
      @JustVlads  3 ปีที่แล้ว +2

      www.thingiverse.com/thing:2647041

  • @Tensquaremetreworkshop
    @Tensquaremetreworkshop ปีที่แล้ว

    I have the X1 - look like they addressed all the problems.
    Better connectors for the ribbons (endless problems on the X1)
    Improved reel holder (was 2 hex bolts at the rear, with ball races, so you had to adjust it for each change of reel width)
    Bed power no longer sticks way out the back, making it very deep.
    Auto levelling!
    Z probe instead of a limit switch- which sometimes does not get the height correct.
    Makes it a much better printer

  • @JD_Manufacturing
    @JD_Manufacturing 3 ปีที่แล้ว +6

    Retraction needs to be at 1.5 mm

  • @ytmB4HyU4kUq
    @ytmB4HyU4kUq ปีที่แล้ว

    Thanks for this. Mine just arrived today and the curved exhaust tube snapped off, luckily it was a two piece component anyway, so it looks like it can just be super glued back on. I'm looking forward to using this printer!

  • @moonobservergilles5730
    @moonobservergilles5730 2 ปีที่แล้ว +1

    why they insist placing the filament roll on the top? center of gravity is high and could affect the final printed product?

  • @TheBehnjamin
    @TheBehnjamin 2 ปีที่แล้ว +4

    hey really finding your video useful, they should hire you to make official manual in video form!
    one question: i didnt see you add in the gcode in cura for making use of the auto leveling bed? in the manual it says to add "M420 S1 Z10" after G28 in the slicer.
    is this necessary? wont omitting this coding completly negate any information gathered by the auto bed leveling?
    sorry if i missed. you are amazing.

  • @shaunpalmer9474
    @shaunpalmer9474 ปีที่แล้ว

    Cheers Vlad My Anet ET4 just stopped working so I'm getting a new printer , looking for a larger platform saw this in an online catalogue and thought of your channel, your review just sold me on it. Thanks:-)

  • @FranklyWry
    @FranklyWry 3 ปีที่แล้ว +4

    Do not throw away the filament! Use a desiccator like Camp-Dry and a container that can accommodate the spool; the filament may have soaked up a lot of moisture.

    • @JustVlads
      @JustVlads  3 ปีที่แล้ว +4

      Tried drying out for extended periods with no luck. Instead of tossing it I will use it for crude modeling.

  • @snake_doc1788
    @snake_doc1788 2 ปีที่แล้ว +2

    My experience with direct drive is to use a 1.5 - 2.5 retraction setting. Can anyone else confirm that Vlad retraction settings seem much too high? Bowden tube levels of retraction seemingly...

    • @Hanzi2u
      @Hanzi2u ปีที่แล้ว

      As a direct drive user , mine is 0.8 which is for my ender s1 pro , I bought a x2 today so I'm gonna try that aswell but I'll find out when it arrives

  • @phantomrose1999
    @phantomrose1999 3 ปีที่แล้ว +1

    Just got one, very easy to setup and print from FreeCAD to Cura to the printer, but i have such a dumb question, HOW TO TURN IT OFF ? i killed the big switch at the back, but its still on !!! LOL

  • @sebastianmiller7740
    @sebastianmiller7740 3 ปีที่แล้ว +1

    That intro was amazing!!!

  • @ThePunksta333
    @ThePunksta333 ปีที่แล้ว +1

    Thank you for this exceptional video. Much appreciated.

  • @ChinaAl
    @ChinaAl 2 ปีที่แล้ว +1

    Wow! Fantastic video. I got to save this because I'm getting this X2.

  • @telum2265
    @telum2265 ปีที่แล้ว +1

    Best exaplanation

  • @nathanlouvros9382
    @nathanlouvros9382 3 ปีที่แล้ว +2

    What would you prefer between this and a Cr10s pro v2?

  • @JohnHilman1968
    @JohnHilman1968 3 ปีที่แล้ว +2

    Turn down the hotend temp. PLA at 210 is mych too hot. 190-200 is about the right spot. Less stringing. Less pock marks in the prints

  • @EasiaGordonSheu
    @EasiaGordonSheu ปีที่แล้ว

    謝謝!

  • @jolebole-yt
    @jolebole-yt 3 ปีที่แล้ว +2

    I'm stuck at part 1. I am missing 2 screws for the spool holder. Great job Artillery :(

  • @bluedragon77
    @bluedragon77 2 ปีที่แล้ว

    i dont think i have the metal parts for the spool holder. didnt know about them till i saw your video..

  • @rockman49er
    @rockman49er ปีที่แล้ว

    You didn't show how you got the rest of that print off the bed the little circle I just printed the sample cube and I could barely get it off now I have that little square line stuck to my bed how do I remove it from the bed I'm stumped and don't want to scratch it anymore than I already have with my spatula

  • @Enjoymentboy
    @Enjoymentboy 3 ปีที่แล้ว +4

    I've been looking at this for my foray into 3D printing and this video really helped clarify things for me. Appreciated. So many options out there it is very daunting to jump in. What would you recommend for software to go with this printer for a beginner?

  • @Landos_authentic
    @Landos_authentic 3 ปีที่แล้ว

    Idk if 1 hour and thirty minutes is fast or not for a benchy but I’m slinging them out just under a hour with better quality, I’m looking for another printer that isn’t a delta because I want a direct drive extruder so I can print with TPUs. Granted I probably can with my Boden extruder I just haven’t tried it yet

  • @wskwong2000
    @wskwong2000 2 ปีที่แล้ว

    7:13 I don't feel the bed jump when I push manually but my print (especially the flat ones) have a horizontal ripple pattern (but not because of overextruding) . Any ideas?

  • @robkuhar2045
    @robkuhar2045 ปีที่แล้ว

    My filament does not attach to the center of the bed but is fine on the edges. Can the bed be bent?

  • @kristinebaxter8867
    @kristinebaxter8867 11 หลายเดือนก่อน

    the travel speed isn't showing up. How can I see the speed with this?

  • @gladiatormechs5574
    @gladiatormechs5574 2 ปีที่แล้ว

    QUESTION.. do both the X-1 and X-2 have 4 stepper drivers that are plug in ? So if you have a layer shifting problem do you need to replace all 4 at the same time.. Because you wont really know which one of the 4 drivers is causing your intermittent problem of layer shifting.

  • @ChinaAl
    @ChinaAl 2 ปีที่แล้ว +1

    I always had retraction between 1 / 1.5 for direct drive. Are you going the wrong way going 3 to 5?

    • @Hanzi2u
      @Hanzi2u ปีที่แล้ว +1

      Yes hes wrong.

  • @BackYardPropsWA
    @BackYardPropsWA 2 ปีที่แล้ว

    At trying to level the bed and it doesn’t seem like the leveling knobs make any sort of difference? The nozzle grabs the paper and I cannot slide it around no matter how loose or tight the leveling knob is

  • @91rickstar
    @91rickstar 2 ปีที่แล้ว

    @Just Vlad is it normal for the extruder arm the part with the extruder on it if you grab the arm and twist is back and forth should it move mine moves does this need fixing if so how do I fix it I also have a ghosting issue on details such as holes text and other shapes how do I fix that this is a new 3D printer it’s been one thing after another

  • @Nicoricanmarxist
    @Nicoricanmarxist ปีที่แล้ว

    Hey great review. Would you recommend the X2 or the Ender 3 Max neo?

  • @ronbray6778
    @ronbray6778 2 ปีที่แล้ว +1

    Great video as always. Can you put a link to the Test files you use? I would like to use them as well.

  • @joeynelson5245
    @joeynelson5245 2 ปีที่แล้ว

    Do you have a video for the anycubic vyper 3d printer? I was looking for it in your video section but I can not seem to find a video. I also have the artillery sidewinder v2 and in your video about the printer when you were setting it up in cura 4
    5.1 was what I need for anycubic vyper

  • @jason401.
    @jason401. 3 ปีที่แล้ว +2

    3:51 1GB?

  • @drea217
    @drea217 2 ปีที่แล้ว

    very very gooood, thaaankss maan

  • @supahfly8067
    @supahfly8067 9 หลายเดือนก่อน

    When i home the plate it goes to the center like yours, but then when i want it to go to the corner it goes to the right and completely off the plate, then down and tries to keep going even though it is already at the bottom. can anyone help with this?

  • @luisfelipejahn1281
    @luisfelipejahn1281 ปีที่แล้ว

    14:07 mine are so tight that it ripped the threads off the screw

  • @AlejandroVales
    @AlejandroVales ปีที่แล้ว

    All those bubbles are many times because of the Shit quality USB stick, if you use one that is quicker or you disable the "power down safe mode" which writes to the USB to save the position of the printer it will print almost perfectly

  • @dinodolic2270
    @dinodolic2270 2 ปีที่แล้ว

    which 3d printer would you recommend as the first 3d printer? for hobbies.

  • @JSTidbitqueen
    @JSTidbitqueen 2 ปีที่แล้ว

    Thanks for such an informative video.

  • @jodrafting
    @jodrafting ปีที่แล้ว

    looks way better than my ender 3

  • @mariusc2137
    @mariusc2137 3 ปีที่แล้ว +1

    I think I.ve watched all your 3d printers reviews for the past couple of months and im now really looking to get one myself. The thing is I need a big bed like this but I just cant find any videos on how it performs with PETG or ABS since those two would be my main filaments (I need functional parts). How does this one perform? CR10 V3 would be a second choice but aparently not much info on how it prints abs/petg either... bummer

    • @terriblelottery
      @terriblelottery 3 ปีที่แล้ว +1

      Did you find an answer? I just purchased this printer

    • @mariusc2137
      @mariusc2137 3 ปีที่แล้ว

      @@terriblelottery I saw your comment late, sorry. I ended up getting the Ender 5 Plus

  • @Hanzi2u
    @Hanzi2u ปีที่แล้ว

    I print benchys in around 51 min , on a creality s1 pro... stock.
    Can't Imagine waiting 3 hours for a fkin benchy lol

  • @CaffeinatedFrostbite
    @CaffeinatedFrostbite 2 ปีที่แล้ว

    what is your minimum extrusion distance withdrawal? mine was 10 by default and it was highlighted in orange

  • @craftsmanchris7
    @craftsmanchris7 ปีที่แล้ว

    Hi man, awesome videos. I am between the Artillery Sidewinder X2 and the Creality Ender 3 S1 pro. Which one would you recommend? This will be my 1st 3d printer.

  • @aberodriguez4149
    @aberodriguez4149 2 ปีที่แล้ว

    Thanks for the work and information you put out. Could you tell me which filaments you used on your red frog, the spaceman and your rocket much appreciated. Great video I am still undecided which 3D printer I will go for but this is one to consider. Thanks again.

  • @Tech-Domination
    @Tech-Domination 2 ปีที่แล้ว

    Thank you for the video , can i print own models ?

  • @lyudmilamandzyuk155
    @lyudmilamandzyuk155 3 ปีที่แล้ว +1

    This is so cool 😊! .. so fun to watch

  • @livefreeprintguns
    @livefreeprintguns ปีที่แล้ว +1

    42:40 Snaggle-tooth shark! 😆

  • @mgpmbass3616
    @mgpmbass3616 2 ปีที่แล้ว

    Any concerns if the Z axis bearing supports in that upper plastic arm will quickly wear out? And how is Artillery's customer support?

    • @lefizz55
      @lefizz55 2 ปีที่แล้ว +1

      The amount they turn they'll last basically for ever.
      You get the same type of bearings in motors which see more action in 5 minutes that these will get in years.

  • @notchipotle
    @notchipotle 3 ปีที่แล้ว

    I got some weird bulging on the bottom solid layer, I tried to set the z offset way too far but the bulging is still there

    • @wskwong2000
      @wskwong2000 2 ปีที่แล้ว

      Same here. Did you get it resolved?

  • @hudenmann
    @hudenmann 3 ปีที่แล้ว +1

    Thanks for this video! Exactly what I was looking for. :-)

  • @andersjohansson1889
    @andersjohansson1889 9 หลายเดือนก่อน

    A nice premium feel. Hehe. 😄😄😄

  • @bradley9856
    @bradley9856 3 ปีที่แล้ว

    mine prints its first layer WAY to high and I cant figure out how to change it

    • @GAMERGEBITER
      @GAMERGEBITER 3 ปีที่แล้ว +1

      He explained it in the video

  • @prjmayhem8323
    @prjmayhem8323 2 ปีที่แล้ว

    Thanks for the vid! did you ever find the perfect cura settings?

    • @ultimategamer3212
      @ultimategamer3212 2 ปีที่แล้ว +1

      There is no singular perfect cura setting it mostly depends on what your printing.

  • @Joeyfordayz2301
    @Joeyfordayz2301 3 ปีที่แล้ว

    Mine didn’t come with a test model

  • @aliceyu1939
    @aliceyu1939 3 ปีที่แล้ว +1

    great review !\

  • @forbiddenballer8671
    @forbiddenballer8671 3 ปีที่แล้ว

    How to make shark 0:45

    • @JustVlads
      @JustVlads  3 ปีที่แล้ว

      www.thingiverse.com/thing:3845304

  • @jonygry
    @jonygry 2 ปีที่แล้ว

    Take a shot every time he says "so yeah"

  • @333cgs333
    @333cgs333 3 ปีที่แล้ว

    Awesome video. What filaments does the printer take?
    Also what is your top recommended 3D printer for a newbie? Thx!!

    • @ultimategamer3212
      @ultimategamer3212 2 ปีที่แล้ว +2

      This printer is probably the best for newbies although it has some minor problems which could be easily fixed. These printers are capable of using any filament. I would recommend Pla if youre printing indoor.

    • @333cgs333
      @333cgs333 2 ปีที่แล้ว

      @@ultimategamer3212 thanks a lot for your replu

  • @ricstanden
    @ricstanden 3 ปีที่แล้ว

    Pretty sure the thumb drive says 1gb

    • @Hanzi2u
      @Hanzi2u ปีที่แล้ว

      Lol

  • @doverivermedia3937
    @doverivermedia3937 2 ปีที่แล้ว

    Whats the point of 400mm in Z if it fails. This is symptomatic of revues. Pick out the good bits and gloss over the junk. Makes my first 3D printer choice real headachy. jeez 😳 .... 🇬🇧

  • @Yasin.M86
    @Yasin.M86 3 ปีที่แล้ว

    ❤️❤️

  • @vinceramdhanie4210
    @vinceramdhanie4210 2 ปีที่แล้ว

    brother man your video is good information but you talking to much and to fast

  • @RyanDurbin10
    @RyanDurbin10 2 ปีที่แล้ว +1

    My sidewinders print at 150mm/s+..... Lol

  • @makewithmegma
    @makewithmegma 3 ปีที่แล้ว

    🔥💕😍👌👍

  • @gamergod1130
    @gamergod1130 3 ปีที่แล้ว +1

    can it print ghost guns

  • @Aliye727
    @Aliye727 2 ปีที่แล้ว

    you print very bad, ı open and directly give print and resukt is exellent

  • @jc-lz5tf
    @jc-lz5tf 9 หลายเดือนก่อน

    Why is everyone printing those god damn useless baby toys???😮