I just purchased everything from your site, I would also love to purchase the mounting plate were you put the switch and supply chuck. Thanks for the awesome instructional video, professional job well done.
Fantastic video! Very detailed and straight forward. Looking forward to getting my 2022 (which is still on order) and installing this. If I were to use an S-Pod, how would those wires connect? I'm thinking the main power wires would still go to the battery, but the black and purple wire would go to the S-pod? Any tips would be appreciated. Again, great job. Thanks for posting this one!
hey man looking to run a compressor set up on the zr2. Would you recommend going with the dual or do you think the single is adequate for the average offroader.
Hi, I really enjoy this series. I recently purchased a new 2019 ZR2 Bison for a do everything vehicle: daily driver, light off roading, and long trips. Since it's a Bison a lot of the mods you've completed were already done, and I've added a Comeup winch, GMPP front level kit and tie rod sleeves. I think air and new tires/wheels might be it (I also have GoFast camper top on order, but that a ways out). I have a few questions that I hope you can help me with: 1) Tire and wheels: At this point I would just be going to 285/75, not 35", and I am looking at going down to 16" wheel for more sidewall and air volume. The Method Race Wheel 702 is 16x8, 6x120, +30/5.60 ,which is almost exactly the offset of the stock wheels. Would this set up work? Would a 0 offset wheel be better? I'm a bit concerned about the bigger tire hitting the upper control arm, but I don't see anything online about that and it seems that lots of people are running 285/75 on stock wheels. 2) Is there any point in saving money and going with a ARB single compressor? 3) Random little questions. The AEV fairlead comes with those bolts that have a 6mm hex key drive. I find that these are really tough to tighten with any toque and not damage, they seem better suited for a bicycle than a truck! Do you have torque specs for the these bolts? I can't seem to find anything online. Thanks for your help and if Im ever in the Knoxville area I'll be sure to stop by.
Is the blue AND red wire fused together on the stud of that fuse block? I'm just curious as to why the switch doesn't stay lit up if the blue wire is connected to the battery. Nice work!!
@@rockyour4x4 Nice. Why then doesn't the switch light stay on? I noticed in the video it's off until you turn switch on. I was worried if I fuse those two wires together the light will stay on all the time. Thanks! By the way I ordered your Sherman Cap and love it...nice little addition to the project.
id like to get your thoughts on tires its time for me to get a new set for my YJ , i like to drive it to the trails i figure you would know a good tire for duel use.
@@ridered7394 we install hundreds of these. The heat from the compressor filling (4) 40” tires trumps any heat radiating from the engine in the back corner of the engine bay.
@@rockyour4x4 Sent you a message on your contact page on your site. Included my order number. need that bracket made. please get back to me with a price so i can get this project going.
That was an awesome video, and you did a great job installing. Very clean and professional!
Clean install!
Very good install. It shows that you take pride in your work!
Awesome work guys! Our Overland Company is about to make the install today!
Evan Taylor Tag us on Instagram or Facebook when you get it done.
Well done video. Easy to follow all your steps.
Very clean and protected installation; I'm sure the customer will be very pleased! :)
Excellent, nice clean work 👍🏽
I just purchased everything from your site, I would also love to purchase the mounting plate were you put the switch and supply chuck. Thanks for the awesome instructional video, professional job well done.
Give us a call at the shop Monday and we can add that to your order.
@@rockyour4x4 Awesome!, you made my install so much easier! Now I just need to invest in those wire stripers and crimpers you have.
@@rockyour4x4 I just left a voicemail for you guys.
Excellent tutorial, thanks!!!
inflate deflate tires ? while in the cabin ? that could be nice.
Great to see someone else doing this. Did something similar on my canyon when I got it in 2016
Great video! Learned a lot here!
Great video. Is it possible to have the compressor installed there and have the AEV snorkel?
Paul Watkins yes, that would work just fine.
@RockYour4x4 do you sell those same fittings or have a recommendation on where to purchase?
We sell it all.
Awesome installation 👍🇺🇸
Thank you the Vermonter
Thank you
@@rockyour4x4 You guys set a high bar for excellent install videos! I just stumbled upon your channel and hit the subscribe and like buttons.
Fantastic video! Very detailed and straight forward. Looking forward to getting my 2022 (which is still on order) and installing this. If I were to use an S-Pod, how would those wires connect? I'm thinking the main power wires would still go to the battery, but the black and purple wire would go to the S-pod? Any tips would be appreciated.
Again, great job. Thanks for posting this one!
You are correct.
@@rockyour4x4 Thank you for responding!
hey man looking to run a compressor set up on the zr2. Would you recommend going with the dual or do you think the single is adequate for the average offroader.
I think the single is adequate but the dual is so much faster.
Great video! Got my twin delivered today. Where did you put the thin small blue/white and red/yellow wires that power the switch?
They are fused and on a stud of the fuse block.
Hi, I really enjoy this series. I recently purchased a new 2019 ZR2 Bison for a do everything vehicle: daily driver, light off roading, and long trips. Since it's a Bison a lot of the mods you've completed were already done, and I've added a Comeup winch, GMPP front level kit and tie rod sleeves. I think air and new tires/wheels might be it (I also have GoFast camper top on order, but that a ways out). I have a few questions that I hope you can help me with:
1) Tire and wheels: At this point I would just be going to 285/75, not 35", and I am looking at going down to 16" wheel for more sidewall and air volume. The Method Race Wheel 702 is 16x8, 6x120, +30/5.60 ,which is almost exactly the offset of the stock wheels. Would this set up work? Would a 0 offset wheel be better? I'm a bit concerned about the bigger tire hitting the upper control arm, but I don't see anything online about that and it seems that lots of people are running 285/75 on stock wheels.
2) Is there any point in saving money and going with a ARB single compressor?
3) Random little questions. The AEV fairlead comes with those bolts that have a 6mm hex key drive. I find that these are really tough to tighten with any toque and not damage, they seem better suited for a bicycle than a truck! Do you have torque specs for the these bolts? I can't seem to find anything online.
Thanks for your help and if Im ever in the Knoxville area I'll be sure to stop by.
Is the blue AND red wire fused together on the stud of that fuse block? I'm just curious as to why the switch doesn't stay lit up if the blue wire is connected to the battery. Nice work!!
Yes, blue and red together. Nice catch!
@@rockyour4x4 Nice. Why then doesn't the switch light stay on? I noticed in the video it's off until you turn switch on. I was worried if I fuse those two wires together the light will stay on all the time. Thanks! By the way I ordered your Sherman Cap and love it...nice little addition to the project.
@@MrCoryReynolds the red wire is connected to constant but the blue wire is pulled back to switched power at the same terminal as the compressor.
How are the air lines holding up being ran across the radiator?
No issues at all.
Wonder if the ZR2 V6 has that much room under the overflow tank 🤔 I'd love to do this!
It does.
Installed the same compressor and used the same bracket on my 2021 V6 and had room. Good to go : )
id like to get your thoughts on tires its time for me to get a new set for my YJ , i like to drive it to the trails i figure you would know a good tire for duel use.
James Barnes check out the Nitto Ridge Grappler
Why put the compressor in hot engine compartment
Because that’s wasted area and it does not affect the performance of that compressor one bit.
Excess heat will shorten the life of anything, don’t see how a air compressor would be exempt from that 🤷♂️
@@ridered7394 we install hundreds of these. The heat from the compressor filling (4) 40” tires trumps any heat radiating from the engine in the back corner of the engine bay.
Is there any chance you guys can make me the bracket for the switch/ sherman cap for my ZR2?
We can.
@@rockyour4x4 Should I just call you guys later today? I placed an order with you guys for all the other stuff yesterday
Yessir
@@rockyour4x4 Sent you a message on your contact page on your site. Included my order number. need that bracket made. please get back to me with a price so i can get this project going.
@@mattfrediani7924 any progress on getting that bracket? I just emailed them today to see if I can pick one up also.