So how did you get bolsters to work if you just spliced both bolster wires together? When initially you had no power for the bolster wires? You need to jump power from Pin 4 or not. Cause that’s what all the forums say
I put 330i sport seats in my 09 e91, pass side bolster works with out modification, drivers has nothing, no relay clock or pump motor. Swapped switch to pass side and confirmed good.
Trying to do this on this on my f30, since my original seats didnt come with lumber and bolster support but the new one has that option😭 cant figure out wat wires to splice
Get a multimeter, disconnect harness, turn on ignition and check each pin of the connector coming out from the floor. You should see 12v on the pins you need.
Hey Cameron, thanks for the video. I'm in this process. What I don't understand is why would you connect pins 7 and 9 together if there is no power coming from the car to neither of these pins? Since the car had no sport seats. My LCI car had no heated seats and I'm swapping the non-LCI sport seats into them. I don't know which wire I should tap the "steady plus" from with a splice. Am I correct? Kind regards
Hey man great video ! I just swapped in e90 sport seats into my e46. Passenger side works fine except for the seat belt airbag light. Driver side has 2 power and 2 grounds connected those up moved seat into position. I went inside to grab a snack came back outside and the driver seat will not move anymore. Before that the seat would not tilt forward. Any ideas ?
Hi, I have change normal seats without heating, with a sport seats which have lumbar and bolster. Is possible to do the same wiring like you do to connect everything?
This is possible. There are universal heating pads available for most seats. They are usually secured with a 10 amp fuse (per seat) the difficult part is disassembling your seat to place it under the upholstery. If never done before it's possible but it takes some patience.
Bolsters fully open are still fairly tight, and still much better than standard seats. I'd be happy if I had sport seats with unadjustable bolsters. Mine don't have lumbar, and they're plenty comfortable, so I'd imagine you could go without that adjustment too. That said, getting the wiring sorted isn't very difficult once you wade though all the mixed information.
So how did you get bolsters to work if you just spliced both bolster wires together? When initially you had no power for the bolster wires? You need to jump power from Pin 4 or not. Cause that’s what all the forums say
Don’t worry about what pins just connect the two red wires, one big one small. Did the trick for me.
what about the brown ones? i have '10 lci e92 and ive put into it pre-lci sport seats
Comments are more valuable than the video itself
So any clearer instructions? The forums do not say to connect pins 7&9 together. Lmfao it says connect 4 to 9, 8 to 13
I need to do this on my e87, didint get the wiring part, could you detail the steps to do it? Thanks
Yes please!! 🙏🏼
I put 330i sport seats in my 09 e91, pass side bolster works with out modification, drivers has nothing, no relay clock or pump motor. Swapped switch to pass side and confirmed good.
Trying to do this on this on my f30, since my original seats didnt come with lumber and bolster support but the new one has that option😭 cant figure out wat wires to splice
😅 me to. did you find the solution?
Get a multimeter, disconnect harness, turn on ignition and check each pin of the connector coming out from the floor. You should see 12v on the pins you need.
Disconnect harness, turn ignition on and say hello to airbag fault 😁
Hey Cameron, thanks for the video. I'm in this process. What I don't understand is why would you connect pins 7 and 9 together if there is no power coming from the car to neither of these pins? Since the car had no sport seats.
My LCI car had no heated seats and I'm swapping the non-LCI sport seats into them. I don't know which wire I should tap the "steady plus" from with a splice. Am I correct?
Kind regards
Hey man great video ! I just swapped in e90 sport seats into my e46. Passenger side works fine except for the seat belt airbag light.
Driver side has 2 power and 2 grounds connected those up moved seat into position. I went inside to grab a snack came back outside and the driver seat will not move anymore. Before that the seat would not tilt forward. Any ideas ?
Did you solved ?
@ no never solved. Seat stayed in that position and sold the car shortly after. Month after kid crashed and totaled it.
Hi, I have change normal seats without heating, with a sport seats which have lumbar and bolster. Is possible to do the same wiring like you do to connect everything?
Connect 7 and 9 together ? :)
Do you know I can add heated seats ? I have sports seats but they are not heated
This is possible. There are universal heating pads available for most seats. They are usually secured with a 10 amp fuse (per seat) the difficult part is disassembling your seat to place it under the upholstery. If never done before it's possible but it takes some patience.
@@Dahley-d7fcan be dangerous doing that with sketchy elements
Can you just upgrade and not worry about adjusting the bolster and lumbar...??
Yeah if you want to be uncomfortable
Bolsters fully open are still fairly tight, and still much better than standard seats. I'd be happy if I had sport seats with unadjustable bolsters. Mine don't have lumbar, and they're plenty comfortable, so I'd imagine you could go without that adjustment too.
That said, getting the wiring sorted isn't very difficult once you wade though all the mixed information.
Boss you didn't explained nothing at all.