Milwaukee M12 SURGE vs. Milwaukee M18 SURGE Lag Bolt Face Off
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- #milwaukeem12surge #m12surgevsm18surge
M12 Surge shrsl.com/1p6x7
M18 Surge shrsl.com/1peri
M12 GEN2 Kit homedepot.sjv....
Tool Boss T-Shirts toolboss44.net/ - บันเทิง
It takes a BOSS to wear 2 different socks! Great comparison
🙏🙏🙏🙏🙏😉👍
I respect those in the socks game. Not too many people know but, it's real and, I salute this man.
I just bought the m12 impact driver and drill. I’m just a DIY homeowner, but It’s handled everything I’ve thrown at it. Just installed a cedar board on board fence using screws on the pickets. Just installed a shelf near the ceiling of the garage. Ran a 3 inch lag bolt with no pilot hole and didn’t slow down. No problems drilling into brick. No regrets on going 12V fuel line. I like the light weight and compact size.
I do commercial and residential hvac work, new construction and remodeling/finish..when i first got into the trade i went 18v but always saw.my.foremans using 12v.. the 12v fuelineup handles 90% of the work i need and takes a beating but is a beast..the 18v comes out very seldom
The M12 was tested on CP batteries. XC batteries will have made these two a pure draw.
M18 will give better runtimes though
If not a draw, at least an even closer race. Realistically, no one would use the smaller battery if they had to drive a lag bolt.
My m18 surge seem to over heat way too fast
Power is not there…super weak
Both seem like great impact drivers.
I picked up the M12 Fuel Gen 2 bundle for $199. I was kicking myself when I saw online deals with an extra free tool like the Gen 1 ratcheting wrench.
🤯🤯🤯😉😉👍👍
Same. But no regrets with the tool.
Always get it online.
Love my Surge. Thinking about getting some of the M12s just because
🤣🤣🤘😉🤟👌🙏
I'm a cabinet installer I just shrunk every tool I own to carry less. Haven't had a problem with the m12. Was using 18 Makita and 20 DeWalt.
Great video. I just picked up an M12 surge yesterday. I’ve been Dewalt for years but I’m
Going to give them a try! Might do a comparison with my dewalts on my channel also. I’m sure the noise difference there is probably huge. Dewalt is loud!
🙏🙏🙏
The m18 for all day, hard work. The M12 for partial day, mobile tool bag stuff
This is mainly due to the battery size and the handle ergonomics. You do NOT want to be using an M12 all day, it gets way hotter and is alot less comfortable, and you will feel it after using it all day. You can feel how bad the m12 dissapates heat vs the m18 on your hands. I promise you
🤟🤟🤟🤟
I can vouch for that I have the m12 it is a beast and surprises most ppl on Job but dose get hot after a wile but with the Xc 6.0 it’s not bad at all lol
Hi tool boss,
I also agree about the milwaukee m12 handle grip, it's very uncomfortable. I do like the Milwaukee m18 surge when working inside.
Ur a smart man lolol. Thanks for watching buddy
Michael C the handle on the M12 is perfectly fine. I think the M12 is better because even people with really big hands can hold it, because the battery the adds on to the handle even with the larger capacity batteries. But that’s just my opinion
I needs and wunts. I have 2 drills that are sitting in my garage brand new and now im wanting the surge. Tools, guns, cars, beer and puss is how i do it.
Like the M12 tools....first in bag & off truck. Easy to use for Electrical, plumbing, & HVAC...... Rarely do I grab my M18 tools; as the M12s have the power!(right He-Man....I have the power!....LOL🤣). Pretty cool that Milwaukee was able to pack a lot of power into the M12 platform w/ the hydraulic Impact...just think of what they come up with next for us all.
Thx for the vid Boss....✌🏼
👌🤘🤘🤘👍👍🙏
I always got compliments from guys I work with when they used my m18 surge, unfortunately it was also stolen along with a bunch of other stuff but I will definitely be getting another. Eventually both of these will be gracing the tool van.
Sorry to hear that Ryan 😞
@@toolboss8410 unfortunately it happens and was a big hit. But to be optimistic, it gave me a chance to upgrade. On the downside, I was hoping one key would eventually help, but hasn't been picked up yet lol.
Hit and miss with these notifications. The m12 is long and narrow and the m18 is short and fat. Definitely thought the m12 would be smaller all over. Liking the power the m12 has. Nice little comparison there.
🤟🤟🤟👍👍😉🙏
The M12 version hits a sweet spot for cabinet installation IMO. With the non high capacity M12 batteries it frees up a lot of space for working inside cabinet boxes, particularly screwing together a drawer box or corner cabinets. I don't have any Milwaukee 12v stuff though, so I'll keep using the M18 Surge until it gives up on me. By then there should be a gen III or IV M12 Surge that produces 1,300ft/lbs and will fit comfortably in your pants pocket.
So does the Gen 2 😉
@@toolboss8410 I agree. My only complaint about the Gen 2 and other conventional impacts using them inside cabinets is how loud they resonate, when you have to climb inside large corner cabinet or similar to screw them together the sound deafening. With the Surge it is still loud but significantly less of a sharp.. "painful" noise.
Agreed..just playing 👊🙏😉
essinem4130 you are aware you can affix the cabinets together from the other open box cabinet and not the corner cabinet.
@@kensfestoolchannel7916not if you hiding your screws
Simple and really affective review. Thank you!
The m12 hung with the 18v big brother better than I would have guessed! Thanks for posting! Do you find the same thing true for other tools, that the 12v fuel stuff is close in performance to the 18v fuel versions?
No usually not close in power at all ..this hydraulic driver and specs are pretty similar 👊👌👍👍
Just bought the Gen 2 set and love it Toolboss ! $ 299.00 in Canada.
Wow .. that's crazy .. you don't Kno how many messages I get on Instagram for the price diffrental vs the USA
@@toolboss8410 our Canadian dollar is 1.3 times the American dollar plus we pay more due to increased duty charges the stores have to pay to get the tools
so $1 American
= $1.30 Canadian .... IT ADDS UP VERY QUICKLY .....
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Heres the biggest difference tho.
AMERICA Minimum Wage is $7.25 per hour
CANADA Minimum wage is $14.25 per hour
The big takeaway is the M12 is the second best impact to get. Best 12v and best compact.
Will you do an endurance test on these impact drivers? Because the time it takes you to go replace the battery will null and void the speed. That way we'll know the real winner. I love your videos by the way.
Thanks buddy much appreciated...
nice job brother keep up the good videos and comparisons, can't wait till' the next home depot live vid. 👍🏽👍🏽👍🏽👌👌🤙🏽🤙🏽🤙🏽🤘🏽🤘🏽🤘🏽
Thank you very much Valerie for kind words, much appreciated 👊👊 👊🙏🙏 🙏
Dude. You weighed them in the grass. I have that exact scale and like any other scale you have to put it on a firm surface or it is wrong.
Thanks for the video bro!
You got it buddy 👊👍🤟
M12 all day for electrical work. Fuck that brick
What one is quieter?
So the 12 is still pretty damn good and a lot smaller
Thanks for this review. I was thinking of getting the m12 surge, but then you mentioned the thinner grip on the m18. Since I have smaller hands I have to take that into serious consideration.
I've seen on other videos that the angle on m12 allows you to push with one hand more easily. What do you think?
👌👌👌😉
I have huge hands and I held the m12 today and felt weird. Gonna get it tho
I own a lot of both M12 and M18 tools and if it does the job, I reach for the M12 version when I can.
Put the 6.0 battery in that m12 and test again bro
Doesn't come with a 6.0 😉😉
Dillen keka a 6.0 on my M12 3/8 stubby made a huge difference
Dude we gotta talk about them socks though!! Good Video though!!
Yo boss A+ for Sox swag 😆
👇👇👇👇👇👇 tho I like more then Yanks 🤘
I agree 💯% that the M18 is the better buy. I bet the M18 has more hydraulic fluid in it , so it wouldn’t heat up as quick as the M12.
But being in the M12 line to I will be purchasing it soon. Might wait for some holiday specials for that it tho. 👍🏼
👍🤘🤘👊
Great comparison! Hail Boss 💪🏻
👍👍👊👊👊😉
M18 ftw
👍👍👍
👍👊🤟😉
have as much torque?? as the gin 3
No gen 3 m18 has more torque.
m12 aint too bad eh
👍👍👌👌👌
nice jobe
Can anyone vouch for the grip size between the two? I have the m12 fuel impact and have always wanted the m18 fuel impact. However, the far grip on the m12 is a little annoying. Is the m18 grip slightly slimmer than the m12? If not, that might be a dealbreaker for me as the m12 grip is annoyingly thick.
Yes it is.. i can vouch for it 👋👋👋
@@toolboss8410 awesome! M18 it is, then!
Just got the m18 surge for 139 with free cp2.0