If the bulb is a halogen, then yes it is possible. However, if it is a factory LED, this bulb would be soldered to a chip and board, and you would not be able to swap it out.
Would have been a lot more helpful had you shown installation on the driver's side of the car. The passenger side is of course the easy one with a lot more room available to work. Also a close-up demonstration of pushing or squeezing the tab on the power connector would have been very helpful in my opinion. It's not obvious as you make it out to be. Have seen a lot of your videos and the majority of them are very good but for this one small omission about the tab on the power connector this one is another winner thank you.
Thank you for the interest. We will keep an eye out for an Avalon out here in Los Angeles for an installation video. However, please note, the installation process is very similar for all vehicles. I would recommend having a watch of some of our other DIY videos, and you should gain a general knowledge of how LEDs are installed.
I know your bulbs are 3200lm/LED, however other premium lights offering 2400lm/LED bulb. On the video and photo those 2400lm look really bright and 3200 should be even brighter. I am afraid that 3200lm are going to be too bright. Would you agree or disagree? Thanks
Absolutely not. If you are concerned about glare projecting into oncoming drivers, there are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID/LED lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K lights on the road because they are more natural to the human eye. For this reason, we only carry the 6000K color temperature for our headlights.
Does this void your warranty with Toyota? I have a leased camry and I want to know if they'll create any problems if I install this in my leased 16 camry.
No, upgrading your lighting will not void your vehicles warranty, as it is protected by the Magnuson-Moss Act. I have linked some information on this law below for your convenience. www.impalaclub.com/naisso/magmoss.htm
Glad to hear! We hope the install goes smoothly! At Precision LED, we proudly stand by our products, which is why we offer a limited lifetime warranty on all our LED bulbs. Please let us know if you have any issues or concerns!
I installed some LED headlights on my 2015 Camry, but I have an issue where my high beam lights flicker when acting as daytime running lights. I believe it's caused by the decreased voltage being sent to the bulb during DRL use. I purchased anti-flicker decoder modules and wired it up between the power supply and the LED driver, but it just made it worse and caused the light to not work at all. I need some help here cause I just don't know what to do. The lights I got are the Hikari 2023 Future Titanova, and they're flippin awesome when they work right. Did I just choose bad lights?
Thank you for the interest. Yes, the package referenced in the description, as well as the installation video is indeed compatible with the 2016 Camry, as it is still the same 5th generation.
Does the bulb position while in the projector make a difference? I have the passenger side bulb facing up and the driver side is facing down. Do I need to adjust it?
When I do this install, will it affect my highbeams? Or how will my high beam look like? I currently have factory halogens only. On my 2015 camry XSE. Looking to purchase this.. and are these the same as the xenon brand led headlights?
We do have listed that your low and high beams project light from different lights. No, the headlight kit will not affect your highs at all. The high beams will remain halogen. Also, no, Xenon is a gas that is inside of HID bulbs. We only sell Premium Canbus LEDs.
I have a 2015 Mitsubishi Outlander Sport ES & I want to install led bulbs in it. Do you have a instructional video for my model of car? It has the dust/rain cap over each bulb housing. Thr cap has a wire through it already, but where will all the extra wire go & the led driver? Thank you :-)
LED headlights can cause a lot of glare on certain reflector housings. Do these work as designed by the Toyota on a Camry 2017 without all that blinding glare and/or uneven lighting patterns? Please explain.
There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K or 8000K lights on the road because they are more natural to the human eye.
There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K lights on the road because they are more natural to the human eye.
i’ve got a 2007 xle and recently bought new led bulbs for it, will i need a converter thingie or will it be just fine.. i’m sorry i don’t know much of anything about cars..
Hi, if you purchased one of our headlight kits you will not need anything extra as our kits come with built-in resistors to make the installation a very simple, plug-and-play process! If you need any help with installation please feel free to reach out to us at help@precisionled.com.
Thank you for your interest. Our LED headlamps typically last years, depending on use/battery efficiency. However, we do back all of our products with a 1 year warranty.
My 2011 came se has stock headlight lens and bulbs. Haven't done anything. So I can just purchase this kit and get right to it? Course I plan to refinish the lens. But u mentioned projection lens...
Yes, as long as you have not changed your headlight lens to an aftermarket one, our kit will indeed work for your vehicle. Our kits are designed for your stock halogen lens.
i will purchased very soon but i want the led lights also for the bottom lights in the front bumper also..its Orange doesnt look well with the leds headlights...do u have a video for that? or the led product
You can find the compatible high beam kit here: www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html And the low beam kit here: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
Hi, thank you for your purchase! We usually ship out our orders on the same day if it is a business day during business hours, but if an order is placed on the weekend or after business hours we will probably ship out on Monday.
Yes, we absolutely do. We have listed your highs/DRLs would use the 9005 bulb fitment, and you can find a direct link to the product here: www.precisionled.com/premium-9005-cree-led-headlights.html
Yes, certain model LEDs (cheaper brands, typically) are not compatible with the DRL system, and will disable this. Our LED kits will not affect the DRL.
I believe the only thing missing would be turn signal and brake lights, as we do not recommend replacing these lights. Reason being is because the electrical system will cause these LEDs to hyper flash. However, you will experience no issues with what is shown installed in our DIY videos.
No, you do not typically have to adjust the cutoff line after installation. However, I would double check to ensure it is not shining too high or low regardless.
Do you have a video of 2013 - 16 Elantra GT H7 LED ? I installed your Interior LED package on my Elantra GT , looks awesome ! Much better lighting than stock .
Thank you for your interest. Unfortunately, no, we do not have a video for the 2013 - 16 Elantra Headlamps. However, the installation would be nearly identical to as shown in this video. The only major difference would be physically locating your halogen bulb.
Hi Phil. Can you make a video on how to install led headlights for 2011 toyota corolla s and 2018 hyundai santa fe sport. Thank you and more power to you guys. 👍🏼👍🏼
We do not advertise the turn signal upgrade because it will hyper flash when ignited. We are currently searching for a solution for this so stay tuned!
Hey! I just bought the LEDs installed them in my car and hear a weird whirring noise that is kind of noticeable from inside the cabin/interior. Is this normal? I am afraid that it can cause a short or has something to do with the voltage
I do apologize for the confusion, but the CREE H11 product is currently on backorder for week, so the product has been disabled. However, I would recommend checking back in a week or so, and it should be back up. We thank you for your patience.
Unfortunately, we do not have an install video for your vehicle just yet, as we have not yet gotten our hands on one out here in Los Angeles, CA. However, the installation process is virtually the same for all vehicles. I would recommend having a watch on some of our other DIY videos, and you will gain a general knowledge of how LEDs are installed. I have linked our How-to Page below for your convenience. Also, the LED headlamps will increase your nighttime driving visibility by 2-3x. www.precisionled.com/how-to-videos.html
Thank you for your interest. Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than LEDs. I have linked some additional information below for your convenience. www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
I apologize for the inconvenience, but we currently have the CREE H11 Headlight product (item in the description) on backorder. The product has been removed from the website for a short moment. I would recommend checking back in a week to see if it is back up, as this is the timeframe we do expect to receive a replenishment of inventory. We thank you for your patience.
I apologize for the inconvenience, but we currently have the CREE H11 Headlight product (item in the description) on backorder. The product has been removed from the website for a short moment. I would recommend checking back in a week to see if it is back up, as this is the timeframe we do expect to receive a replenishment of inventory. We thank you for your patience.
Thank you for your interest. We do indeed have a headlight installation video for a Rav4, which you can find here: www.precisionled.com/how-to-videos/toyota/toyota-rav4-headlight-2005-2013.html
Our database is based off of US manufactured vehicles. It is possible that we have a headlight kit for your vehicle, however, we do not have the bulb fitment listed in our database. If you can tell us the fitment, I can see if we carry a compatible kit. You can get this information by simply reading through your Owner's Manual.
What you are referring to are grounding shadows, and are caused by the return wire that elevates just slightly above HID or LED bulbs. However, our LEDs do not come with this return wire, so you will not experience any grounding shadows, or dark spots.
Thank you for your interest. We are always on the looking for vehicles to shoot new or updated videos. We will keep an eye out for a 2015 Camry for your requested video. Subscribe for updates!
Thank you for your interest. We are always on the looking for vehicles to shoot new or updated videos. We will keep an eye out for a 2015 Camry for your requested video. Subscribe for updates!
For the high beams, you would have to install a completely separate LED kit, which you can find here: www.precisionled.com/premium-9005-cree-led-headlights.html
Thank you for your interest. I have linked the compatible kits for the headlamps, as well as the high beams below for your convenience. Both of the packages will increase your nighttime driving visibility by 2-x times. Low beam: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html High beam: www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html
Thank you for your interest. Yes, the installation would be virtually identical as shown in the video, as your vehicle would use the same H11 bulb type used.
No, our kits are designed for your stock headlamps. There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K or 8000K lights on the road because they are more natural to the human eye.
Thank you for your interest. First, you would have to ensure that there is enough room for the LED to fit into the housing with the dust cover sealed. I would say you would need an additional inch of space vs your halogen bulb into the housing. And if the LED does fit, then you would have to drill a small hole in the dust cover in order to feed the bulb wires through. Lastly, it would be important to seal the hole with tape.
This installation was for the low beam. However, the high beam is virtually identical, but you would install this kit: www.precisionled.com/premium-9005-cree-led-headlights.html
Yes, the installation process is virtually identical to as shown in the video. The only difference, if any, would be physically locating your halogen bulb.
Thank you for your interest. I do apologize for the confusion. You can find the headlamp LED product compatible with your 2015 Camry here: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
No, that would not be necessary for the Camry. The package listed in the description comes with everything you will need to successfully upgrade your headlamps to LED.
Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than LEDs. I have linked some additional information below for your convenience. www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
Thank you for your interest. No, we do not have a installation video for the fogs. However, the installation process should be identical to as shown in the headlight video. The only major difference would be accessing your fog bulb.
Thank you for your interest. Actually, the product link in the description of the video is compatible with your 2010 Camry as well, as they would both use the same H11 bulb type.
+PrecisionLED have you had any complaints from customers for getting pulled over, as the LEDs are bright similar to HIDs? Or is that mitigated due to the projector housing? I ask because my 16 CRV only has the reflected housing.
It sounds as though your H7 bulbs may require an adaptor in order to lock your lights into place. Feel free to reach out and contact us directly at help@precisionled.com. We're happy to help!
Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than HIDs. I have linked some additional information below for your convenience. Please, do not hesitate to contact us if you have any additional questions or concerns. Sincerely, Brent @ PLED www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
I believe the 2011 BMW 529i comes with stock HIDs for the low beams, which you cannot swap as the ballasts, connections, and bulbs are completely different fitments than our LEDs. Our LEDs are designed for halogen upgrades to LED.
This would definitely depend on the quality of LED headlamps you are installing on your vehicle. If you install a poor quality product, then you will indeed experience poor quality light output from your headlights. However, we believe we have some of the highest quality LED products on the market today, which we back with a 1 year warranty. I would expect the LED system installed to increase your nighttime driving visibility by 2-3x. If you are unsatisfied with your purchase, we do indeed have a 30 day, no hassle return policy.
Yes, we do indeed carry this kit, however, it is currently on backorder. We do expect a replenishment of inventory to come in within a week. The product linked in the description should be enabled back onto the website in just a couple days.
Would aftermarket LED headlight trio codes, and cause damage to my car's electrical system? I have read info that I could due to modern car's electrical "canbus" system? Thanks.
No, we only sell high quality Canbus products to ensure you do not experience any dash errors, flickering, electrical issues, or any other issues with the LEDs.
Thank you for your interest. Yes, we do have a headlight kit for your 2015 Rav4, which you can find here: www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html
The installation process for the DRLs / high beam would be identical to as shown in the video. The high beam socket is right next to the low beam socket. You would install this kit: www.precisionled.com/premium-9005-cree-led-headlights.html
@@PrecisionLED I want to order but am a little confused. I have a 2grfe 2011 camry se that I thought was a generation 6. I believe camry had a 'facelift" 2011 model but not sure if this was considered Gen 6 or 7. Either way mine is 2011 Gen 6 SE v6 Camry .. Will these work on my car ? =) www.precisionled.com/premium-h11-cree-led-headlights.html?
@@jahmosaxenamp6797 Thank you for your interest. Yes, that is indeed the correct kit for your 2011 Camry SE, as your vehicle uses the same H11 bulb fitment for the headlamps as the previous years.
Thank you for your interest. The installation process is virtually identical to as shown in the video, and you would install this kit: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
The legality varies vastly from locale to locale. You would have to check with your local laws and regulations. What is illegal in most places are the color hues, as they could project glare to oncoming drivers. As opposed to the 6000K color temperature, which is right around the color of stock LEDs. This would project a pure white and is more natural to the human eye. This is the reason why we only ship the 6000K color temperature with our headlamp kits.
Thank you for your interest. The installation process would be identical to as shown in the video. The video applies to all years 2011+. You can find a direct product link in the description.
Many of our customers are also in the same boat, but as you can see from the video the installation is actually quite straight forward. You should not have any issues if you follow the instructions carefully, but if you do, please know that you can call or e-mail us at any time if you need help. You can reach us at help@precisionled.com!
Is it possible to replace the light bulb in the glove box for a 2013 Camry LE?
If the bulb is a halogen, then yes it is possible. However, if it is a factory LED, this bulb would be soldered to a chip and board, and you would not be able to swap it out.
Your video convinced me to buy one yesterday. Thanks!
Thank you for choosing PrecisionLED! We hope the installation went smoothly!
wait did u have trouble installing it
Would have been a lot more helpful had you shown installation on the driver's side of the car. The passenger side is of course the easy one with a lot more room available to work. Also a close-up demonstration of pushing or squeezing the tab on the power connector would have been very helpful in my opinion. It's not obvious as you make it out to be. Have seen a lot of your videos and the majority of them are very good but for this one small omission about the tab on the power connector this one is another winner thank you.
I have a 14 Toyota Avalon and I'm thinking about upgrading to led but I would really like to see how it's done
Thank you for the interest. We will keep an eye out for an Avalon out here in Los Angeles for an installation video. However, please note, the installation process is very similar for all vehicles. I would recommend having a watch of some of our other DIY videos, and you should gain a general knowledge of how LEDs are installed.
+PrecisionLED Thanks
I know your bulbs are 3200lm/LED, however other premium lights offering 2400lm/LED bulb. On the video and photo those 2400lm look really bright and 3200 should be even brighter. I am afraid that 3200lm are going to be too bright. Would you agree or disagree? Thanks
Absolutely not. If you are concerned about glare projecting into oncoming drivers, there are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers.
It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID/LED lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K lights on the road because they are more natural to the human eye. For this reason, we only carry the 6000K color temperature for our headlights.
Have you had any issues with flickering?
Does this void your warranty with Toyota? I have a leased camry and I want to know if they'll create any problems if I install this in my leased 16 camry.
No, upgrading your lighting will not void your vehicles warranty, as it is protected by the Magnuson-Moss Act. I have linked some information on this law below for your convenience.
www.impalaclub.com/naisso/magmoss.htm
Thanks man you the best just install LED throughout my 2015 Camry, looks great :)
Thanks for the feedback!
I just purchased Quantum Series H11 CREE LED Package
H11CREEHLLED. Is this the 6000k or the 8000k? Can you send me the best one please?
I just ordered some for my 2013 Camry , I hope they last and are bright!
Glad to hear! We hope the install goes smoothly! At Precision LED, we proudly stand by our products, which is why we offer a limited lifetime warranty on all our LED bulbs. Please let us know if you have any issues or concerns!
Hey any updates?
Great video showing the installation!
I installed some LED headlights on my 2015 Camry, but I have an issue where my high beam lights flicker when acting as daytime running lights. I believe it's caused by the decreased voltage being sent to the bulb during DRL use. I purchased anti-flicker decoder modules and wired it up between the power supply and the LED driver, but it just made it worse and caused the light to not work at all. I need some help here cause I just don't know what to do. The lights I got are the Hikari 2023 Future Titanova, and they're flippin awesome when they work right. Did I just choose bad lights?
my friend has a 2016 camry would it also fit that year to?
Thank you for the interest. Yes, the package referenced in the description, as well as the installation video is indeed compatible with the 2016 Camry, as it is still the same 5th generation.
would have to see a before and after for the halogen vs LED lights though
Does the bulb position while in the projector make a difference? I have the passenger side bulb facing up and the driver side is facing down. Do I need to adjust it?
Thank you for your interest. You should always have both of the bulbs installed in the same direction to ensure the light patterns match.
Nice, can you give me the brand or model of this LED Lights? Thanx
Hi Luis! Here is the link to the headlights installed in this video:
Premium H11 CREE LED Kit: bit.ly/2PcnMXK
When I do this install, will it affect my highbeams? Or how will my high beam look like? I currently have factory halogens only. On my 2015 camry XSE. Looking to purchase this.. and are these the same as the xenon brand led headlights?
We do have listed that your low and high beams project light from different lights. No, the headlight kit will not affect your highs at all. The high beams will remain halogen. Also, no, Xenon is a gas that is inside of HID bulbs. We only sell Premium Canbus LEDs.
I have a 2015 Mitsubishi Outlander Sport ES & I want to install led bulbs in it. Do you have a instructional video for my model of car?
It has the dust/rain cap over each bulb housing. Thr cap has a wire through it already, but where will all the extra wire go & the led driver? Thank you :-)
LED headlights can cause a lot of glare on certain reflector housings. Do these work as designed by the Toyota on a Camry 2017 without all that blinding glare and/or uneven lighting patterns? Please explain.
There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K or 8000K lights on the road because they are more natural to the human eye.
Krishna Das Are these white led or blue?
We only sell LED headlamps in the 6000K Crystal White color.
PrecisionLED Sorry I am a noob for headlight bulbs did some research I know that now lol
Does it blind oncoming traffic like custom xenon conversions in regular halogen headlights?
There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K lights on the road because they are more natural to the human eye.
i’ve got a 2007 xle and recently bought new led bulbs for it, will i need a converter thingie or will it be just fine.. i’m sorry i don’t know much of anything about cars..
Hi, if you purchased one of our headlight kits you will not need anything extra as our kits come with built-in resistors to make the installation a very simple, plug-and-play process! If you need any help with installation please feel free to reach out to us at help@precisionled.com.
What kind of the projector lens that you used for this car ?
It is the stock Camry headlight lens!
Typically on average, how long do the LED lamp last?
Thank you for your interest. Our LED headlamps typically last years, depending on use/battery efficiency. However, we do back all of our products with a 1 year warranty.
@@PrecisionLED 1 year or is it now lifetime?
My 2011 came se has stock headlight lens and bulbs. Haven't done anything. So I can just purchase this kit and get right to it? Course I plan to refinish the lens. But u mentioned projection lens...
Yes, as long as you have not changed your headlight lens to an aftermarket one, our kit will indeed work for your vehicle. Our kits are designed for your stock halogen lens.
Can I take stock 2012 toyota Camry se headlights and replace the bulbs with these LEDs?
Yes, it would indeed be compatible with your 2012 Camry!
i will purchased very soon but i want the led lights also for the bottom lights in the front bumper also..its Orange doesnt look well with the leds headlights...do u have a video for that? or the led product
PlatanoRico86 I hate how it looks too. Too much damn orange
These come with the balist if you buy from your description correct? On the website it only says includes headlights
Yes, that is correct, the product linked in the description comes with 2 LED bulbs, 2 LED ballasts, and 3M mounting pads to mount the ballasts.
can you tell me what led head lights to get from precision that will work with high beam and low beam for a 2009 Toyota Camry Le
You can find the compatible high beam kit here: www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html
And the low beam kit here: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
i just ordered mine i hope they come in quick. By the way how long does it come take to come if i put in 3-5 business day option
Hi, thank you for your purchase! We usually ship out our orders on the same day if it is a business day during business hours, but if an order is placed on the weekend or after business hours we will probably ship out on Monday.
Do we need to replace headlights assembly? Or just H11 headlights? Also factory Headlights 9500 are still there right ?
Great video and I followed your instructions and got mine done! Fresh looking. Now do you have DRL/Highbeam for 2017 camrys?
Yes, we absolutely do. We have listed your highs/DRLs would use the 9005 bulb fitment, and you can find a direct link to the product here: www.precisionled.com/premium-9005-cree-led-headlights.html
@@PrecisionLEDdoes the daytime running light flickers?
does the led effect the daytime running lights that come on automatically ?
Yes, certain model LEDs (cheaper brands, typically) are not compatible with the DRL system, and will disable this. Our LED kits will not affect the DRL.
Is the light you recommend here from your website one of those super bright lights that look blue white, or is it the sot yellowy white light?
We offer two color temperatures, 6000k crystal white and 8000k cool white! Neither color is yellow but the 8000k has a very subtle hint of blue.
What will this and your other video for the 5th gen Camry not change? I'm trying to go with all led lights
I believe the only thing missing would be turn signal and brake lights, as we do not recommend replacing these lights. Reason being is because the electrical system will cause these LEDs to hyper flash. However, you will experience no issues with what is shown installed in our DIY videos.
Do you have to adjust the headlights to have the right cut off line?
No, you do not typically have to adjust the cutoff line after installation. However, I would double check to ensure it is not shining too high or low regardless.
Do you have a video of 2013 - 16 Elantra GT H7 LED ? I installed your Interior LED package on my Elantra GT , looks awesome ! Much better lighting than stock .
Thank you for your interest. Unfortunately, no, we do not have a video for the 2013 - 16 Elantra Headlamps. However, the installation would be nearly identical to as shown in this video. The only major difference would be physically locating your halogen bulb.
Hi Phil. Can you make a video on how to install led headlights for 2011 toyota corolla s and 2018 hyundai santa fe sport. Thank you and more power to you guys. 👍🏼👍🏼
We will keep an eye out for a 2011 Corolla and 2018 Santa Fe Sport to film out here in Los Angeles. Thanks for the support!
Can you make a video on how to change the signal lights that's below the lights
We do not advertise the turn signal upgrade because it will hyper flash when ignited. We are currently searching for a solution for this so stay tuned!
Hey! I just bought the LEDs installed them in my car and hear a weird whirring noise that is kind of noticeable from inside the cabin/interior. Is this normal? I am afraid that it can cause a short or has something to do with the voltage
Yes, it is entirely normal for there to be a slight hum from the ballast or the heatsink that is connected to the backend of the LED bulb.
Any update? I would like to know if you had a good overall experience with these lights. Also, is the noise really annoying?
How is the noise or the hum now?
@@jeffj318 don’t have the car anymore bro
@@junglejuice23 the humming is normal
Product Link not working, where do i purchase? dont know which one to buy on your website.
I do apologize for the confusion, but the CREE H11 product is currently on backorder for week, so the product has been disabled. However, I would recommend checking back in a week or so, and it should be back up. We thank you for your patience.
Will these LED’s cause turn signal hyper flash on my 2012 Camry SE?
No, installing our LED headlights will not cause the turn signal to hyper flash. Only installing LEDs on the turn signal would cause this reaction.
Do you have video for the 2011+ Sienna ? I want to know how the light output look like
Unfortunately, we do not have an install video for your vehicle just yet, as we have not yet gotten our hands on one out here in Los Angeles, CA. However, the installation process is virtually the same for all vehicles. I would recommend having a watch on some of our other DIY videos, and you will gain a general knowledge of how LEDs are installed. I have linked our How-to Page below for your convenience.
Also, the LED headlamps will increase your nighttime driving visibility by 2-3x.
www.precisionled.com/how-to-videos.html
Which is best LED or HID? I'll hang up & listen(radio talk)
Thank you for your interest. Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than LEDs.
I have linked some additional information below for your convenience.
www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
THE LINK FOR THE PRODUCT IS NOT WORKING IF YOU CAN GIVE US THE PROPER LINK, WOULD LIKE TO PURCHASE IT FOR MY 2015 CAMRY ASAP
I JUST BOUGHT THE CAR ON FRIDAY, EVERYTHING IS PERFECT EXCEPT THE LIGHTS. HOPEFULLY WE CAN GET INFO SOON
I apologize for the inconvenience, but we currently have the CREE H11 Headlight product (item in the description) on backorder. The product has been removed from the website for a short moment. I would recommend checking back in a week to see if it is back up, as this is the timeframe we do expect to receive a replenishment of inventory.
We thank you for your patience.
I apologize for the inconvenience, but we currently have the CREE H11 Headlight product (item in the description) on backorder. The product has been removed from the website for a short moment. I would recommend checking back in a week to see if it is back up, as this is the timeframe we do expect to receive a replenishment of inventory.
We thank you for your patience.
Hello! How can i buy this led light? On the website there is not this product.
Thank you for your interest. You can find the exactly product used in the video here: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
can you please do vedio about led light for headlights 2016 toyota ravxle
Thank you for your interest. We do indeed have a headlight installation video for a Rav4, which you can find here: www.precisionled.com/how-to-videos/toyota/toyota-rav4-headlight-2005-2013.html
hi, i don´t see on your web site my type car Toyota Avensis T27, year 2011. Are you have led bulbs for it?
Our database is based off of US manufactured vehicles. It is possible that we have a headlight kit for your vehicle, however, we do not have the bulb fitment listed in our database. If you can tell us the fitment, I can see if we carry a compatible kit. You can get this information by simply reading through your Owner's Manual.
does the light bulb should be up side or facing down
Just line up the tabs and twist to lock into place!
I heard some of the conversion led leaves dark spots?- does it have same issues?
What you are referring to are grounding shadows, and are caused by the return wire that elevates just slightly above HID or LED bulbs. However, our LEDs do not come with this return wire, so you will not experience any grounding shadows, or dark spots.
how much do those bulbs cost?
Please check the description box! The links should take you to our website for pricing details.
are you guys going to do a future video on how to install a led switchback for turn signals for 2015 toyota camry se?
Thank you for your interest. We are always on the looking for vehicles to shoot new or updated videos. We will keep an eye out for a 2015 Camry for your requested video. Subscribe for updates!
Thank you for your interest. We are always on the looking for vehicles to shoot new or updated videos. We will keep an eye out for a 2015 Camry for your requested video. Subscribe for updates!
Hows the output on this one?
I think you changed the low beams. What about high beams?
For the high beams, you would have to install a completely separate LED kit, which you can find here: www.precisionled.com/premium-9005-cree-led-headlights.html
my projector reflctor paint have some burned inside it and Halogen bulb so dim will led help without change the headlight it self
I am not sure I understand. Installation of our LEDs will upgrade your nighttime driving visibility from your halogen bulbs by 2-3x.
What do you recommend for a 07 Camry in a rural area need all the light we can get since it's so dark on roads thx
Thank you for your interest. I have linked the compatible kits for the headlamps, as well as the high beams below for your convenience. Both of the packages will increase your nighttime driving visibility by 2-x times.
Low beam:
www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
High beam:
www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html
Will this work on the 2011 Camry? The 2011 Camry doesn't look like the 2012 or 2015 Camry.
Also, originally my car had like regular headlights on the LE model is there something I would have to do to not blind people within the housing?
Thank you for your interest. Yes, the installation would be virtually identical as shown in the video, as your vehicle would use the same H11 bulb type used.
No, our kits are designed for your stock headlamps. There are many factors and many upgrades to headlight housings over the years that help mitigate any glare to oncoming drivers. It is more or less the color of the light which causes distraction and not the actual brightness intensity itself. If you notice, the most distracting lights to see on the road are the blue HID lights which cause a lot of glare for the human eye, whereas you probably never noticed the 6000K or 8000K lights on the road because they are more natural to the human eye.
will it work for a 2011 Camry LE?
Yes! This kit is compatible with your 2011 Camry LE!
what do you do when de headlight use the system of dust covers (headlights in the back have a platic cap like the headlights of a Ford FUSION 2015) ?
Thank you for your interest. First, you would have to ensure that there is enough room for the LED to fit into the housing with the dust cover sealed. I would say you would need an additional inch of space vs your halogen bulb into the housing. And if the LED does fit, then you would have to drill a small hole in the dust cover in order to feed the bulb wires through. Lastly, it would be important to seal the hole with tape.
Was this the high beam or low beam head light
This installation was for the low beam. However, the high beam is virtually identical, but you would install this kit: www.precisionled.com/premium-9005-cree-led-headlights.html
Are these compatible with the Camry Hybrid 16 XLE?
Yes, the installation process is virtually identical to as shown in the video. The only difference, if any, would be physically locating your halogen bulb.
Thanks for your video is it work for 2010 Toyota Camry
Yes, the installation process should be very similar, if not identical for the 2010 Camry.
@@PrecisionLED Thank you
Do these lights flicker in daytime?
No, LEDs are indeed designed to dim, so when your lights are in DRL mode, they will just dim and NOT flicker.
I looked online and I couldn't find the led kit for my 2015 camry?
Thank you for your interest. I do apologize for the confusion. You can find the headlamp LED product compatible with your 2015 Camry here: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
+PrecisionLED thank you for your help and the link can't wait to see my camry look good.
Will this work for the new 2018 Toyota C-HR?
The installation process would be similar but you would install this kit:
www.precisionled.com/premium-9012-cree-led-headlights.html
do you need to install a cancellors or capacitors?
No, that would not be necessary for the Camry. The package listed in the description comes with everything you will need to successfully upgrade your headlamps to LED.
Thank you!
Is this the same as a xenon light in terms of coverage? can you do a test on the road
Depending on the product you are installation, yes, the idea of a LED and HID installation are virtually identical.
I'm sold. This seems much easier to install for me. How much do these cost when on sale?
You can find the direct product link in the description. The kit goes for 139.99.
Thanks, purchased on Sunday; should be here Friday. Thanks for the quick shipment, can't wait to install these ;)
What size bulbs do I need for a 2012 Camry se some people say 9005 and some say h11
uses both, for low beam H11 and for the high beam 9005
That's correct we used the H11 in this video, which you can find here: bit.ly/2PcnMXK
do you any led kights for the bottom turning signals for a 16 camry
We actually do not advertise turn signal LEDs as they would hyper flash when ignited.
Which is better hid or led?
Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than LEDs.
I have linked some additional information below for your convenience.
www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
You got video to intall led light for the fogs?
Thank you for your interest. No, we do not have a installation video for the fogs. However, the installation process should be identical to as shown in the headlight video. The only major difference would be accessing your fog bulb.
Would you have a pair that can go into the 2010 Camry?
Thank you for your interest. Actually, the product link in the description of the video is compatible with your 2010 Camry as well, as they would both use the same H11 bulb type.
+PrecisionLED have you had any complaints from customers for getting pulled over, as the LEDs are bright similar to HIDs? Or is that mitigated due to the projector housing? I ask because my 16 CRV only has the reflected housing.
Got an Aussie 2012 Camry......h7 bulbs....lock ring won’t fit behind bulb
It sounds as though your H7 bulbs may require an adaptor in order to lock your lights into place. Feel free to reach out and contact us directly at help@precisionled.com. We're happy to help!
are these brighter and better than the HID's?
Both LEDs and HIDs do indeed have their own perks. Either can be brighter, depending on the quality of product purchased. We believe we have some of the highest quality products on the market today, which we back with a warranty. Also, LEDs are known to last slightly longer than HIDs.
I have linked some additional information below for your convenience.
Please, do not hesitate to contact us if you have any additional questions or concerns.
Sincerely,
Brent @ PLED
www.caradvice.com.au/278125/headlights-explained-halogen-v-hid-v-led-v-laser/
Will this fit into 2012 Camry?
Yes! The installation process for the 2012 Camry is virtually identical to as shown in the video. Hope it works out!
Do you guys ship this product to Canada?
Yes, we ship all around the world, including Canada!
Do you guys have any h11 led for 2011 bmw 528i?
I believe the 2011 BMW 529i comes with stock HIDs for the low beams, which you cannot swap as the ballasts, connections, and bulbs are completely different fitments than our LEDs. Our LEDs are designed for halogen upgrades to LED.
How do these do in the snow?
All of our LEDs are weather and waterproof, so the snow will not affect the performance or lifespan of the bulbs.
I noticed I don't get good light out put with led lights. kinda dissatisfied with the led.
This would definitely depend on the quality of LED headlamps you are installing on your vehicle. If you install a poor quality product, then you will indeed experience poor quality light output from your headlights. However, we believe we have some of the highest quality LED products on the market today, which we back with a 1 year warranty. I would expect the LED system installed to increase your nighttime driving visibility by 2-3x.
If you are unsatisfied with your purchase, we do indeed have a 30 day, no hassle return policy.
Do you guys still have these in stock?
Yes, we do indeed carry this kit, however, it is currently on backorder. We do expect a replenishment of inventory to come in within a week. The product linked in the description should be enabled back onto the website in just a couple days.
Would aftermarket LED headlight trio codes, and cause damage to my car's electrical system? I have read info that I could due to modern car's electrical "canbus" system? Thanks.
No, we only sell high quality Canbus products to ensure you do not experience any dash errors, flickering, electrical issues, or any other issues with the LEDs.
Do you have a kit for 2015 RAV4?
Thank you for your interest. Yes, we do have a headlight kit for your 2015 Rav4, which you can find here: www.precisionled.com/premium-9005-cree-hl-gl-headlight-led.html
Are these the H11 CREE LEDs??
Thank you for the interest. Yes, that is correct, the LEDs are indeed the H11 cree LED kit, which you can find here: bit.ly/2PcnMXK
Thanks, really helpful.
Thank you for watching!
What about the 9005 daytime/high beam lights ?
The installation process for the DRLs / high beam would be identical to as shown in the video. The high beam socket is right next to the low beam socket. You would install this kit: www.precisionled.com/premium-9005-cree-led-headlights.html
@@PrecisionLED thank u 🙌🏻
where do i buy the kit
Hey! The product is linked in the description, but here's a direct link to it! bit.ly/2PcnMXK
does a 2013 Camry use the h11?
Yes, we do have listed the 2013 does indeed use the H11 bulb for the low beams.
okay thanks sorry didn't the the description at first
Very Nice
You have good thorough videos, but you should change the title. The current generation Camry is 2012 and up, 2007 to 2011 are the previous generation.
We appreciate the feedback. We will look into this, and if it is correct info, we will definitely change the title.
PrecisionLED still hasn't changed the title and successfully wasting people's time SMH
@@PrecisionLED I want to order but am a little confused. I have a 2grfe 2011 camry se that I thought was a generation 6. I believe camry had a 'facelift" 2011 model but not sure if this was considered Gen 6 or 7. Either way mine is 2011 Gen 6 SE v6 Camry .. Will these work on my car ? =) www.precisionled.com/premium-h11-cree-led-headlights.html?
@@jahmosaxenamp6797 Thank you for your interest. Yes, that is indeed the correct kit for your 2011 Camry SE, as your vehicle uses the same H11 bulb fitment for the headlamps as the previous years.
will this work on my 2009 camry?
or do i need a conversion kit?
Thank you for your interest. The installation process is virtually identical to as shown in the video, and you would install this kit: www.precisionled.com/premium-h11-cree-hl-gl-headlight-led.html
my lights have just arrived but im struggling to put it in
How can we assist you? Please feel free to reach out at help@precisionled.com with any installations questions you may have!
@@PrecisionLED hi thank u for reaching out. i actually put it in. i just couldnt try ig at night besides i really love the quality
Great, glad to hear that! Thank you for choosing PrecisionLED!
Is this legal and how many k?
The legality varies vastly from locale to locale. You would have to check with your local laws and regulations. What is illegal in most places are the color hues, as they could project glare to oncoming drivers. As opposed to the 6000K color temperature, which is right around the color of stock LEDs. This would project a pure white and is more natural to the human eye. This is the reason why we only ship the 6000K color temperature with our headlamp kits.
will it work with avalon 2016 ?
If you have halogen lights and not HIDs you would install this kit:
www.precisionled.com/premium-9005-cree-led-headlights.html
What is the lumen output?
Our headlight LEDs are rated at 3200lm/LED bulb, which would be a total of 6400lm.
Is it work for 2007 ?
Yes, the headlights linked in the description box are indeed compatible with the 2007 Camry!
What's the price on these
Our CREE Headlight Product is listed for 139.99 USD. There is a direct product link in the description of the video.
thanks...
can u show it on CAMRY 2014 model
Thank you for your interest. The installation process would be identical to as shown in the video. The video applies to all years 2011+. You can find a direct product link in the description.
I have 2014 camry it does not look anything like that. I have bought an LED headlight but it wont fit everyone says you need special retainers
Awesome video.
Thanks for the support!
Good video
Thank you!
Hi, are you at San Gabriel area.
Yes, we are located in the Los Angeles area.
i want one but i m literally so nervous coz i have never done this before
Many of our customers are also in the same boat, but as you can see from the video the installation is actually quite straight forward. You should not have any issues if you follow the instructions carefully, but if you do, please know that you can call or e-mail us at any time if you need help. You can reach us at help@precisionled.com!
thank you for the reply
👍