hello CBI solar, i have a battery bank containing 80 units of trojan SAGM 06v 315AH batteries connected in series-parallel. and i use 2 units of context xw+ inverter 48v, please what max charge rate should the inverters be set? Thank you
I have got a Scneider 4048 inverter, An Outback flex 80 and 8 12 v 200 AH Renogy gel batteries. I have checked the batteries and they are Ok. I have my OUTBACK flex at 60 . Something is strande my batterie volts drop )not used= from 54 v to 49 at a heart beat. Is there something I have to adjust at my inverter?
@@camosolarinc7697 thanks for clarifying that for me. Is there a guide on how to use the LAN to set up the warm up? I have the conext sw 4042 inverter. I cant find anything in the install or user guide and dont want to damage my diesel genset by having a load on start. Its -40 celisus here and even though i got the block heater pluged in it cant be good on the genset to not get a warm up.
I have it set when my generator runs it seems like my batteries are getting really hot and it says it is full charge in only 2 min after gen starts and then the gen shuts off more concerned if I have my generator set up right
I see. Have you set up your schneider already and are worried about the settings being correct? Or are you setting it up fresh right now? Who sold you the system?
Could you use the AC2 input to tie to the grid and then control when you are connected to the grid with the generator control module?
Hi, do you need to have the AGS module installed or does this unit act as an AGS? I have the same system and just installing a back up generator.
do you guys ever read the comments?
hello CBI solar, i have a battery bank containing 80 units of trojan SAGM 06v 315AH batteries connected in series-parallel. and i use 2 units of context xw+ inverter 48v, please what max charge rate should the inverters be set?
Thank you
Hello... Did you figure the max charge rate for your inverters? Looking into something similar myself. Thanks in advance...
I have got a Scneider 4048 inverter, An Outback flex 80 and 8 12 v 200 AH Renogy gel batteries. I have checked the batteries and they are Ok. I have my OUTBACK flex at 60 . Something is strande my batterie volts drop )not used= from 54 v to 49 at a heart beat. Is there something I have to adjust at my inverter?
Sounds like you have a bad battery , please chech each battery under load and see if one is bad
How do I get that combox information that reads that information?
I have a generator aims 3200w but it is 120 I can connect it to the schneider 4048 system
I would like to see how it was connected to the generator. What wires go where?
Each Genset is different and there way of starting
the investor has it 120 or 230?
What's a BAT TREE?
HI I HAVE 8 L16H-AC TROJAN BATTERRY 6V AND Schneider conext inverter CAN U RECOMMEND ME THE BEST CHARGING SETTINGS FOR THIS MODEL?
please got to your battery website and find what thay recomend
How do you set the warm up mode time? I cant seem to find it in any of the settings.
Ya sorry Schneider put the warm up time in the Inverter and the only way is to have your computer talk to it on the LAN on the gateway or Combox
@@camosolarinc7697 thanks for clarifying that for me. Is there a guide on how to use the LAN to set up the warm up? I have the conext sw 4042 inverter. I cant find anything in the install or user guide and dont want to damage my diesel genset by having a load on start. Its -40 celisus here and even though i got the block heater pluged in it cant be good on the genset to not get a warm up.
charge rate up to high 70 amps will do
I have it set when my generator runs it seems like my batteries are getting really hot and it says it is full charge in only 2 min after gen starts and then the gen shuts off more concerned if I have my generator set up right
if your batteries get hot you have a big problem how many Amp hour is your battery and how many amps are you pushing
I have a 1000 amp hour agm wet filled battery bank would you know my correct settings
Battery settings generally have to be obtained from the battery manufacturer. What is their make and model?
Start off with a 3-stage charge rate 60 amp bulk and float
i turn my ac on gos strait to charge how do i set dc prioroty
Im not understanding your Question or what you mean
What generator do you use?
I would like to know too
How to sync Schneider 6048 to 220v
Gnb wet filled
I see. Have you set up your schneider already and are worried about the settings being correct? Or are you setting it up fresh right now? Who sold you the system?