Tip: Apply a thin layer of grease on the sealing surface of the crank case before you put the gasket on. This not only holds the gasket in place while you put the other case half on, it also makes it easier to remove the gasket next time you split the case.
Sick vid, I too ride a YZ125 and I have a 2019 model. I recently weeded it over a sand jump at a track and now I need to get a new helmet as I have cracked mine and a few parts🥴😂😂
Did you polish that clutch cover? If so how? Mine is worn from years of boots scratching it, have thought of replacing aftermarket but high cost just to look a little cooler
Hello, I have a question on gaskets. I noticed that no sealant was required when you reinstalled. When is a sealant required? I am replacing the cover on my grandson’s 2005 Yamaha PW50. Should I use any type of gasket sealant?
You only need to use sealant if there isn’t some sort of gasket in place, but pretty much everything uses gaskets on dirtbikes. The only time a sealant is used is between the cases, and even then some bikes use gaskets. Hope this helps 👍🏼
I tried installing a 12T front sprocket. The inner diameter groove of the sprocket is smaller on the 12T compared to the 13T OEM sprocket. The 12T doesn't sit on the counter shaft like OEM. Have you ever run into this issue?
@@bbob5050 You got to admit, his estimation on each bolt is fairly similar to spec. I honestly have no doubt that it’ll run just fine and last as long.
Where did you get your reed valve gasket?? I can’t find them anywhere, I have vforce 3 reeds and when I recently rebuilt my motor the hot rods bottom end rebuild kit didn’t have one so I had to use gasket maker and I think I developed a air leak so I need to replace it with a gasket but I can’t find one!
OEM they don't come with gaskets, many aftermarket Reed Cages do though. I found mine on Motosport but you could always directly contact V-force about getting a gasket
@@akmoto_ are you only into dirt bikes or street bikes ? I just got back into bikes and picked up a f4i would be awesome if you did a built on a f4i I'm thinking about picking up a yz250 now
Hello my friend! Segment cut game, squish, compression ratio.... no? Why? Maybe it is the shop...always warning With segment cut game even With new segment... it’ s frequently is not good.... sorry for my English.... good job bro!! The French Guy 🤙
🙏Hi bro I am sahil from India nashik Maharashtra state bro I want Yamaha yz125 two stroke dirt bike in prise of 500 dollars so plz find the dirt bike ❤️🙏👍
I want to get Yamaha YZ 125 its great dirt bike not to small not huge heavy bike. Plenty of power and dependable.
Tip: Apply a thin layer of grease on the sealing surface of the crank case before you put the gasket on. This not only holds the gasket in place while you put the other case half on, it also makes it easier to remove the gasket next time you split the case.
Kevin Jooste yep that’s what I did for my 250f
Semoga saya bisa memiliki nya suatu saat, yz 125 i love it
Love this build and love the long vids!
THANK YOU BROOOO
"little bit of oil and lube up the shaft before installation" said every man ever
Супер! Молодец!
Noice video !👌🏻
Do you have a video for the bottom end Installation of the components?
Sick vid, I too ride a YZ125 and I have a 2019 model. I recently weeded it over a sand jump at a track and now I need to get a new helmet as I have cracked mine and a few parts🥴😂😂
Nice vid bro
EAAAAA AGUANTE LO NOTA
Very informative and professional it's not your first rodeo is it I really enjoyed your video bud
Y la varilla del embrague, y el armado del encendido?
Good build man that engine could use a vapor blast would look better
damn good videos! Tanx
Did you polish that clutch cover? If so how? Mine is worn from years of boots scratching it, have thought of replacing aftermarket but high cost just to look a little cooler
Creo que se olvido ajustar el perno del engranaje pequeño que va puesto en el cigueñal, el que transmite fuerza
No quité el perno, así que no es necesario apretarlo
@@akmoto_ ahhhh es que lo note en el minuto 2:30
Do Lc135 engine assembly
Nice one 👍canyou tel me how much cm is the wood for the engine krate i like to make the same you have 😃
The one in the video is 4 12 inch 2x6s bolted together. I recently made one out of 4 11 inch 2x4s and seems to fit smaller engines better
@@akmoto_ thank you for telling this thanks 👍👍👍👍😃😃😃😃
Hello, I have a question on gaskets. I noticed that no sealant was required when you reinstalled. When is a sealant required? I am replacing the cover on my grandson’s 2005 Yamaha PW50. Should I use any type of gasket sealant?
You only need to use sealant if there isn’t some sort of gasket in place, but pretty much everything uses gaskets on dirtbikes. The only time a sealant is used is between the cases, and even then some bikes use gaskets. Hope this helps 👍🏼
I feel dumb asking this question but this rebuild Apply’s exactly the same to the 250 as well right ?
What year was this yz 125
Are you gonna make it out to WKR on the 22nd
👍👍👍👍👍
Why did you give some torque settings but , when it came to the top end you didn't say any torque settings 😣
It’s always best to refer to your service manual, torque specs can be differ from bike to bike! 👍🏼
Yeah I meant for the yz125 not different bikes
What is year of this yamaha?
o nice very nice amazing good...and plz work to suzuki engines
I tried installing a 12T front sprocket. The inner diameter groove of the sprocket is smaller on the 12T compared to the 13T OEM sprocket. The 12T doesn't sit on the counter shaft like OEM. Have you ever run into this issue?
No, I would try maybe a different brand of sprocket.
Great build tho mate but torque specs would be nice 👍
He doesn’t know them cause he didn’t torque anything down but the clutch nut 😂
@@bbob5050 You got to admit, his estimation on each bolt is fairly similar to spec. I honestly have no doubt that it’ll run just fine and last as long.
Can you rebuild my 06 yz125?
What that adapter called that you used to tighten down the cylinder nuts
It is a motion pro torque wrench adapter
Where did you get your reed valve gasket?? I can’t find them anywhere, I have vforce 3 reeds and when I recently rebuilt my motor the hot rods bottom end rebuild kit didn’t have one so I had to use gasket maker and I think I developed a air leak so I need to replace it with a gasket but I can’t find one!
Try revzilla
OEM they don't come with gaskets, many aftermarket Reed Cages do though. I found mine on Motosport but you could always directly contact V-force about getting a gasket
Thanks! I got one ordered up. Amazing video too keep doing what your doing🤙👍
@@akmoto_ are you only into dirt bikes or street bikes ? I just got back into bikes and picked up a f4i would be awesome if you did a built on a f4i
I'm thinking about picking up a yz250 now
I definitely have more knowledge about Dirtbikes than street bikes
What year bike is this?
2018
What year is this engine?
2018
Sir, if I want to take the used engine of yz125 2006 then how much will I get?
Hello my friend! Segment cut game, squish, compression ratio.... no? Why? Maybe it is the shop...always warning With segment cut game even With new segment... it’ s frequently is not good.... sorry for my English.... good job bro!! The French Guy 🤙
What gear oil do u put in, I got a 2015
I use Maxima MTL, Yamalube all purpose 10w-4 is a cheaper option also
What kind of video equipment are you using to film? Great video and I like the entirety of your page, it’s clean and blue! 🤤
Pgn punya yz 125
No offense or anything, but you should cut your nails... atleast theyre clean tho haha but overall its a good video, keep it up!
Bro his nails aren’t even long
I KNOW RIGHT
What if he finger picks guitars when he’s not rebuilding engines
@@donalddonaldson7211 oh maybe hahaha
Yamaha engine s always different from other companies....
🤙👍👍
I am Italian, your work and preparation of tools and materials and beautiful, good beautiful work
🙏Hi bro I am sahil from India nashik Maharashtra state bro I want Yamaha yz125 two stroke dirt bike in prise of 500 dollars so plz find the dirt bike ❤️🙏👍
nyari kawan bang,,,,
Now if he can keep his nails clean how come the rest of you men struggle😭😭😭
I like to get dirty with my toys