Dear.. Your video has been VERY useful to me. I followed the disassembly instructions closely until I reached the paper pick-up sensor. If it was not for this video, I wouldn't have dared to do anything, especially that most of the assembly is fixed with those nasty hooks that you wouldn't know they exist until they're broken!! Sincere thanks to you.
Thank you for this video, helped me in disassembling the control side only to find out somebody had pressed the wifi switch so hard that it had got stuck, released it, now it works perfectly fine
Great job! Please My toner got stack inside the printer and was forcefully removed. I have notice there is a damage metal spring at the leftside of the toner holder inside the printer. Can you help me on how to replace the holder frame please? Thanks in advance.
@@viandant5 printed text is tilted, if i will print straight horizontal line, on one side of the page i will have 2cm from the edge of the page, and the other side i will have 2,5cm. Text looks nice, and the printout looks OK.
hi, the pickup roller motor (is it its job? I am guessing here...) only pulls a sheet of paper half a way in and then stops. When I pull the paper out back from the front -with some resistance- there is no printing on it. Why do you think it does that?
I have the same problem... Like it doesnt know that the paper is picked, so it doesnt print on it, and then it just realize, omg there is a paper inside ...JAM... on halfway through..
@@zokigrujic i mene moj poceo zezati.povuce papir 7 cm.i stane.paperjam. prije toga mi je lose printao po sredini stranice prazno bet tinte pa se mislim da nije do cartrige? da nije prazan. jesi li svog popravio.
@@zokigrujic Your cartridge has little pin feather on left side which is broken. And because of this your catrigde roller door is closed while printer is taking papers. Just buy new one and pay attention not to broken new one during installation or removal. at least this was my case
I took it apart and put it back together, however when push the power button, the spinning makes a large racheting sound, what did I do wrong? It wasn't like that when I took it apart (it keep feeding too many sheets of paper before).
I have a problem with one if the two optosensors. One of them was clogged with the tonner cartbrige and was broken and suffered a missalignment. The printer was working before this situation. Later stop printing. Do you know how to fix the inner optosensor? Because my printer is new... Kind regards
@@viandant5 I mean one of the 2 small wires at the left side cabinet where the toner cartbidge is in. One of them, clogg with the toner, stopping to retire the toner and I pulled stronger, the wire was it burst and was out of position. I tried to reset it but now my printer prints blank ... How I could fix my printer?
This is how a Disassembly and Assembly tutorial should look like. 10/10
Dear..
Your video has been VERY useful to me. I followed the disassembly instructions closely until I reached the paper pick-up sensor. If it was not for this video, I wouldn't have dared to do anything, especially that most of the assembly is fixed with those nasty hooks that you wouldn't know they exist until they're broken!!
Sincere thanks to you.
Just fixed the power button took 5 mins, saved me £100 thanks :D
Thank you for this video, helped me in disassembling the control side only to find out somebody had pressed the wifi switch so hard that it had got stuck, released it, now it works perfectly fine
I have solved the problem, thanks a lot!!! It works and that is a miracole for me, but I have more noise when spin than before...
The noise have disappear after a while. THKS 😋
It really works! Thank you for this sir.
Good vedio❤
Great job! Please My toner got stack inside the printer and was forcefully removed. I have notice there is a damage metal spring at the leftside of the toner holder inside the printer. Can you help me on how to replace the holder frame please?
Thanks in advance.
It could be the spring of the toner contact. In this case you have to remove the side panel and the main board
@@viandant5 Thanks Sir
What a great video! Thank you! Subbed.
Excelente vídeo
Thank you get my printer working again
Excellent work!
Perfect!!! Thks thks.
Lovely video
good job
Lovely resembling
Hi, Very Nice tutorial! I have a problem that my hp1102w is printing crooked text...? any idea how to fix it?? I did update the firmware, and drivers.
WHat do you mean with crooked? Is the text distorted?
@@viandant5 printed text is tilted, if i will print straight horizontal line, on one side of the page i will have 2cm from the edge of the page, and the other side i will have 2,5cm. Text looks nice, and the printout looks OK.
@@waldi4213 It could be the paper feed roller, the separation pad. Try to clean the paper rubber roller along the paper path
Helpfull video
excellent
😍😍😍😍😍😍😍😍
Best video! THX U!
Thanks this very useful
Thanks a lot !!!! Really help foul!!!
very used full. thank you soooo much.
Thanks for sharing
❤❤
Great video but I don't understand why you didn't remove the power supply board , well done I love the video
It's easy so I avoided it. The video is already very long
great video
Thanks
Sir I have promble in Kyocera 2040dn paper jam in tray and in fuser unit what is problem
both tray and fuser unit? try to change paper, clean the separation pad with alcohol, check if the fusers are too worn
Which one is the WiFi adapter .. I want to remove it
The wi-fi card is in the main board
hi, the pickup roller motor (is it its job? I am guessing here...) only pulls a sheet of paper half a way in and then stops. When I pull the paper out back from the front -with some resistance- there is no printing on it. Why do you think it does that?
Could it be a paper jam? Also check the paper settings, are they correct? Where does the sheet stop?
I have the same problem... Like it doesnt know that the paper is picked, so it doesnt print on it, and then it just realize, omg there is a paper inside ...JAM... on halfway through..
@@zokigrujic i mene moj poceo zezati.povuce papir 7 cm.i stane.paperjam. prije toga mi je lose printao po sredini stranice prazno bet tinte pa se mislim da nije do cartrige? da nije prazan. jesi li svog popravio.
@@zokigrujic Your cartridge has little pin feather on left side which is broken. And because of this your catrigde roller door is closed while printer is taking papers. Just buy new one and pay attention not to broken new one during installation or removal. at least this was my case
I took it apart and put it back together, however when push the power button, the spinning makes a large racheting sound, what did I do wrong? It wasn't like that when I took it apart (it keep feeding too many sheets of paper before).
Are you sure you reassemble theprinter correctly?
I have the same problem. Of course I'm not sure about reassemble correctly, I've tried...
very nice
Thank you
Thank you so much!!!
excellent
pls my printer is sheading the whole paper instead of printing normally.. what is wrong, and what should i do? (
Kingsley)
What do you mean with sheading? Check the fusers, HP2015 is an old printer, may be they are worn or defective.
On the inside of left cover there is small black lock which is make me difficult to assemble can you help me please?
Sorry I haven't the machine, I don't know
Thank you sir
I have a problem with one if the two optosensors. One of them was clogged with the tonner cartbrige and was broken and suffered a missalignment. The printer was working before this situation. Later stop printing. Do you know how to fix the inner optosensor? Because my printer is new... Kind regards
What is a optosensor? You mean the laser scanner?
@@viandant5 I mean one of the 2 small wires at the left side cabinet where the toner cartbidge is in. One of them, clogg with the toner, stopping to retire the toner and I pulled stronger, the wire was it burst and was out of position. I tried to reset it but now my printer prints blank ... How I could fix my printer?
@@jorgeruiz5963 That wire is a contact between the cartridge and the printer. You have to reinstall it disassembling the printer, this is the only way
how do I know if the pickup roller motor aligns correctly?
Do you have a paper jam or a misalignment on the printed sheet? A paper jam could be caused by a not working motor
Does this model have a rotary encoder?
What do you mean? Why a rotary encoder?
thanks.
Thanks a lot sir
My printer switch does not work when i close the cover
What do you mean? which cover?
You know its hard to disassemble when you have to look up a tutorial on how to do it
این کارو بچم یادداره تعمیر بزار
Thx
Résoudre le problème d'échec d'installation de l'imprimante HP LaserJet P1102
tahmilatscanner.com/fix-hp-laserjet-p1102-printer-installation-failed/
Helful
very used full. thank you so much.